Philips Global Consumer Care - Royal Philips Electronics
Philips Customer Service Support - Home | Philips
User Manual for PHILIPS models including: TAA7507, 7000 Series Sports Wireless Headphones, Sports Wireless Headphones, Wireless Headphones, Sports Headphones, Headphones
Philips TAA7507 GO Black
Philips True Wireless Sports Headphone TAA7507BK/00 Tech-America
Philips True Wireless Sports Headphone - antonline.com
File Info : application/pdf, 20 Pages, 1.49MB
DocumentDocumentSports Headphones 7000 Series TAA7507 User manual Register your product and get support at www.philips.com/support Contents 1 Important safety instructions 2 Hearing safety 2 General information 2 2 Your True wireless earpieces 4 What's in the box 4 Other devices 4 Overview of your True wireless earpieces 5 3 Get started 6 Charge the battery 6 How to wear 7 App download 7 Pair for the rst time 7 Pair with another Bluetooth device 8 4 Use your earpieces 9 Connect to your Bluetooth device 9 Control ANC (Active Noise Cancelation) 9 Power on/off 10 Manage your calls and music 10 Voice Assistant 10 Earpieces LED indicator status 10 Charging box LED indicator status 11 5 Reset the earpieces 12 6 Technical data 12 7 Notice 13 Declaration of conformity 13 Disposal of your old product and battery 13 Remove the integrated battery 13 Compliance with EMF 14 Environmental information 14 Notice of compliance 14 8 Trademarks 16 9 Frequently asked questions 17 1 Important safety instructions Hearing safety Danger To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headphones. · Listen at reasonable volumes for reasonable periods of time. · Be careful not to adjust the volume continuously upwards as your hearing adapts. · Do not turn up the volume so high that you can't hear what's around you. · You should use caution or temporarily discontinue use in potentially hazardous situations. · Excessive sound pressure from earpieces and headphones can cause hearing loss. · Using headphones with both ears covered while driving is not recommended and may be illegal in some areas. · For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments. 2 EN General information To avoid damage or malfunction: Caution Do not expose headphones to excessive heat. Do not drop your headphones. Headphones shall not be exposed to dripping or splashing. (Refer to the IP rating of specic product) Do not allow your headphones to be submerged in water. Do not charge your headphones when the connector or socket is wet. Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives. Use a clean, damp cloth to clean your headphones - especially the sound conduits and the microphone holes - regularly and avoid buildup of substances such as sweat or earwax. If any sweat or water droplets are left in the sound conduits, air holes or microphone holes, the sound level will temporarily drop or cut out entirely. This is not a malfunction. Use a soft, damp cloth to dry the headphones thoroughly. Alternatively, remove the earbud tips, turn the sound conduits downward and gently tap the headphones about ve times on a dry cloth or similar to remove any water collected inside. Be sure the headphones are completely dry before charging and using. Avoid using disposable alcohol pads or other substances for cleaning. The integrated battery shall not be exposed to excessive heat such as sunshine, re or the like. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. To achieve the specic IP rating, the charging slot cover must be closed. Disposal of a battery into re or a hot oven, or mechanically crushing or cutting a battery, can result in an explosion. Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of ammable liquid or gas. A battery subjected to extremely low air pressure may result in an explosion or the leakage of ammable liquid or gas. Replacement of a battery with an incorrect type risks severely damaging the headphones and the battery (for example, in the case of some lithium battery types). If the headset is not used for a long time, the rechargeable battery will begin to lose its charge. To avoid this loss, please fully charge the battery at least once every three months. To avoid risk of re, the equipment is supplied only by external power source which output shall comply with PS1 (with output capacity less than 15W). Operating and storage temperatures and humidity · Store in a place where the temperature is between -20°C (-4°F) and 50°C (122 °F) with up to 90% relative humidity. · Operate in a place where the temperature is between 0°C (32°F) and 45°C (113 °F) with up to 90% relative humidity. · Battery life may be shorter in high or low temperature conditions. 