Hotpoint NTM10 81WK Freestanding Tumble Dryer THANK YOU FOR BUYING A HOTPOINT PRODUCT. In order to receive more…
In order to receive more complete assistance, please register your product on www.hotpoint.eu/register
Remove all the tapes used to hold items on the machine. Before you use it, clean the inside of the drum to remove any dust that could have accumulated during transport. A slight odor or vapor may be found if you open the door during its first use, this is normal and should only last a few minutes. Make sure that the water tank is correctly inserted. Make sure that the drain hose on the back of the dryer is properly connected, either to the dryer’s water tank or to your domestic drainage system. The dryer must be installed in a room with a temperature ranging between 5°C and 35°C to ensure proper operation.
Laundry can be checked while the drying cycle runs and any garments already dry can be removed, while drying continues for the remaining items. After closing the door, press the “Start/Pause” button to resume machine operation.
Doing this will keep your machine working at its BEST:
Refer to the Care & Maintenance section.
Never lift the dryer by holding on to its top side.
Always check the care labels, especially when placing garments in the tumble dryer for the first time. Below are the most commonly used symbols:
|May be tumble dried|
|Do not tumble dry|
|tumble dry – high heat.|
|Tumble dry – low heat.|
The duration of these programs will depend on the size of the load, types of textiles, the spin speed used in your washer, and any extra options selected. In machines equipped with a display, the duration of the cycles is shown on the control panel. The remaining time is constantly checked and adjusted during the drying cycle to show the best possible estimate. Option to use – If all your loads on Automatic Cycles are consistently less dry or drier than you would like, you may increase or decrease the dryness level using the specific option.
This is the most efficient program in terms of energy consumption and is suitable for drying normal wet cotton laundry values on the Energy Label are based on this program. NOTE: For optimal energy efficiency, select “Cupboard Dry” using the dryness level option. To increase the dryness level, select “Extra D r y ”.
This is a cycle using high heat, which has been proven to reduce household bacteria. This cycle is not recommended for all fabrics, use it only for heavyweight fabrics.
For drying sturdy cotton jeans-wear and garments, like denim, such as trousers and jackets.
A short program suitable for refreshing fibers and garments through the emission of fresh air. Do not use with garments that are still wet. It can be used on any load size but is more effective with small loads. It lasts about 20 minutes.
These buttons allow you to personalize the selected program according to personal requirements. Not all options are available for all programs. Some options may be incompatible with ones you have previously set; if so, you will be alerted by the buzzer and/or blinking indicators. If the option is available, the option indicator will stay on. The program may retain some options selected in previous drying cycles.
Press the related button several times to obtain a different level of residual moisture on garments. An indicator signals the level being selected.
This option allows you to delay the start of the cycle. Press the corresponding button several times to obtain the required delay. After having reached the max settable time, the option is reset by pressing the button again. An indicator on the control panel signals the time being selected. After having pressed the “Start/ Pause” button,the machine signals the time remaining to the start of the cycle. In case of door opening, press the “Start/Pause” button once the door has been closed.
This option allows setting the drying time. Press the corresponding button to set the required time for drying. An indicator on the control panel signals the time being selected.
This option activates a prolonged buzzer at the end of the cycle. Enable it if you do not think you will hear the normal sound at the end of the cycle. This option remains in memory if selected in the previous drying.
Enables a more gentle treatment of the laundry by reducing the drying temperature.
This option makes all machine controls inaccessible, except the “On/Off” button. When the machine is on:
This option adds a crease treatment at the end of the cycle by means of a periodic rotation of the drum (duration up to 10 hours). It is particularly suitable when it is not possible to remove the laundry as soon as the drying ends. If this option is used together with the “Start Delay”, the crease treatment is also added to the “Start Delay” phase. This option remains in memory if selected in the previous drying.
This option turns off all sounds of the control panel. Only warnings remain active. When the machine is on:
Enables quicker drying.
CARE AND MAINTENANCE
WARNING: Unplug the dryer during the cleaning and maintenance procedures.
Pull the container out of the dryer and empty it into a sink or other suitable drain, then place it back properly. Do not use the dryer without having inserted the container back in place.
Pull the filter out and clean it by removing the lint from the filter surface under running water or using a vacuum cleaner. For optimal performance, dry up the filter before inserting it back in place.
Do not use the dryer without having reinserted the filter in place.
Remove the door filter as described below:
The filter is an essential part of drying. It is intended to collect the lint formed during the drying process. If the filter is clogged, the air flow inside the dryer can become seriously affected: this will increase the drying time and energy consumption and could damage the dryer. If this procedure is not carried out properly, the dryer may not start.
Cleaning the condenser unit (see Fig. C).
Remove the condenser unit regularly (monthly) and clean off any fluff deposits from the plates by running cold water along its rear end. The light on after several cycles is just a reminder to carry on this activity periodically.
