FOS technology Razor Laser Multibeam RGB Laser Moving Head Korisnički priručnik

FOS technologies Razor Laser Multibeam RGB Laser Moving Head

Raspakiravanje

Thank you for choosing our products. For your own safety, please read this manual before installing the device. This manual covers important information on installation and applications. Please install and operate the fixture with the following instructions, make sure the power is off before opening the light or repairing it. Meanwhile, please keep this manual well for future needs.

It is made of a new type of high-temperature strength of engineering plastics and cast aluminum casing with nice outlook. The fixture is designed and manufactured strictly following CE standards, complying with international standard DMX512 protocol. It’s available independently controlled and linkable with each other for operation. And it is applicable for large-scale live performances, theaters, studios, nightclubs and discos. 6 modules RGB laser light which features high brightness and stability. Please carefully unpack it when you receive the fixture and check whether it is damaged during the transportation.

Sigurnosne upute

OPREZ!
Budite oprezni sa svojim operacijama. S opasnim svtage, you can suffer a dangerous electric shock when touching wires

This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this user manual.

Važno:
Oštećenja uzrokovana nepoštivanjem ovog korisničkog priručnika ne podliježu jamstvu. Trgovac neće prihvatiti odgovornost za bilo kakve nastale nedostatke ili probleme.

If the device has been exposed to temperature changes due to environmental changes, do not switch it on immediately. The arising condensation could damage the device. Leave the device switched off until it has reached room temperature. This device falls under protection-class I. Therefore, it is essential that the device be earthed. The electric connection must carry out by a qualified person. The device shall only be used with rate voltage i frekvencija. Provjerite je li dostupan voltage is not higher than stated at the end of this manual. Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case, replacement of the cable must be done by an authorized dealer.

Uvijek isključite iz električne mreže, kada se uređaj ne koristi ili prije čišćenja. Kabelom za napajanje rukujte samo za utikač. Nikada nemojte izvlačiti utikač povlačenjem kabela za napajanje.

During the initial start-up, some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective, it should decrease gradually. Please don’t project the beam onto combustible substances. Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for smooth air flow, so there should be no shelter for fans and ventilation for heat radiation. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

Glavne značajke

• Voltage: AC100-240V,50/60HZ
• Laser color: RGB full color
• Laserska snaga: 3W
• RGB 500mw*6PCS （R:100mw G:200mw B:200mw） Laser pattern: a variety of rough beam effect patterns.
• Y-Axis rotating: 240°
• Kut okretanja: 270 °
• Control mode: Music / Automatic / DMX512 (11/26/38CH) Scanning system: stepping motor
• Scanning angle of motor: 25 degrees
• Rated power：<180W
• Working environment: indoor Lamp
• Veličina proizvoda: 85 x 16 x 45 cm
• Size of carton case (1in1): 92 x 16 x 32 cm
• N.W: 11kgs / G.W：12.6kgs
• Size of carton case (2in1): 94.5 x 34 x 33.5 cm
• N.W: 23kgs / G.W：26.5kgs

Upute za uporabu

• The moving head is for laser purposes.
• Don’t turn on the fixture if it’s been through severe temperature difference like after transportation because it might damage the light due to the environmental changes. So, make sure to operate the fixture until it is in normal temperature.
• Ovo svjetlo treba držati podalje od jake trešnje tijekom bilo kakvog transporta ili kretanja.
• Ne povlačite svjetlo samo za glavu jer bi moglo oštetiti mehaničke dijelove.
• Don’t expose the fixture in overheat, moisture or environment with too much dust when installing it. And don’t lay any power cables on the floor. Or it might cause electronic shock to the people.
• Provjerite je li mjesto ugradnje u dobrom sigurnosnom stanju prije ugradnje učvršćenja.
• Obavezno stavite sigurnosni lanac i provjerite jesu li vijci dobro zavrnuti prilikom postavljanja učvršćenja.
• Make sure the lens is in good condition. It’s recommended to replace the units if there are any damages or severe scratches.
• Prije uporabe uvjerite se da uređajem upravlja kvalificirano osoblje koje poznaje uređaj.
• Zadržite originalne pakete ako je potrebna druga pošiljka.
• Ne pokušavajte mijenjati svjetiljke bez ikakvih uputa od strane proizvođača ili ovlaštenih servisera.
• Nije u rasponu jamstva ako postoje bilo kakvi kvarovi zbog nepridržavanja korisničkog priručnika za rad ili bilo koje nezakonite radnje, poput kratkog spoja, elektroničkog udara, lamp slomljen, itd.

Display menu control

Press MENU to choose Address / DMX/ Color/ Manual/ Demo /Auto/Sound/ Temp /Version /Hours, then press ENTER to confirm or to enter the next step.if there are more function for options, press UP/DOWN to choose, then press ENTER to confirm, then press MENU to exit, or wait for 10 and exit automatically.

