Best Video Lights | Lights for Video Studio | COLBOR
User Manual for COLBOR models including: CL330 Video Light, CL330, Video Light, Light
30 gen 2024 — 6160. 572. 2030. 188. 6190. 575. 5m. 3m. CCT. 2700K. 3200K. 4300K. 5600K. 6500K. The data is given from testing in a laboratory baesed on BHR45. Page 18. Room ...
RATE: Lv.1 - Lv.5. DIM: 0%-100%. CCT: 2700K-6500K. G/R：Green 10~1 - 0 - Red 1 ... (not included in CL330M Lite). Warranty Card x1. Page 17. Form 1.
File Info : application/pdf, 18 Pages, 1.20MB
DocumentDocumentCL330 Video Light User Manual Thank you for choosing COLBOR product. Please read this manual carefully before use and follow all instructions mentioned herein. Caring For Your COLBOR Product Keep corrosive chemicals, liquids and heat source away from the product to prevent mechanics damage. The product is not waterproof. Do not leave the product unattended while in use. Keep out of reach of children. Do not handle with wet hands. Do not touch the hot COB surface. Please do not block the ventilation and do not look at the light directly when it is on. Do not attempt to disassemble or modify the product. Doing so voids warranty. Please have the product checked or repaired by authorized technicians if any malfunctions happened. Disconnect from the power supply when it is not in use. Do not cover, inverted COB and radiator for high temperature, do not cover, inverted, do not touch the lamp holder and radiator vent with your hands when the product in use. Do not use any power adapter of other products to avoid the lamp malfunction. Malfunction may be caused by dropping, impact of external force. Failure to follow all the instructions may result in mechanics damage. Our company reserves the right of final interpretation of the product. Product design and specifications are subject to change without prior notice. Power Connection You must use the power adapter that comes with the product rather than other adapters to avoid damaging the lamp. The positive and negative connections of the power adapter interface( DC OUT) and the lamp power interface (DCIN) are shown below: + -- + N N Product Instructions LED Display Screen EFF Mode Button EFF Rate Option Button CCT Mode Button Settings Button Option Adjustment Knob Parameter Adjustment Knob/ Parameter Preset DC 48V Power Port Power Button Bowens Mount COB Lamp Beads Lamp Angle Adjustment Locking Grip Bracket Air Outlet NATO Slideway Air Inlet Lamp Grip Soft Light Cover Hole Soft Light Cover Hole Screws Bracket Screw Light Installation 1. Removal of lamp cap protection cover Hold the COB cover with the Bowens Mount tenon and rotate it as the direction of the arrow. Note: Be sure to remove COB protective cover and COB protective film before use. 2. Installation and removal of reflector Installation of reflector: Align the reflector with the groove around the lamp head and clip it in, turn the reflector as the direction of the arrow, and the reflector installation will be completed after the top rod rebounds. Removal of reflector: Under the instructions of "Lamp Cap Protection Cover Removal". 3. Installation and fixation of light Rotate the lamp holder screw until the inner wall not shielded and put the product on the top of the lamp holder to tighten the bracket screw for fixation. Adjust the lamp body irradiation Angle and tighten the lamp holder Angle grip fixed. Screw out, the inner wall of the bracket without any shelter Halfway the screw out The screw is not out at all 4. Install the soft light cover Insert the handle of the soft light umbrella into the umbrella hole. After adjustment, lock the cover hole screw. Screw out, the inner wall of the soft light cover without shelter The screw is not out at all 5. Power Connection (1) Mount the power adapter Do not suspend the power adapter in the air. Use wire rings to hang it on the lamp stand. (2) Power with power adapter Connect the power adapter, align the pin with the DC power interface of the lamp body, and then power through the cable after stable. (3) Power cord storage Please turn off the lamp before unplugging the power cord. When unplug the power cable, hold down the safety lock on the connector before removing it. If unlocked, do not forcibly remove the power supply. (4) Power with V-port battery Mount the V-port battery to the lamp by complimentary the NATO expansion bar with VM3 (optional), and then connect the D-tap to XLR power cable to start the lamp. Note: *Under the condition of one 14.8V battery power supply, the maximum brightness of the product is 60% of the full power. *When the battery capacity is insufficient, the brightness of the product light will be adapted to reduce the power to avoid the danger of overheating of the power cord due to excessive current. * It is recommended to use the dual V battery power supply. Operation Instructions 1. Please remove the COB protective cover before using the light. 