Instruction Manual for PRECISION LIGHTING models including: Domino 1 Recessed Trimless, Recessed Trimless, Trimless
File Info : application/pdf, 8 Pages, 1.65MB
DocumentDocumentinstruction manual Domino Recessed The Domino Recessed family are recessed 95CRI architectural luminaires that offer a wide range of optical distributions. Domino Recessed 1 - 2.2W, 178lm Domino Recessed 2 - 4.4W, 356lm Domino Recessed 4 - 8.8W, 712lm These instructions are applicable for Domino Recessed 1, 2 and 4 variations. Domino Recessed Springs parallel TX-654 Recess Domino 4 Spring maximum extension 165mm 6 1/2" 2mm 1/16" 119mm 4 11/16" 42mm 1 5/8" Springs perpendicular 53mm 2 1/16" Cutout 66 ø44 TX-652 Recess Domino 2 Spring maximum extension 120mm 4 3/4" 2mm 1/16" 75mm 2 15/16" 42mm 1 5/8" Component List Minimum ceiling void: 20mm / 3/4" above luminaire TX-651 Recess Domino 1 Spring maximum extension 90mm 3 1/2" 2mm 1/16" ø53mm 2 1/6" 42mm 1 5/8" Luminaire Module Optics Optic Holder Accessory holder 53mm 2 1/16" ø53mm 2 1/6" Relco 30W 700mA 1-10V Dim PSCC-30-700-A-RE QTY QTY QTY Domino 1 Domino 2 Domino 4 1-12 1-6 1-3 22 ø44 REMOTE DRIVER ONLY ø44 Harvard 700mA 14W DALI dim PSCC-14-700-D-HA QTY QTY QTY Domino 1 Domino 2 Domino 4 3-6 2-3 1 These luminaires are constant current and must be connected to an appropriate driver as recommended by Precision Lighting. 1. All systems must be installed by a suitably qualified professional only. Installations must conform to national installation and accident prevention regulations. 2. Do not install any fixture closer than 150mm (6 inches) from any combustible material. Do not install these products in a damp or wet location. 3. To reduce the risk of fire and burns, do not install these products where exposed bare conductors can be shorted or contact any conductive materials. Do not conceal or extend exposed conductors through a building wall. 4. Ensure all connections are tight. Bad connections can cause overheating, arcing and a potential fire risk. 5. This luminaire must be wired and grounded in accordance with standard accepted electrical installation practices, local codes and ordinances. 6. Wire supply connections must be made with UL or compatible testing agency approved connectors. 7. Ensure the luminaire's Jack Plug is correctly inserted into the selected power system.The Jack Plug should not be cross threaded and should be fully tightened. 8. Always use appropriate optics and ensure they are fitted securely. 9. Use only as described in this Precision Lighting manual. 10. Use only Precision Lighting recommended accessories. 11. Ensure that the luminaire is switched off at mains supply before installing or removing. 12. Luminaires may be extremely hot, allow to cool before touching. 13. These are 700mA constant current luminaires and must be connected to an appropriate PSU as recommended by Precision Lighting. 14. Regular cleaning of these products is important. Switch off at mains supply and allow to cool before cleaning fittings with a microfibre cloth.Then reconnect the power supply. WARNING Do not connect or disconnect under load. Ensure driver has not been powered for a minimum of 1 minute before reconnecting the LED module after disconnecting. Do not hot plug. Failure to follow this instruction will lead to serious damage of the LED module and driver and will not be covered by warranty. NOTE Maintain correct polarity when wiring. Incorrect wiring will cause serious damage and will not be covered by warranty. Must be installed according to SELV regulations. Wire specif ication: 22 AWG, ø0.65mm diameter double insulated tef lon wire. Red - Positive Black - Negative NOTE LED module is not site serviceable. Tampering will cause damage and will not be covered by warranty. Domino 4 Recessed Domino 1 Recessed Domino 2 Recessed 1. Installing the luminaire WARNING switch off power to mains before installation. Cut ceiling hole using the stencils in diagram 1.1. Note: Due to small luminaire size drivers must be located remotely when using the Domino 1; cut out is too small for dimmable drivers to pass through. Pull driver side connector through hole and connect to the luminaire side connector. See electrical instructions for wiring schematic. Compatible drivers listed in front page table. Using installation springs, install fixture into the ceiling. 