Napomene:
If no operation on any button, the display will turn off automatically in 20 seconds; if no DMX signal, the first dot of the display will turn on statically, if with DMX signal, the dot will flash

• DMX Address A001
• A512 Address Code
• Channel Mode 11CH, 26CH, 38
• CH channel selection
• Show Mode SOUND AUTO, effect selection
• Slave Mode MASTER, SLAVE, main and auxiliary machine selection
• Black Out YES, NO Standby mode
• Sound State ON, OFF voice switch
• Sound Sense sound sensitivity (0 off, 100 most sensitive)
• Pan inverzno
• YES, NO level reverse
• Tilt1 Inverse YES, NO vertical reverse
• Tilt2 Inverse YES, NO vertical reverse
• Tilt3 Inverse YES, NO vertical reverse
• Tilt4 Inverse YES, NO vertical reverse
• Tilt5 Inverse YES, NO vertical reverse
• Tilt6 Inverse YES, NO vertical reverse
• Back Light ON, OFF backlight switch
• Auto Test Auto Test
• Firmware Version V104 software version number
• Defaults YES, NO Restore factory settings
• System Reset YES, NO Machine reset

DMX Channels 11Channel Mode

CH	funkcija	DMX vrijednost	Detaljnije
1	Pan motor	0-255	0-360°positioning
2	Pan motor brzina	0-255	Od brzog do sporog
3	Tilt1—Tilt6 motor stroke	0-255	0 no function 1-255 0°-360° positioning
4	Motor nagiba brzina	0-255	Od brzog do sporog
5	Samohodni	0-55	Nema funkcije
		56-80	Self-propelled effect 1 (XY uncontrollable)
		81-105 106-130 131-155 156-180	Self-propelled effect 2 (XY uncontrollable)…Self-propelled effect 5 (XY uncontrollable)
		181-205	Sound control (XY uncontrollable)
		206-230	Self-propelled effect 6 (XY uncontrollable)
		231-255	Sound control (XY uncontrollable)
6	Samohodni brzina	0-255	self-propelled speed and Sound-activated sensitivity
7	prekidač za kratka svjetla	0-255	0-100% total dimming
8	Strobe	0-9	Nema stroboskopa
		10-255	Brzina stroboskopa od sporog do brzog
9	Učinak lasera	0-15	Nema funkcije
		16-27	Učinak 1
		......	Every time the DMX value is increased by 12, there will be an effect
		232-243	Učinak 19
		244-255	Učinak 20
10	Učinak lasera	0-255	self-propelled speed from fast

	brzina		presporo
11	Reset	0-249	Nema funkcije
		250-255	machine reset (value stays for 5 sekunde)

26Channel Mode

CH	funkcija	DMX vrijednost	Detaljnije
1	Pan motor	0-255	0-360°positioning
2	Pan motor brzina	0-255	Od brzog do sporog
3	Tilt1 motor	0-255	0°-360° positioning
4	Tilt2 motor	0-255	0°-360° positioning
5	Tilt3 motor	0-255	0°-360° positioning
6	Tilt4 motor	0-255	0°-360° positioning
7	Tilt5 motor	0-255	0°-360° positioning
8	Tilt6 motor	0-255	0°-360° positioning
9	Tilt1-Tilt6 motor	0-255	0 no function     1-255 0°-360° pozicioniranje
10	Motor nagiba brzina	0-255	speed from fast to slow
11	Samohodni	0-55	Nema funkcije
		56-80	Self-propelled effect 1 (XY uncontrollable)
		81-105 106-130 131-155 156-180	Self-propelled effect 2 (XY uncontrollable)…Self-propelled effect 5 (XY uncontrollable)
		181-205	Sound control (XY uncontrollable)
		206-230	Self-propelled effect 6 (XY uncontrollable)
		231-255	Sound control (XY uncontrollable)
12	Samohodni brzina	0-255	self-propelled speed and Sound-activated sensitivity
13	prekidač za kratka svjetla	0-255	0-100% total dimming
14	Strobe	0-9	Nema stroboskopa
		10-255	Brzina stroboskopa od sporog do brzog
15	Red laser 1-6 prigušivanje	0-255	0 nema funkcije 1-255 1-100% dimming
16	Zeleni laser 1-6 dimming	0-255	0 nema funkcije 1-255 1-100% dimming

17	Blue laser 1-6 prigušivanje	0-255	0 no function       1-255 1-100% prigušivanje
18	The first group of RGB lasers	0-31	od
		32-63	crvena
		64-95	zelena
		96-127	plava
		128-159	Žut
		160-191	Ljubičasta
		192-223	Cijan
		224-255	Potpuno svijetlo
19	The second group of RGB lasers	0-31	od
		31-63	crvena
		64-95	zelena
		96-127	plava
		128-159	Žut
		160-191	Ljubičasta
		192-223	Cijan
		224-255	Potpuno svijetlo
20	The third group of RGB lasers	0-31	od
		32-63	crvena
		64-95	zelena
		96-127	plava
		128-159	Žut
		160-191	Ljubičasta
		192-223	Cijan
		224-255	Potpuno svijetlo
21	The fourth group of RGB lasers	0-31	od
		32-63	crvena
		64-95	zelena
		96-127	plava
		128-159	Žut
		160-191	Ljubičasta
		192-223	Cijan
		224-255	Potpuno svijetlo
22	The fifth group of RGB lasers	0-31	od
		32-63	crvena
		64-95	zelena
		96-127	plava
		128-159	Žut
		160-191	Ljubičasta
		192-223	Cijan
		224-255	Potpuno svijetlo
23	Šesti	0-31	od