2. Turn on the lamp: After confirming that the power connection is normal, press the switch to "-", and the screen will display the brand and product module, and then enter the operation interface. (Default mode: CCT) 3. Turn off the lamp: press the switch to "o" to turn off the power switch. 1. Status Icon Description APP Connection Status Icon After selecting wireless connection in Settings menu, the icon will be displayed dynamically. The icon is always on to indicate successful pairing with mobile APP. The icon disappears to indicate mobile APP pairing failure, or the product is unpaired. Fan Status Icon Smart Mode. The product will adjust the fan speed according to the internal detected temperature to ensure that it is in optimal working condition. Quiet Mode. The fan keeps running at low speed for minimum noise, and overheating protection will be activated if the product temperature is higher than the alarm value. Performance Mode. Fan runs at the highest speed to ensure heat dissipation. Group Status Icon None grouping status. The product defaults to the factory status, and will not be affected by other groups. A stands for Group A. There are fifteen groups (A~O). T stands for Tx. A stands for Group A. There are fifteen groups (A~O). R stands for Rx. A stands for Group A. There are fifteen groups (A~O). TR stands for TxRx. Product Overheated Alarm Icon If the icon flashes, it means that the internal temperature of the product is too high, and cooling measures need to be taken. If the icon disappears, it means that the operation is normal. 2. CCT Mode (Short press CCT Mode Button to enter) Color Temperature Brightness G/R Compensation CCT Mode Button Option Adjustment Knob Turn the knob clockwise or anti-clockwise to adjust options: color temperature, brightness, Chromatic Aberration Compensation. Parameter Adjustment Knob/Parameter Preset Turn the knob clockwise or anti-clockwise to adjust parameter of color temperature, brightness and Chromatic Aberration Compensation : Brightness (DIM): 0%~100% Color temperature: 2700-6500K Chromatic Aberration Compensation: Green10~1-0-Red1~10 Press down the knob to quickly switch the preset parameter of color temperature, brightness and Chromatic Aberration Compensation : Preset brightness0%25%50%75%100% Preset color temperature2700K3200K4000K5600K 6500K Chromatic Aberration Compensation: Short press return to zero Rolling the knob will enlarge the current setting parameter value, and it will automatically return to the main screen after 1.5 seconds of no operation. 3. EFF Mode (Short press EFF Mode Button to enter) EFF Mode Button Rate Option Button Special Effect Rate Color Temperature Brightness G/R Compensation Option Adjustment Knob Turn the knob clockwise or anti-clockwise to adjust options: color temperature, brightness, Chromatic Aberration Compensation.Knob left and right in the same direction can be rotated option Parameter Adjustment Knob/Parameter Preset Turn the knob clockwise or anti-clockwise to adjust parameter of color temperature, brightness and Chromatic Aberration Compensation : Brightness (DIM): 0%~100% Color temperature: 2700-6500K Chromatic Aberration Compensation: Green10~1-0-Red1~10 Press down the knob to quickly switch the preset parameter of color temperature, brightness and Chromatic Aberration Compensation : Preset brightness0%25%50%75%100% Preset color temperature2700K3200K4000K5600K 6500K Chromatic Aberration Compensation: Short press return to zero Light Effect Mode (EFF) Button Press to switch light effect: Fire CCT Chase Pulsing Pulsing TV Explosion Faulty Bulb Welding Strobe Lightning S.O.S RATE: Lv.1 - Lv.5 DIM: 0%-100% Fire CCT: 2700K-6500K G/RGreen 10~1 - 0 - Red 1~10 CCT Chase Pulsing RATE: Lv.1 - Lv.5 DIM: 0%-100% CCT: LOCK G/RGreen 10~1 - 0 - Red 1~10 RATE: Lv.1 - Lv.5 DIM: 0%-100% CCT: 2700K-6500K G/RGreen 10~1 - 0 - Red 1~10 RATE: Lv.1 - Lv.5 DIM: 0%-100% TV CCT: LOCK G/RGreen 10~1 - 0 - Red 1~10 RATE: Lv.1 - Lv.5 DIM: 0%-100% EFF Explosion CCT: 2700K-6500K G/RGreen 10~1 - 0 - Red 1~10 RATE: Lv.1 - Lv.5 DIM: 0%-100% Faulty Bulb CCT: 2700K-6500K G/RGreen 10~1 - 0 - Red 1~10 RATE: Lv.1 - Lv.5 DIM: 0%-100% Welding CCT: 2700K-6500K G/RGreen 10~1 - 0 - Red 1~10 Strobe RATE: Lv.1 - Lv.5 DIM: 0%-100% CCT: 2700K-6500K G/RGreen 10~1 - 0 - Red 1~10 Lightning RATE: Lv.1 - Lv.5 DIM: 0%-100% CCT: 2700K-6500K G/RGreen 10~1 - 0 - Red 1~10 S.O.S RATE: LOCK DIM: 0%-100% CCT: 2700K-6500K G/RGreen 10~1 - 0 - Red 1~10 4. Setting 1. Short press the setting botton to enter settings menu. 2. Turn the brightness control knob clockwise or anti-clockwise to choose setting. 