1.1 66 mm 2 19/32" ø44 ø44 22 7/8" REMOTE DRIVER ONLY ø44 1 3/4" Please note the Domino Recessed 1 requires remote driver location due to small cutout size. PRINT TO SCALE 1.2 Driver WARNING Do not connect or disconnect under load. Ensure driver has not been powered for a minimum of 1 minute before reconnecting the LED module after disconnecting. Do not hot plug. Failure to follow this instruction will lead to serious damage of the LED module and driver and will not be covered by warranty. NOTE Maintain correct polarity when wiring. Incorrect wiring will cause serious damage and will not be covered by warranty. Must be installed according to SELV regulations. Wire specif ication: 22 AWG, ø0.65mm diameter double insulated tef lon wire. Red - Positive Black - Negative NOTE LED module is not site serviceable. Tampering will cause damage and will not be covered by warranty. 2. Changing the optics WARNING luminaire may be hot. Allow to cool before touching. Remove the luminaire from the ceiling. Using the slot on the side of the Magnetic Front Plate remove the plate. We recommend using a screwdriver for leverage. Remove the optics and replace with the new selection.To position the new optics correctly place the optics into the cover and replace. Screw the optic holder back in to place using the 2 cross head screws. Reinstall onto ceiling as per step 1. 3. Using Accessories WARNING luminaire may be hot. Allow to cool before touching. Using the slot on the side of the Magnetic Front Plate remove the plate. We recommend using a screwdriver for leverage. Insert accessory into Magnetic Front Plate and replace Front Plate into the main body. WARNING Do not connect or disconnect under load. Ensure driver has not been powered for a minimum of 1 minute before reconnecting the LED module after disconnecting. Do not hot plug. Failure to follow this instruction will lead to serious damage of the LED module and driver and will not be covered by warranty. NOTE Maintain correct polarity when wiring. Incorrect wiring will cause serious damage and will not be covered by warranty. Must be installed according to SELV regulations. Wire specif ication: 22 AWG, ø0.65mm diameter double insulated tef lon wire. Red - Positive Black - Negative NOTE LED module is not site serviceable. Tampering will cause damage and will not be covered by warranty. 4. Remove fixture from ceiling Hold the bezel and pull downwards. Tilt fixture in direction of one of the installation springs and continue to pull down before straightening out the fixture and pulling down until the fixture is clear of the ceiling. WARNING caution springs can pinch fingers. Handle with care. Disconnect from driver. WARNING Ensure mains supply is off before disconnecting luminaire. Driver instruction manual Domino Recessed Trimless The Domino Recessed Trimless family are 95CRI architectural luminaires that offer a wide range of optical distributions. Domino 1 Recessed Trimless - 2.2W, 178lm Domino 2 Recessed Trimless - 4.4W, 356lm Domino 4 Recessed Trimless - 8.8W, 712lm These instructions are applicable for Domino Recessed Trimless 1, 2 and 4 variations. Domino Recessed Trimless Springs parallel TX-654 Recess Domino 4 Spring maximum extension 165mm 6 1/2" 106 4 3/16" 134 5 1/4" Springs perpendicular 42mm 1 5/8" ø68mm 2 11/16" Cutout 66 ø44 TX-652 Recess Domino 2 Spring maximum extension 120mm 4 3/4" 62 2 7/16" 90 3 9/16" 42mm 1 5/8" ø68mm 2 11/16" 22 ø44 Component List Minimum ceiling void: 20mm / 3/4" above luminaire TX-651 Recess Domino 1 Spring maximum extension 90mm 3 1/2" Plaster Ring ø40 1 9/16" ø68 2 11/16" 42mm 1 5/8" Luminaire Module Optics Optic Holder ø68mm 2 11/16" REMOTE DRIVER ONLY ø44 Accessory holder Relco 30W 700mA 1-10V Dim PSCC-20-700-A-RE QTY QTY QTY Domino 1 Domino 2 Domino 4 1-12 1-6 1-3 Harvard 700mA 14W DALI dim PSCC-14-700-D-HA QTY QTY QTY Domino 1 Domino 2 Domino 4 3-6 2-3 1 These luminaires are constant current and must be connected to an appropriate driver as recommended by Precision Lighting. 1. All systems must be installed by a suitably qualified professional only. Installations must conform to national installation and accident prevention regulations. 2. Do not install any fixture closer than 150mm (6 inches) from any combustible material. Do not install these products in a damp or wet location. 