	group of RGB lasers	32-63	crvena
		64-95	zelena
		96-127	plava
		128-159	Žut
		160-191	Ljubičasta
		192-223	Cijan
		224-255	Potpuno svijetlo
24	Učinak lasera	0-15	Nema funkcije
		16-27	Učinak 1
		......	Every time the DMX value is increased by 12, there will be an effect
		232-243	Učinak 19
		244-255	Učinak 20
25	Učinak lasera brzina	0-255	self-propelled speed from fast to sporo
26	Reset	0-249	Nema funkcije
		250-255	machine reset (value stays for 5 seconds)

38Channel Mode

CH	funkcija	DMX vrijednost	Detaljnije
1	Pan motor	0-255	0-360°positioning
2	Pan motor brzina	0-255	Od brzog do sporog
3	Tilt1 motor	0-255	0-360°positioning
4	Tilt2 motor	0-255	0-360°positioning
5	Tilt3 motor	0-255	0-360°positioning
6	Tilt4 motor	0-255	0-360°positioning
7	Tilt5 motor	0-255	0-360°positioning
8	Tilt6 motor	0-255	0-360°positioning
9	Tilt1—Tilt6 motor stroke	0-255	0 nema funkcije 1-255 0°-360° positioning
10	Tilt motor speed	0-255	speed from fast to slow
11	Samohodni	0-55	Nema funkcije
		56-80	Self-propelled effect 1 (XY uncontrollable)
		81-105 106-130 131-155 156-180	Self-propelled effect 2 (XY uncontrollable)…Self-propelled effect 5 (XY uncontrollable)
		181-205	Sound control (XY uncontrollable)
		206-230	Self-propelled effect 6 (XY

			uncontrollable)
		231-255	Sound control (XY uncontrollable)
12	Samohodni brzina	0-255	self-propelled speed and Sound-activated sensitivity
13	prekidač za kratka svjetla	0-255	0-100% total dimming
14	Strobe	0-9	Nema stroboskopa
		10-255	Brzina stroboskopa od sporog do brzog
15	Red laser 1-6 prigušivanje	0-255	0 nema funkcije 1-255    1-100% dimming
16	Green laser 1-6 prigušivanje	0-255	0 nema funkcije 1-255 1-100% dimming
17	Blue laser 1-6 prigušivanje	0-255	0 nema funkcije 1-255 1-100% dimming
18	The first group of red lasers	0-255	0-100% zatamnjivanje
19	The first group of green lasers	0-255	0-100% zatamnjivanje
20	The first group of blue lasers	0-255	0-100% zatamnjivanje
21	Drugi group of red lasers	0-255	0-100% zatamnjivanje
......	......	......	......
33	The sixth group of red lasers	0-255	0-100% zatamnjivanje
34	The sixth group of green lasers	0-255	0-100% zatamnjivanje
35	The sixth group of blue lasers	0-255	0-100% zatamnjivanje
36	Učinak lasera	0-15	Nema funkcije
		16-27	Učinak 1
		......	Every time the DMX value is increased by 12, there will be an effect
		232-243	Učinak 19
		244-255	Učinak 20
37	Učinak lasera brzina	0-255	self-propelled speed from fast to slow
38	Reset	0-249	Nema funkcije
		250-255	machine reset (value stays for 5 seconds)

Održavanje i čišćenje

Tijekom pregleda potrebno je uzeti u obzir sljedeće točke:

1. All screws for installing the devices or parts of the device must be tightly connected and must not be corroded.
2. There must not be any deformations on the housing, color lenses, fixations and installation spots (ceiling, suspension, trussing).
3. Mehanički pokretni dijelovi ne smiju pokazivati ​​nikakve tragove istrošenosti i ne smiju se okretati s neuravnoteženošću.
4. Električni kabeli za napajanje ne smiju imati oštećenja, zamor materijala ili naslage.

Further instructions depending on the installation spot and usage must be adhered by a skilled installer and any safety problems have to be removed.

OPREZ!
Prije početka rada s održavanjem isključite ga iz mreže.

In order to make the lights in good condition and extend the lifetime, we suggest a regular cleaning to the lights.

1. Clean the inside and outside lens each week to avoid the weakness of the lights due to the accumulation of dust.
2. Očistite ventilator svaki tjedan.
3. A detailed electric check by an approved electrical engineer every three months makes sure that the circuit contacts are in good condition, and prevents the poor contact of the circuit from overheating.

We recommend frequent cleaning of the device. Please use a moist, lint-free cloth. Never use alcohol or solvents. There are no serviceable parts inside the device. Please refer to the instructions under “Installation instructions”.

Dokumenti / Resursi

FOS technologies Razor Laser Multibeam RGB Laser Moving Head [pdf] Korisnički priručnik Razor Laser, Multibeam RGB Laser Moving Head, RGB Laser Moving Head, Moving Head, Razor Laser