gofanco Logo

4 HDMI 1.4 Splitter/Extender
Korisnički priručnikgofanco HDExt4P-HD14 1x4 HDMI 1.4 Splitter Extender

Hvala vam što ste kupili od gofanco. Naši proizvodi imaju za cilj zadovoljiti sve vaše potrebe za povezivanjem kamo god krenuli. Za optimalne performanse i sigurnost, pažljivo pročitajte upute i sačuvajte ovaj Korisnički priručnik za buduću uporabu. Ako trebate više informacija o našim proizvodima, posjetite www.gofanco.com. Za tehničku podršku pošaljite nam e -poruku na [e-pošta zaštićena]. Za upravljačke programe ili ručno preuzimanje, idite na www.gofanco.com/downloads.

Važne sigurnosne napomene
Prije instalacije i rada pažljivo pročitajte sigurnosne upute.

  • Obratite posebnu pozornost na sva upozorenja i savjete za ovaj uređaj
  • Ne izlažite ovaj uređaj kiši, velikoj vlazi ili tekućini
  • Ne stavljajte nikakve predmete u uređaj niti pokušavajte promijeniti njegov rad
  • Do not repair the device or open the enclosure without professional guidance to avoid electric shocks. Doing so may void your warranty Keep the product in a well- entilated location to avoid damage from overheating
  • Prije instalacije isključite napajanje i provjerite je li okolina sigurna
  • Nemojte uključivati/isključivati ​​HDMI i IC kabele dok je uređaj u upotrebi kako biste izbjegli oštećenja kabela. Provjerite jesu li priključeni na ispravne priključke
  • Koristite samo isporučeni adapter za napajanje. Provjerite odgovaraju li specifikacije ako koristite istosmjerne ispravljače za struju treće strane

Uvod
The 1×4 HDMI 1.4 Splitter/Extender distributes HDMI signals from one source device to four CAT6/7 outputs and one HDMI output (loop out).
Značajke

  • Distributes HDMI signals from one source to four CAT6/7 outputs
  • One HDMI loop-out on the transmitter CAT6/7 outputs: Up to 70m (230ft) at 1080p and 50m (164ft) at 4K
  • Usklađeni sa HDMI 1.4 i HDCP 1.4
  • Podržava do [e-pošta zaštićena] YUV 4:4:4, 1080p @60Hz YUV 4:4:4
  • Supports Power over Cable (PoC), bi-directional IR control, audio extraction, and firmware upgradeable
  • Kašnjenje blizu nule
  • Lightning/Surge/ESD protection Installation Requirements
  • HDMI izvorni uređaji (DVD uređaj, set-top box, računalo itd.)
  • HDMI zasloni (SDTV/Monitor, HDTV/Monitor, projektor itd.)
  • HDMI kabeli (nisu uključeni)
  • CAT cables (not included)

Sadržaj pakiranja

1×4 HDMI 1.4 Splitter/Extender

  • 1x 1×4 HDMI 1.4 Splitter/Extender
  • 4x CAT6/7 Receivers
  • 5x IR Receiver cables
  • 1x IR Emitter cable
  • 1x Power adapter (24V/2.71A)
  • Pribor za površinsku montažu
  • 4x Velcro strips
  • 4x Plastic cushions
  • 1x Korisnički vodič

Izgled proizvodagofanco HDExt4P-HD14 1x4 HDMI 1.4 Splitter Extender -

  1.  Power LED: On when the Splitter/Extender is powered on; Off when the Splitter/Extender is powered off
  2. EDID: 3-Pin EDID selector switch
    • 5.1CH Audio: Uses EDID [e-pošta zaštićena] 5.1CH
    • 2.0CH Audio: Uses EDID [e-pošta zaštićena] 2.1CH
    • Copy Display: Uses the EDID of the connected display with the lowest resolution

gofanco HDExt4P-HD14 1x4 HDMI 1.4 Splitter Extender - fig 1

  1. HDMI ulaz: Povezuje se na vaš HDMI izvor
  2. Izlazi:
    HDMI Loopout: Povezuje se na lokalni HDMI zaslon
    CAT6/7 Out (1-4): Connects to the CAT6/7 In of the CAT6/7 Receivers using a CAT6/7 cable. It supports PoC to power the receiver over a CAT cable. The orange LED illuminates when an HDMI signal is detected. The green LED illuminates when powered on
  3. IC ulaz: Five 3.5mm IR input jacks for connecting the IR Receivers
    IR All In: Connects to an IR Receiver cable. Sends IR signals to all CAT6/7 Receivers to control all display devices
    • IR In (1-4): Connects to an IR Receiver cable. Sends IR signals to the respective CAT6/7 Receiver to control the display device
  4. Kontrolirati:
    • IR Out: Connects to an IR Emitter cable. Receives IR signals from the CAT6/7 Receivers to control the source device
    • FW: USB Type-A port for firmware update
  5. Audio izlaz:
    • S/PDIF Out: Toslink output for audio de-embedding from the HDMI output
    • L/R Out: RCA analog stereo output for audio de-embedding from the HDMI output
  6. Utičnica za napajanje: Connects to the included 24V power adapter

gofanco HDExt4P-HD14 1x4 HDMI 1.4 Splitter Extender - Power Jack

  1. HDMI izlaz: Povezuje se na HDMI zaslon
  2. CAT6/7 In: Connects to the CAT6/7 Out of the Splitter/Extender using a CAT6/7 cable. It supports PoC to power the receiver over a CAT cable. The orange LED illuminates when an HDMI signal is detected. The green LED illuminates when powered on
  3. IC ulaz: Connects to an IR Receiver cable
  4. IC izlaz: Connects to an IR Emitter cable

