Instruction Manual for PHILIPS models including: DDNG232 RS-232 Gateway, DDNG232, RS-232 Gateway, Gateway
2 giorni fa — 根据国家/地区及当地的电气与建筑规范和法规，该设. 备必须由有资质的电工安装在经批准的外罩内。 DDNG232. RS-232 Gateway ... RS-232. DDNG232. TX/RX. RTS/CTS. RX/TX.
File Info : application/pdf, 2 Pages, 1.19MB
DocumentDocumentDDNG232 RS-232 Gateway Installation Instructions Instructions d'installation Installationsanweisungen Instrucciones de instalación Istruzioni per l'installazione Installatie-instructies Devices must be installed in an approved enclosure by a qualified electrician in accordance with all national and local electrical and construction codes and regulations. Les appareils doivent être installés dans un lieu jugé apte, par un électricien qualifié et conformément aux règles et normes locales et nationales en matière d'électricité et de construction. Die Geräte müssen von einem geprüften Elektriker entsprechend allen nationalen und lokalen Elektro und Bauvorschriften in einem zugelassenen Gehäuse installiert werden. Los dispositivos se deben instalar en un recinto aprobado por un electricista cualificado de acuerdo a todos los reglamentos eléctricos y de construcción locales y nacionales pertinentes. I dispositivi devono essere installati da un elettricista qualificato in un luogo approvato, in conformità a tutti gli standard e le norme nazionali e locali vigenti in materia di impianti elettrici e costruzioni edilizie. Apparaten moeten door een erkende elektricien worden geïnstalleerd in een goedgekeurde behuizing in overeenstemming met alle nationale en lokale elektriciteits en bouwvoorschriften en wetgeving. / 94 mm (3.70 in) 1 IEC Pollution Degree II RJ12 211 mm (8.31 in) 75 mm (2.95 in) 45 mm (2 in) 50° C (122° F) 0° C (32° F) 90% 45 mm (2 in) RS-232 DB9 Female socket 2 L 240 V N 0.1 A E 9 - RI 8 - CTS 7 - RTS 6 - DSR 5 - SG 4 - DTR 3 - RD 2 - TD 1 - DCD µP DCE / DTE Selector 3 DDNG232 12 V 90 mA RJ12 AUX +12 V D D + GND SHLD RS-485 DyNet MODEM TX/RX RX/TX COMPUTER RTS/CTS CTS/RTS DCE/DTE RS-232 IEC Overvoltage Category III 4 5 4 mm2 11+ AWG SHLD GND D+ D- +12V AUX RJ12 6 RS-485 DyNet SHLD GND D+ D+12 V AUX +12V +12V DD+ GND GND RS-485 DyNet RS-485 DyNet 2 A 0.3-2.5 mm2 GND AUX 22-12 AWG <20 m 0.4 Nm 3.5 Lb-in This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures. © 2023 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners. www.dynalite.com AZZ 408 0823 R19