3 EN 2 Your True wireless earpieces USB-C charging cable (for charging only) Congratulations on your purchase, and welcome to Philips! To fully benet from the support that Philips offers, register your product at www.philips.com/support. With these Philips True wireless earpieces you can: · Enjoy convenient wireless handsfree calls · Enjoy and control music wirelessly · Switch between calls and music Quick start guide Warranty What's in the box Safety leaet Philips True wireless earpieces Philips TAA7507 Stablizers x 6 + Eartips x 6 Lanyard 4 EN Other devices A mobile phone or device (e.g. notebook, tablet, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible with the earpieces. Overview of your True wireless earpieces 1 2 3 4 5 6 1 LED indicator (earpieces) 2 Multi-function touch (MFT) 3 Bluetooth pair button 4 LED indicator (BT pairing and factory reset) 5 LED indicator (battery state or charging state) 6 USB-C charging slot 5 EN 3 Get started Charge the battery Note Before you use your headphones, place them in the charging box and charge the battery for 2 hours for optimum battery capacity and lifetime. Use only the original USB-C charging cable to avoid any damage. Finish your call before charging. Connecting the earpieces to charge will power them off. Earpieces Place the earpieces in the charging box. · The earpieces start charging and the blue LED light goes on · When the earpieces are fully charged, the blue light will go off Charging Box Plug one end of the USB-C cable into the charging box and the other end into the power source. Tip Normally, a full charge takes 2 hours (for the earpieces or charging box) by USB cable. Tip The charging box serves as a portable backup battery for charging the earpieces. When the charging box is fully charged, it will fully recharge the earpieces 3 times. 6 EN How to wear Select suitable ear tips for optimum t A tight, secure t will provide the best sound quality and noise-cancellation. 1 Test which ear tips and stabilizers provides you with the best sound and wearing comfort. 2 3 sizes of silicone ear tips and stabilizers are provided : large, medium, small. L M S App download Scan the QR code/press 'Download' button or search 'Philips Headphones' in Apple App Store or Google Play to download the app. The Philips Headphones App put you in charge of the music you've listening to. You can customize the sound so your music and calling experience always best suits your needs. Insert the earpieces 1 Check left or right orientation of the earpieces. 2 Insert the earpieces into the ears and twist slightly until a secure t is achieved. Pair the earpieces with your Bluetooth device for the rst time 1 Make sure that the earpieces are fully charged and powered off. 2 Open the cover of the charging box, the earpieces will be in pairing mode and ready to connect. The LEDs on both earpieces ash white and blue alternately The earpieces are now in pairing mode and are ready to pair with a Bluetooth device (e.g. a mobile phone) 7 EN 3 Turn on the Bluetooth function of your Bluetooth device. 4 Pair the earpieces with your Bluetooth device, refer to the user manual of your Bluetooth device. Note After powering on, if the earpieces cannot nd any previously connected Bluetooth device, it will automatically switch to pairing mode. The following example shows you how to pair the earpieces with your Bluetooth device. 1 Turn on the Bluetooth function of your Bluetooth device, select Philips TAA7507. 2 Enter the earpieces' password "0000" (4 zeros) if prompted. For those devices featuring Bluetooth 3.0 or higher, there is no need to enter a password. Philips TAA7507 Single earpiece (Mono mode) Take either right or left earpiece out from charging box for Mono use. The earpiece will power on automatically. You will hear a voice from the earpieces saying "Power on". Note Take the second earpiece from the charging box and they will pair with each other automatically. 8 EN Pair the earpieces with another Bluetooth device If you want to pair another Bluetooth device with the earpieces, just put them into pairing mode, (press button on box for 3 seconds with both earpieces inside and the cover open), then discover the second device as per normal pairing. 03" Note The earpieces store 4 devices in the memory. If you try to pair more than 4 devices, the earliest paired device is replaced by the new one. Multi-point connection Pairing · Pairing the headphones to 2 devices, e.g. mobile phone and notebook. Switch between device · At anytime, you can only listen to music from 1 device. Another device will be for phone call. · Pause the audio from 1 device and then start play audio from the another device. Note When streaming audio from Device 1, receiving a call from Device 2 will automatically pause Device 1 playback. And the call will be routed automatically to headphones. Ending the call will automatically resume playback from device 1. 4 Use your earpieces Connect the earpieces to your Bluetooth device 1 Turn on the Bluetooth function of your Bluetooth device. 