Instalacija hardvera

  1. Isključite sve uređaje, uključujući HDMI izvor i HDMI zaslon (e).
  2. Connect your HDMI source device to the 1×4 HDMI 1.4 Splitter/Extender’s HDMI In connector with an HDMI cable (HDMI cable not included).
  3. Connect your CAT6/7 cables between the Splitter/ Extender and CAT6/7 Receivers.
  4. Optional: Connect an HDMI display to the HDMI Out connector of the Splitter/Extender using an HDMI cable (HDMI cable not included). This connection is needed only if you require local monitoring of the HDMI signal.
  5. Connect an HDMI display to each CAT6/7 Receiver’s HDMI Out connector with an HDMI cable (HDMI cables not included).
  6. Optional: Connect the IR Receiver cables and the IR Emitter cable to the IR interface ports. This connection is needed only if you need to control your HDMI devices from a remote location. See IR Control, starting on page 9, for proper IR connection.
  7. Plug the included power adapter into the Splitter/ Extender’s Power Jack, then plug the power adapter into a reliable power outlet. Note: The CAT6/7 Receivers do not need power adapters, they can be powered from the Splitter/Extender over CAT cable with PoC technology.
  8. Power on your HDMI source device and HDMI display(s). The Splitter/Extender is ready for use.

Dijagram primjene

The application diagram shows the most typical input and output devices used with the Splitter/Extender.gofanco HDExt4P-HD14 1x4 HDMI 1.4 Splitter Extender - Diagram

CAT ožičenje kabela
We suggest both RJ-45 connectors be wired identically using the T568B wiring standard for the best performance and compatibility. Both connectors must be wired identically, to the T568B standard.

gofanco HDExt4P-HD14 1x4 HDMI 1.4 Splitter Extender - fig 2 gofanco HDExt4P-HD14 1x4 HDMI 1.4 Splitter Extender - fig 3

Bilješka: You may use cat5e. cat6 UTP (cat6 preferred) in conjunction with the RJ45 output: however for best performance use cat6a or cat7 (particularly in electrically noisy environments). The maximum distances & transmission performance for HDMI and USB may be compromised by cable quality and patch panels. poor termination, wall plates. cable kinks and electrical interferences. Generally, ensure the cat cable is a solid copper core of 23AWG (avoid CCA type). in one straight run (avoid/minimize patches) and avoid close proximity to any noisy electrical sources.
IR kontrola
Provides IR control of the connected devices. The IR feature is bi-directional so either the source device or the display device(s) can be remotely controlled. Controlling the Source Device

  1. Connect an IR Emitter Cable to the IR Out port of the Splitter/Extender.
  2. Point the IR Emitter Cable’s IR eye in line with the source device’s IR window.
  3. Connect an IR Receiver Cable to the IR In port on each CAT6/7 Receiver

gofanco HDExt4P-HD14 1x4 HDMI 1.4 Splitter Extender - Diagra Figure 5: Source Device IR Control Connection Diagram

Controlling the Display Device(s) using IR In
Allows you to remotely control each display individually.

  1.  Connect an IR Receiver Cable to the IR In the port of the Splitter/Extender.
  2. Connect an IR Emitter Cable to the IR Out port on each CAT6/7 Receiver.
  3. Point the IR Emitter Cable’s IR eye in line with the display’s IR window.gofanco HDExt4P-HD14 1x4 HDMI 1.4 Splitter Extender - IR Emitter

Controlling the Display Device(s) using IR All-In Port
Allows remote controlling of all of the display devices simultaneously.
1. Connect an IR Receiver Cable to the IR All-In port of the Splitter/Extender.
2. Connect an IR Emitter Cable to the IR Out port on each CAT6/7 Receiver.
3. Point the IR Emitter Cable’s IR eye in line with the display’s IR window.gofanco HDExt4P-HD14 1x4 HDMI 1.4 Splitter Extender - fig 4

Bilješka:
The IR All In will relay the received IR signal to all the CAT6/7 outputs whereas the IR IN connectors associated with each CAT6/7 output will only relay the IR signal to its respective CAT6/7 Receiver. The Splitter/Extender’s IR Out connector will output the IR signals received from any of the CAT6/7 Receivers, so as to allow control of a source from any of the remote CAT6/7 Receivers.