3. Press the setting botton to adjust corresponding setting (Short press the setting botton to adjust the wireless connection mode). Settings Wireless Connection Fan Mode Options APP/Remote Control Long press the setting button for pairing (One mode for each time SMART/ QUIET/ PERFORMANEC SMART: The product will detect the current internal temperature to adjust the fan speed by itself. QUIET: The fan will run at low speed. If the product temperature reaches the alarm value, it will start the power-off protection mechanism. PERFORMANEC: Fan runs at the highest speed to ensure heat dissipation. Group NULL/ A~O (NULL by default) Communication TX/ RX/ TXRX (TX by default) Curve LINEAR, L.CURVE, E.CURVE, S.CURVE. Response Initial brightness setting Language SHARP/ SMOOTH (SMOOTH by default) Default0%25%75%100% EN/ CN Product INFO. Short press the setting botton to enter the production information interface. Press the setting botton again to go back to settings menu. Hardware Version Firmware Version Protocol Version MAC Address 5. APP Connection & Light Control Scan the QR codeor search "COLBOR STUDIO" in app store to download the app for light control. CL330 Pairing: 1. Press the settings button and enter the pairing mode. Short press the settings button to choose "APP", then long press the settings button for 3 seconds for pairing. 2. Open the APP and click the " + " on the upper right, then click the scene one and click the + on the upper right. Showing CL330 means successfully pairing. 3. Click the CL330 for control. CL330 Group Control: 1. After successfully pairing the CL330, click the group then click the" + " on the top right. Choose the light for grouping and click the confirm bottom. Showing Group One means successfully grouping. 2. Click the group for lighting control. Equipped with a NATO extension bar and an NQD quick-release device, the lights can be spliced together, and up to three lights can be spliced. Specifications Color Rendering Index Color Temperature Range Beam Angle Illumination COB Output Power Power Light Working Voltage Cooling Mode Connector Body Material Light Dimension (mm) Light Weight Operating Temperature 97+ 2700K-6500K±200K G/R Compensation 120° Reflector 45° See the Form 1 Below 330W 360WMax DC 48V 7.5A SMART/ QUIET/PERFORMANEC Three core cannon head ( 2 for active, and 1 for negative) Aluminum Alloy+ ABS 299*128*232mmLight Base Included 2.07kgLight Base Included -10~40 Package List CL330 Video Light x1 Reflector (Bowens Mount) x1 (not included in CL330M Lite) Carrying Bag x1 (not included in CL330 Lite) 3m Plum Tail Cable x1 Power Adapter (with Wire Lanyard) x1 Warranty Card x1 NB3.58Optional x1 COB Cover x1 Power adapters may vary according to sales region. Form 1 Illumination CCT 1m 3m 5m Light Base LUX 2700K Reflector FC LUX FC Light Base LUX 3200K Reflector FC LUX FC Light Base LUX 4300K Reflector FC LUX FC Light Base LUX 5600K FC Reflector LUX FC Light Base LUX 6500K Reflector FC LUX FC 10800 1000 56900 5280 11300 1050 59700 5540 11900 1110 63400 5890 12400 1150 65800 6110 12600 1170 66700 6200 1700 158 5400 502 1780 165 5640 524 1900 132 5950 552 1970 183 6160 572 2030 188 6190 575 740 69 2270 211 778 72 2370 220 824 77 2510 233 853 79 2600 241 886 82 2620 244 The data is given from testing in a laboratory baesed on BHR45. WARRANTY Warranty Period Thank you for purchasing COLBOR products. 1.Customers are entitled to free replacement or repair service in case of quality defect(s) found in the product under normal use within 30 days upon receipt of the product. 2.Original COLBOR products are entitled to 12-month limited warranty service. The warranty period begins on the date of purchase of brand new, unused products by the first end-user. Within the warranty period, if product defect or failure is attributable to material defection or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee). Warranty Exclusions and Limitations 1.Faults resulted from inappropriate use of a product without following its operation specification 2.Artificial damage, e.g. crash, squeeze, scratch, soaking, exposing to rain or damp 3.Modifications to a product by its user or a third party without prior written consent of COLBOR, e.g. replacement of element or circuit, label alteration 4.The code on product is inconsistent with that of warranty certificate, or the code on the product or warranty certificate is altered or torn off 5.All consumable accessory attached to a product, like cable, cover 6.Faults as a result of force majeure, such as fire, flood, lightning, etc. Warranty Claim Procedure 1.If failure or any problem occurs to your product after purchase, please contact a local agent for assistance, or you can always contact COLBOR's customer service through email. 2.Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents is missing, only sales return or chargeable service will be provided. 3.If the COLBOR product is out of the warranty coverage, the service and the parts cost will be charged. Guangzhou Zhiying Technology Co., Ltd Room 2401, 24 / F, South Tower, Lisheng Plaza, No. 68 Huadi Avenue, Liwan District, Guangzhou, China, 510000 support@colborlight.com www.colborlight.com