2 Open the charging box cover. The blue LED ashes. The earpieces will search the last connected Bluetooth device and reconnect to it automatically. If the last connected one is not available, the earpieces will search and reconnect to the second last connected device. Control ANC (Active Noise Cancelation) Enable ANC Different ANC modes can be toggled via double tapping on the right earpiece. · ANC function is automatically activated when earpiece is placed in the ear · Touch the MFT twice, it will change to awareness mode · Touch the MFT twice again, it will turn the ANC function off ANC Off Awareness mode ANC ON Tip If you turn on the Bluetooth function of your Bluetooth device after turning on the earpieces, you have to go to the Bluetooth menu of the device and connect the earpieces to the device manually. Note If the earpieces fail to connect to any Bluetooth device within 3 minutes, it will turn off automatically to save the battery life. In some Bluetooth devices, connection may not be automatic. In this case, you have to go to the Bluetooth menu of your device and connect the earpieces to the Bluetooth device manually. If no signal (music/call) is received for 60 mins even with Bluetooth connection, the earpieces will turn off automatically to save the battery life. Tip Removing the earpieces will automatically activate sleep mode. When you put the earpieces back they will return to active mode. Task ANC ON Awareness mode ANC OFF Quick awareness MFT Right earpiece Right earpiece Right earpiece Right earpiece Operation Double tap Double tap Double tap Continue touching after beep 9 EN Power on/off Task Turn the earpieces on MFT Turn the earpieces off Operation Take earpieces out of the charging box to power on Put earpieces back into the charging box to power off Manage your calls and music Music control Task Play or pause music Next track Adjust volume +/- MFT Right earpiece Right earpiece Operation Tap and hold 1 second Triple tap Via mobile phone control Call control Task MFT Pick up/ Switch caller during a call Hang up call/ Reject call Right earpiece Right earpiece Operation Double tap Tap and hold 1 second Voice Assistant Task Trigger Voice (Siri/Google) Assistant Stop Voice Assistant Button Left earpiece Left earpiece Operation Tap and hold 2 seconds Single tap Earpieces LED indicator status Earpieces status The earpieces are connected to a Bluetooth device The earpieces are ready for pairing The earpieces are on but not connected to a Bluetooth device Low battery level (earpieces) Battery is fully charged (charging box) Indicator White LED blinks every 5 seconds The LED ashes blue and white alternately White LED blinks every second (auto turn off after 3 minutes) Blue LED blinks 2x every 5 seconds Refer to case LED 10 EN Charging box LED indicator status When charging Battery low Relative adequate battery Indicator Amber LED lights up White LED lights up In use and cover is open Battery low Relatively adequate battery Indicator Amber slowly blinks for 4 cycles Off 11 EN 5 Reset the earpieces If you encounter any pairing or connection issue, you can follow the following procedure to reset your earpieces to factory default settings. 1 On your Bluetooth device, go to the Bluetooth menu and remove Philips TAA7507 from the device list. 2 Turn off the Bluetooth function of your Bluetooth device. 3 Return earpieces to charging box and open the lid. 4 Press button on box twice. 5 Follow steps in "Use your earpiecesconnect the earpieces to your Bluetooth device." 6 Pair the earpieces with your Bluetooth device, select Philips TAA7507. If there is no response from the earpieces, you can follow the below step to reset the hardware of your earpieces. Tap and hold multi-function touch for 10 seconds. 6 Technical data Music play time (ANC on) : 7 + 21 hours Music play time (ANC off) : 8 + 24 hours Standby time: 200 hours Charging time: 2 hours Lithium-ion battery 55 mAh on each earpiece, Lithium-ion battery 500 mAh on charging box Bluetooth version: 5.2 Compatible Bluetooth proles: · HFP (Hands-Free Prole) · A2DP (Advanced Audio Distribution Prole) · AVRCP (Audio Video Remote Control Prole) Supported audio codecs: LDAC, AAC, SBC Frequency range: 2.402-2.480 GHz Transmitter power: < 10 dBm Operation frequency: 110-205kHz Max. H-eld strength: 11.3 dBuA/m (62.8 dBuV/m) Operating range: Up to 10 meters (33 feet) Auto power off USB-C port for charging Wireless charging Low battery warning: available Note Specications are subject to change without notice. 