Česta pitanja i rješavanje problema

Q: Poor video quality or no video signal on display:
A1: Check whether the HDMI cables are connected properly and are in good working condition.
A2: Make sure the resolution of the display is compatible with the splitter’s resolution
Q: No HDMI signal output from the CAT6/7 connectors while the local HDMI out port is working normally:
A1: Check whether the HDMI cables are connected properly and are in good working condition.
Q: Splash screen on the displays:
A1: Cause of damaged or low-quality HDMI cables. Change to a higher-quality HDMI cable.

Tehnički podaci

1×4 HDMI 1.4 Splitter/Extender

Video Input
Ulazni (1) HDMI
Ulazni priključak (1) Female type A HDMI
HDMI ulazna razlučivost Up to 4K©30Hz 4:4:4
Video izlaz
Izlaz (1) HDMI; (4) CATx
Izlazni priključak (1) Female type A HDMI; (4) RJ45
HDMI izlazna rezolucija Up to 4K©30Hz 4:4:4 8bit.
CATx Output Resolution Up to 4K©30Hz 4:4:4 8bit.
SPDIF Audio Output
Audio izlaz (1) SPDIF
Audio izlazni priključak (1) Toslink
Audio Format LPCM 2ch, Dolby Digital 5.1ch, and DTS 5.1ch
Izlazna razina ±0.05 dBFS
Frekvencijski odziv 20Hz -20kHz, it dB
THD + N < 0.05%, 20Hz -20kHz bandwidth, 1kHz sine at OdBFS level (or max level)
SNR > 90dB, 20Hz -20kHz bandwidth
Izolacija preslušavanja > 70dB, 10kHz sine at OdBFS level (or max level before clipping)
Buka -90dB
Analogni audio izlaz
Audio izlaz (1) Analog audio
Audio izlazni priključak (1) RCA
Audio Format PCM 2CH
Frekvencijski odziv 20Hz -20kHz, ±1dB
Maksimalna razina izlaza 2.0Vrms ± 0.5dB.
THD + N < 0.05%, 20Hz -20kHz bandwidth, 1kHz sine at OdBFS level (or max level)
SNR > 80dB, 20Hz -20kHz bandwidth
Izolacija preslušavanja > 70 dB, 10kHz sine at OdBFS level (or max level before clipping)
LR devijacija razine < 0.3 dB, 1kHz sine at OdBFS level (or max level before clipping)
Mogućnost izlaznog opterećenja 1Kohm and higher (supports 10x paralleled 10kohm loads)
Buka - 80 dB

1×4 HDMI 1.4 Splitter/Extender Cont’d

kontrola
Kontrolni priključak (1) EDIT; (4) IR IN; (1) IR ALL IN; (1) IR OUT; (1); FW
Upravljački priključak (1) 3-pin DIP switch; (6) 3.5mm mini jacks; (1) USB-A port
Osnovne informacije
HDMI standard HDMI 1.4 with HDCP 1.4
Prijenos način CAT5e/6/7 Cable
Prijenos Udaljenost 1080p s 230 feet (70 meters), 4K 5164 feet (50 meters)
Radna temperatura -5 to +55t (+23° to +131°F)
Temperatura skladištenja -25 to +70*C (-13° to +158°F)
Relativna vlažnost 10% do 90%, bez kondenzacije
Ulazna snaga AC adaptera 100V-240V AC, 50/60Hz
Ulazna snaga 24 V DC 2.71A
Potrošnja energije 15W (maks.)
Dimenzija (Š * V * D) 168mm x 44mm x 100mm
Neto Težina 585g

CAT6/7 Receiver

Video
Ulazni (1) CATx
Ulazni priključak (1) RJ45
Razlučivost ulaza Up to 4K©30Hz 4:4:4 8bit
Izlaz (1) HDMI
Izlazni priključak (1) Tip-A ženski HDMI
Izlazna razlučivost Up to 4K©30Hz 4:4:4 8bit
kontrola
Kontrolni dio (1)IR In, (1) IR Out
Upravljački priključak (2)3.5mm mini jacks
Osnovne informacije
HDMI standard HDMI 1.4 with HDCP 1.4
Prijenos Udaljenost 1080p 5230 feet (70 meters), 4K 5164 feet (50 meters)
Radna temperatura -5— +55°C
Temperatura skladištenja -25 — +70°C
Relativna vlažnost 10%-90%

Izjava o odricanju od odgovornosti
The product name and brand name may be registered trademarks of related manufacturers. TM and ® may be omitted from the user’s guide. The pictures on the user’s guide are just for reference, and there may be some slight differences with the actual products. We reserve the right to make changes without prior notice to a product or system described herein to improve reliability, function, or design.

gofanco Logo Hvala vam što ste odabrali gofanco
www.gofanco.com

Dokumenti / Resursi

gofanco HDExt4P-HD14 1x4 HDMI 1.4 Splitter Extender [pdf] Korisnički priručnik
HDExt4P-HD14, 1x4 HDMI 1.4 Splitter Extender, Splitter Extender, HDExt4P-HD14, Extender

Ostavite komentar

Vaša adresa e-pošte neće biti objavljena.