Jauarta QS-WK16026 Digital Temperature Controller

1. Uvod

This manual provides comprehensive instructions for the safe and efficient operation of your Jauarta QS-WK16026 Digital Temperature Controller. This intelligent thermostat is designed for precise temperature regulation across a wide voltage range (AC 110-240V), suitable for various applications requiring stable temperature control.

Slika 1: Prednja strana view of the Jauarta QS-WK16026 Digital Temperature Controller.

2. Sigurnosne informacije

Please read and understand all safety instructions before using this device. Failure to follow these instructions may result in electric shock, fire, or serious injury.

• Provjerite je li napajanje voltage matches the device's specified range (AC 110-240V).
• Ne rukujte uređajem mokrim rukama ili u damp okruženja.
• Ne rastavljajte niti modificirajte uređaj. Za sve servisne radove obratite se kvalificiranom osoblju.
• Keep the device away from water, direct sunlight, and extreme temperatures.
• Osigurajte odgovarajuću ventilaciju oko uređaja.
• The ABS housing provides strong insulation; however, always handle with care to prevent damage.

3. Proizvod je gotovview

The Jauarta QS-WK16026 features an intuitive display and control buttons for easy temperature management.

Slika 2: Krupni plan view of the display and control panel.

Komponente:

• LED Digital Tube Display: Shows actual temperature (red), set start temperature (left yellow), and set stop temperature (right yellow).
• Start Setting Buttons: Up/Down arrows to adjust the desired start temperature.
• Stop Setting Buttons: Up/Down arrows to adjust the desired stop temperature.
• Statusno svjetlo: Indicates device operation (red light on = working, red light off = stopped).
• Utičnica: For connecting the heating or cooling device.
• Temperaturna sonda: Za precizno mjerenje temperature.

4. Specifikacije

5. Postavljanje

Follow these steps to set up your temperature controller:

1. Connect the Temperature Probe: Insert the temperature probe into the designated port on the controller. Ensure it is securely connected.
2. Postavite sondu: Place the temperature probe in the area where you wish to measure and control the temperature (e.g., fish tank, greenhouse).
3. Uključite uređaj: Connect the temperature controller's power plug into a suitable AC 110-240V power outlet.
4. Connect Heating/Cooling Appliance: Plug your heating or cooling appliance (e.g., heater, fan) into the power outlet on the temperature controller.

Figure 3: Temperature controller with power cord and probe connected.

6. Upute za rad

Razumijevanje zaslona:

• The red digital tube in the middle displays the current actual temperature measured by the probe.
• The left yellow digital tube displays the set start temperatura.
• The right yellow digital tube displays the set Stop temperatura.
• The red status light indicates when the connected appliance is active (on) or inactive (off).

Podešavanje temperature:

The controller operates in either heating or cooling mode based on the relationship between the set start and stop temperatures.

1. Postavite početnu temperaturu: Use the "Start Setting" up/down arrow buttons to adjust the desired temperature at which the connected appliance should activate.
2. Postavljanje temperature zaustavljanja: Use the "Stop Setting" up/down arrow buttons to adjust the desired temperature at which the connected appliance should deactivate.

Načini rada:

• Način grijanja: Ako je Start Temperature postavljeno je ispod the Temperatura zaustavljanja, the controller will operate in heating mode. The appliance will turn on when the actual temperature drops below the set start temperature and turn off when it reaches the set stop temperature.
• Način hlađenja: Ako je Start Temperature postavljeno je iznad the Temperatura zaustavljanja, the controller will operate in cooling mode. The appliance will turn on when the actual temperature rises above the set start temperature and turn off when it drops to the set stop temperature.

Kalibracija temperature:

The device supports temperature calibration within a range of ±9℃. Specific instructions for calibration are not provided in this manual. If precise calibration is required, please contact customer support for detailed guidance.

7. Održavanje

• Čišćenje: Obrišite uređaj mekom, suhom krpom. Nemojte koristiti abrazivna sredstva za čišćenje ili otapala.
• Skladištenje: Uređaj čuvajte na hladnom i suhom mjestu, dalje od izravne sunčeve svjetlosti i ekstremnih temperatura kada se ne koristi.
• Njega sonde: Ensure the temperature probe is kept clean and free from debris for accurate readings. Avoid bending or damaging the probe cable.

8. Rješavanje problema

If you encounter issues with your temperature controller, refer to the following common troubleshooting steps:

• Uređaj se ne uključuje:
  • Check if the power plug is securely inserted into a live power outlet.
  • Provjerite radi li utičnica ispravno.
• Appliance Not Activating/Deactivating:
  • Ensure the appliance is correctly plugged into the controller's outlet and is powered on.
  • Check if the set start and stop temperatures are appropriate for your desired heating or cooling mode.
  • Verify that the temperature probe is properly connected and positioned.
• Netočna očitanja temperature:
  • Ensure the temperature probe is clean and undamaged.
  • Verify the probe is fully immersed or positioned correctly in the environment being measured.
  • Consider if temperature calibration is needed (refer to Section 6).

Ako problemi potraju i nakon što ste pokušali ove korake, obratite se korisničkoj podršci.

9. Jamstvo i podrška

Za informacije o jamstvu ili tehničku podršku, molimo pogledajte pakiranje proizvoda ili se izravno obratite proizvođaču. Sačuvajte račun kao dokaz o kupnji.