12 EN 7 Notice Declaration of conformity Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can nd the Declaration of Conformity on www.p4c.philips.com. Disposal of your old product and battery Remove the integrated battery If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing of the earpieces. · Make sure the earpieces are disconnected from the charging box before removing the battery. Your product is designed and manufactured with high quality materials and components which can be recycled and reused. This symbol on a product means that the product is covered by European Directive 2012/19/EU. · Make sure the charging box is disconnected from the USB charging cable before removing the battery. This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an official collection point or a Philips service centre to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health. 13 EN Compliance with EMF This product complies with all applicable standards and regulations regarding exposure to electromagnetic elds. Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. Notice of compliance The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. FCC rules This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, 14 EN if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the separation between equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Caution: The user is cautioned that changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Canada: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) L'appareil ne doit pas produire de brouillage; (2) L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. CAN ICES-003(B)/NMB-003(B) IC Radiation Exposure Statement: This equipment complies with Canada radiation exposure limits set forth for uncontrolled environments. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. 15 EN 8 Trademarks Bluetooth The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners. Siri Siri is a trademark of Apple Inc., registered in the U.S. and other countries. Google Google and Google Play are trademarks of Google LLC. 16 EN 9 Frequently asked questions My Bluetooth earpieces do not turn on. The battery level is low. Charge the earpieces. I cannot pair my Bluetooth earpieces with my Bluetooth device. The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the earpieces. Pairing does not work. · Put both earpieces into charging box. · Make sure you have disabled the Bluetooth function of any previously connected Bluetooth devices. · On your Bluetooth device, delete "Philips TAA7507" from the Bluetooth list. · Pair your earpieces (see `Pair the earpieces with your Bluetooth device for the rst time' on page 7). The Bluetooth device cannot nd the earpieces. · The earpieces may be connected to a previously paired device. Turn off the connected device or move it out of range. · Pairing may have been reset or the earpieces have been previously paired with another device. Pair the earpieces with the Bluetooth device again as described in the user manual. (see `Pair the earpieces with your Bluetooth device for the rst time' on page 7). My Bluetooth earpieces are connected to a Bluetooth stereo-enabled mobile phone, but music only plays on the mobile phone speaker. Refer to the user manual of your mobile phone. Select to listen to music through the earpieces. The audio quality is poor and a crackling noise can be heard. · The Bluetooth device is out of range. Reduce the distance between your earpieces and Bluetooth device, or remove obstacles between them. · Charge your earpieces. The audio quality is poor when streaming from a mobile phone is very slow or streaming does not work at all. Make sure your mobile phone not only supports (mono) HFP but also supports A2DP and is BT4.0x (or higher) compatible (see `Technical data' on page 12). Clean your headphones regularly. · Use a clean, damp cloth to clean your headphones - especially the sound conduits and the microphone holes regularly and avoid buildup of substances such as sweat or earwax. · If any sweat or water droplets are left in the sound conduits, air holes or microphone holes, the sound level will temporarily drop or cut out entirely. This is not a malfunction. Use a soft, damp cloth to dry the headphones thoroughly. Alternatively, remove the earbud tips, turn the sound conduits downward and gently tap the headphones about ve times on a dry cloth or similar to remove any water collected inside. · Be sure the headphones are completely dry before charging and using. Avoid using disposable alcohol pads or other substances for cleaning. 17 EN Charge your headphones regularly. If the headset is not used for a long time, the rechargeable battery will begin to lose its charge. To avoid this loss, please fully charge the battery at least once every three months. 18 EN 2022 © MMD Hong Kong Holding Limited. All rights reserved. Specications are subject to change without notice. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product. All other company and product names may be trademarks of its respective companies with which they are associated. UM_TAA7507_00_EN_V2.0 Model: TAA7507CA