Removing the condenser:
Before using the appliance carefully read the Safety Instructions.
*MAX LOAD 8 kg (Dry load)
|off-mode (Po) – Watts||0.15|
|left-on mode (PI) – Watts||0.15|
|This is the most efficient program in terms of energy consumption and is suitable for drying normal wet cotton laundry. The values of the Energy Label are based on this program.||on|
*MAX LOAD 9 kg (Dry load)
|off-mode (Po) – Watts||0.15|
|left-on mode (P1) – Watts||0.15|
|*This is the most efficient program in terms of energy consumption and is suitable for drying normal wet cotton laundry. The values on the Energy Label are based on this program. The values reported in the table are obtained with the condensed water drained externally through the drain hose.|
Before contacting the After-sales Service, refer to the table below. Often the malfunctions are minor and can be solved in a few minutes.
|The tumble dryer does not turn on.||The plug is not inserted into the socket.||insert the plug into the socket|
|The plug is faulty.||Try to plug another appliance in the same socket. Do not use connecting electrical devices to the socket, such as adapters or extensions.|
|A power failure occurred.||Wait for the power supply to be restored and switch the fuse on again if necessary.|
|The tumble dryer does not start.||The door has not been closed properly.||Close the door.|
|A time delay was set to the start of the cycle.||For machines equipped with this function: wait for the set delayto end or switch the machine off to reset K. Refer to the Options section.|
|The “Start/Pause” button was not pressed in order to start the program.||Press the “Start/Pause” button.|
|The Key Lock function was enabled (for machines equipped with this option).||Refer to the Options section and if Key Lock was selected, disable it. Switching the machine off is not enough to disable this option.|
|Garments are wet at cycle completion.||Small bad.||The automatic program has not sensed the required final moisture so the dryer completes the program and stops. If this happens simply select an additional short period of drying or select the extra dry option if available.|
|Large loads or heavier fabrics||Dryness levels can be modified to the specific dryness desired. Extra Dry Is recommended for ready-to-wear Items.|
|The drying times are very long.||Appropriate maintenance was not carried out||Refer to the Care & Mai ntenace section and perform the operations described.|
|The program, the time, and/or the d Ding level set are not suitable for the type and the amount of load inserted into the dryer.||Refer to the Programmes and Options sections to find the program and options most suitable for the type of load.|
|The garments are too wet.||Carry out a washing cycle with a higher spin speed to remove as much water as possible.|
|The dryer may be overloaded.||Refer to the Programmes section to check the max load for each program.|
|The program did not end.||A power failure might have occurred.||In case of power failure, it is necessary to press the “Start/Pause” button to restart the cycle.|
|Drum – slight odor or vapor.||A slight odor or vapor may be found if you open the door during its first use.||This is normal and should only last a few minutes.|
|Lights on or flashing|
|Water tank||The water tank is full. Empty the water tank. Refer to the Care & Maintenance section.|
|Door filter |
|Clean the door filter and check whether air intake is free. Carrying Failure of the airflow necessary for machine operation. out these operations improperly may cause damages. Refer to Care& Maintenance section.|
|The condenser unit requires cleaning. |
The light on is not a malfunction but just a reminder to carry on this activity periodically (monthly).
|Clean the condenser unit Refer to Care & Maintenance section.|
|The presence of the wrench symbol signals a malfunction.||The machine sensors detected a failure.||Switch the dryer off and unplug it. Open the door immediately and pull the laundry out, to allow the heat to dissipate. Wait for about 15 minutes. Reconnect the dryer to the power supply, load the laundry and restart the drying cycle. If the problem still occurs, contact the After-Sales Service Centre and communicate the letters and digits flashing on the display. For instance: F3 and U|
Policies, standard documentation, ordering of spare parts, and additional product information can be found by:
• Visiting our website docs.Hotpoint.EU and parts-selfservice.whirlpool.com
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-sales Service, please state the codes provided on your product’s identification plate.
|Hotpoint H3 D91GS Freestanding Tumble Dryer [pdf] User Guide|
H3 D91GS Freestanding Tumble Dryer, H3 D91GS, Freestanding Tumble Dryer
KSW1081 Monroe Tail Sconce Installation Instructions for Monroe Tail Sconce MONROE-WALL KSW1081, KSW1091, KSW1102 1.0…
P944353 Freecom 4x Communication System communication in motion FREECOM 4x POCKET GUIDE EN/ES/JP/CN Getting Started…
975HR Rosemount 975 Flame Detectors RosemountTM 975 Pole Mount Quick Start Guide 00825-1200-4975, Rev AA…
GC-COM-1000-X6 Growcraft X6 1000W LED Grow Light Growcraft Commercial Instructions Now that you've received your…
PR-34041-HPHNM Pressure Injectable One-Lumen PICC with 80 cm Wire PR-34041-HPHNM 4 1 Fr. Lumen 40…