DeerValley DV-1SD0401S08

DeerValley Fixed Glass Shower Panel

Model: DV-1SD0401S08

1. Enfòmasyon sou Sekirite

This DeerValley fixed glass shower panel is constructed from 5/16 inch (8 mm) thick tempered safety glass. Tempered glass is designed to be highly durable and shatter-resistant. In the rare event of breakage, it will fragment into small, granular pieces, significantly reducing the risk of injury compared to ordinary glass.

Always handle glass panels with care. Two strong individuals are recommended for lifting and positioning the glass due to its weight and size. Wear appropriate safety gear, including gloves and eye protection, during installation.

Diagram illustrating tempered glass safety features and breakage pattern

Image: Tempered glass is 4-5 times stronger than ordinary glass and shatters into small, blunt pieces for safety.

Comparison of tempered glass breakage versus ordinary glass breakage

Image: Tempered glass breaks into small, less hazardous particles, unlike ordinary glass which forms sharp shards.

2. Pwodwi souview

The DeerValley Fixed Glass Shower Panel (Model DV-1SD0401S08) is a frameless shower screen designed for walk-in showers. It features a static, wall-mounted design, providing an open and airy showering experience. The panel measures 34 inches in width and 74 inches in height.

Karakteristik kle yo enkli:

  • Explosion-Proof Tempered Glass: 5/16" (8 mm) thick for enhanced safety.
  • Wall-Mounted Fixed Design: Ensures stability and a secure installation.
  • Premium Stainless Steel Hardware: Provides durability and corrosion resistance.
  • Water-Resistant Seal Strip: Included to minimize water leakage.
  • Enstalasyon Revèsib: Can be mounted for left or right-side configurations.
Diagram showing the dimensions of the DeerValley shower glass panel

Image: Model information and configuration dimensions for the 34 inch wide by 74 inch high shower panel.

3. Lis konpozan yo

Verifye ke tout konpozan yo prezan epi yo pa domaje anvan ou kòmanse enstalasyon an. Si gen nenpòt pyès ki manke oswa ki domaje, kontakte sèvis kliyan.

AtikDeskripsyonKantite
Panel Glass5/16" (8mm) Tempered Glass1
Mi clampsNerjaveèi asye Mounting Materyèl4 (tipikman)
Seal StripBottom water-resistant seal1
Materyèl enstalasyonScrews, wall anchors, Allen keyMete

4. Enstalasyon ak Enstalasyon

Installation requires careful measurement and handling. It is recommended to have at least two people for the installation process.

4.1 Etap Pre-Enstalasyon

  1. Enspekte pwodwi a: Unpack all components and inspect for any damage. Do not proceed with installation if the glass is chipped, cracked, or scratched.
  2. Prepare zòn nan: Ensure the shower area walls and floor are level and clean. Mark the desired position of the glass panel on the wall.
  3. Rasanble zouti: You will need a drill, level, measuring tape, pencil, screwdriver, and possibly a caulk gun with silicone sealant (not included).

4.2 Mounting the Wall Clamps

The panel uses multi-point wall mounting for a secure fit. The stainless steel clamps are designed to hold the glass firmly.

  1. Mark the positions for the wall clamps on your shower wall, ensuring they are level and correctly spaced according to the panel dimensions.
  2. Drill pilot holes at the marked locations. If drilling into tile, use a tile drill bit. Insert wall anchors if necessary.
  3. Secure the wall clamps to the wall using the provided screws. Ensure they are tightly fastened.
Close-up of a glass clamp securing the shower panel to the wall

Image: Quality glass clamps provide solid support for the shower panel.

4.3 Positioning the Glass Panel

The panel is designed for reversible installation, allowing for left or right wall mounting.

  1. With assistance, carefully lift the glass panel and position it into the installed wall clamps.
  2. Ensure the panel is plumb and level. Adjust as needed before tightening the clamp mete vis.
  3. Tighten the set screws on the clamps to firmly secure the glass panel. Do not overtighten.
Diagram showing left and right wall installation options for the shower panel

Image: The shower panel supports reversible installation for left or right wall mounting.

4.4 Installing the Seal Strip

The bottom seal strip helps prevent water leakage.

  1. Clean the bottom edge of the glass panel where the seal strip will be applied.
  2. Carefully slide or press the seal strip onto the bottom edge of the glass panel. Ensure it forms a snug fit.
  3. Apply a bead of silicone sealant along the exterior base of the panel where it meets the shower floor, and along the wall edge if desired, to enhance waterproofing. Allow adequate drying time before use.
Diagram illustrating the waterproof design with side seal strip and lower water bar

Image: The waterproof design includes a side seal strip and lower water bar for dry and wet separation.

Illustration of wet and dry areas in a shower with the panel installed

Image: The shower panel helps create distinct wet and dry zones, minimizing water spillage.

5. Operasyon

This is a fixed glass shower panel and does not have moving parts. Its function is to define the shower area and contain water spray. Ensure the seal strip is properly seated to prevent water from escaping the shower area.

6. Antretyen

Regular cleaning and maintenance will preserve the appearance and functionality of your shower panel.

6.1 Netwayaj Vit

  • Use a soft cloth or sponge with a non-abrasive glass cleaner or a solution of mild soap and water.
  • Avoid abrasive cleaners, scouring pads, or harsh chemicals, as these can scratch the glass or damage protective coatings.
  • For best results, wipe down the glass after each use to prevent water spots and soap scum buildup. A squeegee can be effective.

6.2 Hardware Cleaning

  • Clean stainless steel hardware with a soft, damp twal.
  • Avoid using abrasive cleaners or strong chemicals on the hardware, as they can damage the finish.
  • Tcheke tout vis ak koneksyon yo detanzantan pou asire yo rete sere.

NAN. Depanaj

7.1 Flit Dlo

  • Pwoblèm: Water leaks from the bottom or sides of the panel.
  • Solisyon:
    • Ensure the bottom seal strip is correctly installed and forms a tight seal with the shower floor.
    • Check for gaps along the wall where the panel is mounted. Apply a continuous bead of silicone sealant along the exterior seams if necessary.
    • Verify that the shower floor is level. Uneven surfaces can cause water to pool and leak.

7.2 Panel Instability

  • Pwoblèm: The glass panel feels loose or wobbly.
  • Solisyon:
    • Tighten all set screws on the wall clamps. Do not overtighten, as this can damage the glass.
    • Ensure the wall clamps are securely fastened to the wall. If they are loose, re-secure them with appropriate wall anchors.

8. Espesifikasyon

KarakteristikDetay
MakDeerValley
Nimewo ModèlDV-1SD0401S08
Dimansyon (W x H)34 pous x 74 pous
Epesè vè5/16 pous (8 mm)
Kalite vèTanpered Sekirite Glass
Materyèl MateryèlNerjaveèi asye
KoulèSilver (Hardware)
Asanble obligatwaWi
UPC710329824880

9. Garanti ak sipò

For specific warranty details and customer support, please refer to the documentation included with your purchase or contact DeerValley directly through their official websit entènèt la oswa chanèl sèvis kliyan yo. Kenbe prèv acha ou pou reklamasyon garanti.

© 2024 DeerValley. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.