Superior-Life-LOGO

Superior Life Direct Wire LED Sign Linear T8

Superior-Life-Direct-Wire-LED-Sign-Linear-T8-PRODUCT

INSTALL cov lus qhia

PLEASE FIND A QUALIFIED ELECTRICIAN FOR INSTALLATION. Please read the instructions before you install and use the linear tube(s).

NYEEM THIAB UA RAWS LI TXHUA COV KEV RUAJ NTSEG

DANGER – RISK OF SHOCK – DISCONNECT POWER BEFORE INSTALLATION.

  • CEEB TOOM – Risk of fire or electric shock. LED Retrofit kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation and contact a qualified electrician.
  • CEEB TOOM – Risk of fire or electric shock. Product must be installed in accordance with the national electrical code or your local electrical code. If you are not familiar with these codes and requirements, contact a qualified electrician.
  • CEEB TOOM - Kev pheej hmoo ntawm hluav taws kub lossis hluav taws xob poob siab. Nruab cov khoom siv no tsuas yog hauv cov luminaires uas muaj cov yam ntxwv ntawm kev tsim kho thiab qhov ntev uas pom hauv cov duab thiab / lossis cov duab kos thiab qhov chaw nkag ntawm cov khoom siv retrofit tsis pub dhau qhov kev ntaus nqi ntawm lub luminaire.
  • CEEB TOOM – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
  • CEEB TOOM – To avoid potential fire or shock hazard, do not use this retrofit kit in luminaires employing shunted bi-pin lampcov tuav. Lus Cim: Sunted lamp Cov tuav tau pom tsuas yog hauv fluorescent luminaires nrog Instant-Start ballasts. Instant-start ballasts tuaj yeem txheeb xyuas los ntawm cov lus "Instant Start" lossis "IS" cim ntawm lub ballast. Qhov kev xaiv no yuav yog nyob rau hauv daim ntawv ntawm cov lus hais txog lub ballast nws tus kheej, los yog tej zaum yuav ua ke nrog cov cim rau lamps uas lub ballast yog npaj los siv, example F40T12/IS. Yog xav paub ntxiv, hu rau LED luminaire retrofit khoom tsim khoom.
    Cov neeg teeb tsa yuav tsum tsis txhob txuas cov xov hlau uas twb muaj lawm los ntawm lamptuav cov dav hlau los ua kev sib txuas tshiab ntawm lampcov terminals. Hloov chaw installers yuav tsum txiav uas twb muaj lawm lamptus tuav coj mus deb ntawm lamptus tuav thiab ua hluav taws xob sib txuas tshiab rau lamptuav cov xov hlau los ntawm kev siv cov txuas txuas.
  • CEEB TOOM – Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when installing of retrofit kit hardware. Check for enclosed wiring and components.
  • CEEB TOOM – Risk of fire or electric shock. Check the existing wiring for damage before installing upgrade kit. Do not install if existing wires are damaged. The retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction. Product must be installed by a qualified electrician in accordance with the applicable and appropriate electrical codes. The installation guide does not supersede local or national regulations for electrical installation. “This luminaire has been modified and can no longer operate the originally intended lamp,’’ shall be marked on the retrofit luminaire where readily visible by the user during normal maintenance including re lamphauv. Tsis txhob siv nrog dimmers. Haum rau damp qhov chaw. Haum rau cov luminaires kaw. Cov cuab yeej no tsis yog tsim los siv nrog cov khoom siv thaum muaj xwm txheej ceev.
  • CEEB TOOM – Disconnect power or circuit breaker before installing or servicing.

IB TUG TXIV TUB CEEV TSEEM CEEB

  1. Make sure the circuit breaker that supplies the power to the fixture is turned off.
  2. Remove lens or diffuser cover (if applicable) and existing fluorescent lamps.
  3. Open/Remove ballast wiring compartment cover.
  4. Identify the line and neutral wires running from the breaker box to the ballast and confirm the power is off using a voltmeter.
  5. Cut all wires connected to ballast, and remove ballast (and starter if present). Dispose of removed ballast and fluorescent lamps raws li tsoomfwv cov cai hauv koj cheeb tsam.
  6. Ensure that the fixture contains R17d lamp cov tuav.
  7. Make sure all sockets are replaced and wired according to the appropriate wiring diagram. (Figure 1, 2, 3, 4 – on Page 2).
  8. Reinstall the ballast cover to hide all wires.
  9. Install your new LED single ended T8 replacement lamps. These LED T8 lamps yog tsim los rau ib qho kev sib txuas txuas nkaus xwb. Thaum txhim kho, paub meej tias tsuas yog cov tswv yim kawg ntawm lamp yog powered, thiab ruaj ntseg txuas nrog lub powered R17d lamp cov tuav.
  10. Apply Re-lamping Label on a visible location inside the fixture.
  11. Reinstall lens or diffusion cover on the light fixture.
  12. Turn power on at the breaker box.
  13. Tig rau lub teeb.

IB TUG TXIV TUB CEEV TSEEM CEEB

Non-shunted Sockets

CEEB TOOM – Disconnect power or circuit breaker before installing or servicing.

RETROFIT nrog IB LAMP

Superior-Life-Direct-Wire-LED-Sign-Linear-T8-FIG-1

RETROFIT nrog ob LAMPS

Superior-Life-Direct-Wire-LED-Sign-Linear-T8-FIG-2

RETROFIT nrog peb / plaub LAMPS

Superior-Life-Direct-Wire-LED-Sign-Linear-T8-FIG-3

RETROFIT nrog peb / plaub LAMPS & OB BALLASTS

Superior-Life-Direct-Wire-LED-Sign-Linear-T8-FIG-4

PREMIUM QUALITY LIGHTING®

Specifications yuav hloov tsis tau ceeb toom. Cov duab thiab kab kos duab yuav tsis yog qhov ntsuas thiab tsuas yog siv rau kev siv dav dav xwb.

Cov ntaub ntawv / Cov ntaub ntawv

Superior Life Direct Wire LED Sign Linear T8 [pdf] Installation Guide
Direct Wire LED Sign Linear T8, Direct Wire T8, LED Sign Linear T8, Linear T8, LED Sign T8, T8 LED, LED, T8

References

Cia ib saib

Koj email chaw nyob yuav tsis tsum luam tawm. Yuav tsum tau teb cov cim *