3. To reduce the risk of fire and burns, do not install these products where exposed bare conductors can be shorted or contact any conductive materials. Do not conceal or extend exposed conductors through a building wall. 4. Ensure all connections are tight. Bad connections can cause overheating, arcing and a potential fire risk. 5. This luminaire must be wired and grounded in accordance with standard accepted electrical installation practices, local codes and ordinances. 6. Wire supply connections must be made with UL or compatible testing agency approved connectors. 7. Ensure the luminaire's Jack Plug is correctly inserted into the selected power system.The Jack Plug should not be cross threaded and should be fully tightened. 8. Always use appropriate optics and ensure they are fitted securely. 9. Use only as described in this Precision Lighting manual. 10. Use only Precision Lighting recommended accessories. 11. Ensure that the luminaire is switched off at mains supply before installing or removing. 12. Luminaires may be extremely hot, allow to cool before touching. 13. These are 700mA constant current luminaires and must be connected to an appropriate PSU as recommended by Precision Lighting. 14. Regular cleaning of these products is important. Switch off at mains supply and allow to cool before cleaning fittings with a microfibre cloth.Then reconnect the power supply. WARNING Do not connect or disconnect under load. Ensure driver has not been powered for a minimum of 1 minute before reconnecting the LED module after disconnecting. Do not hot plug. Failure to follow this instruction will lead to serious damage of the LED module and driver and will not be covered by warranty. NOTE Maintain correct polarity when wiring. Incorrect wiring will cause serious damage and will not be covered by warranty. Must be installed according to SELV regulations. Wire specif ication: 22 AWG, ø0.65mm diameter double insulated tef lon wire. Red - Positive Black - Negative NOTE LED module is not site serviceable. Tampering will cause damage and will not be covered by warranty. Domino 4 Trimless Domino 1 Trimless Domino 2 Trimless 1. Installing the luminaire. WARNING switch off power to mains before installation. Cut ceiling hole using the stencils in diagram 1.1. Note: Due to small luminaire size drivers must be located remotely when using the Domino 1; cut out is too small for dimmable drivers to pass through. Position plaster-in ring and use appropriate fixings to secure to ceiling. Pull driver side connector through hole. Apply plaster over plaster-in ring and skim. Avoid covering wires with plaster. Cut around the inside of the aperture to ensure a neat finish. 1.1 66 mm 2 19/32" ø44 ø44 22 7/8" REMOTE DRIVER ONLY ø44 1 3/4" Please note the Domino Recessed 1 requires remote driver location due to small cutout size. PRINT TO SCALE WARNING Do not connect or disconnect under load. Ensure driver has not been powered for a minimum of 1 minute before reconnecting the LED module after disconnecting. Do not hot plug. Failure to follow this instruction will lead to serious damage of the LED module and driver and will not be covered by warranty. NOTE Maintain correct polarity when wiring. Incorrect wiring will cause serious damage and will not be covered by warranty. Must be installed according to SELV regulations. Wire specif ication: 22 AWG, ø0.65mm diameter double insulated tef lon wire. Red - Positive Black - Negative NOTE LED module is not site serviceable. Tampering will cause damage and will not be covered by warranty. Once plaster is dry, ensure control gear is not connected to mains supply before attaching the luminaire side connector to the driver side connector. Using installation springs, install fixture into the ceiling. Insert accessory into Magnetic Front Plate and replace Front Plate into the main body. 2. Removing the luminaire module from the ceiling. Remove the magnetic accessory holder. Hook fingers into holes on either side of the luminaire housing. A tool can be used for leverage if necessary.Tilt fixture in direction of one of the installation springs and continue to pull down before straightening out the fixture and pulling down until the fixture is clear of the ceiling. WARNING caution springs can pinch fingers. Handle with care. Disconnect from driver. WARNING Ensure mains supply is off before disconnecting luminaire. Driver Driver WARNING Do not connect or disconnect under load. Ensure driver has not been powered for a minimum of 1 minute before reconnecting the LED module after disconnecting. Do not hot plug. Failure to follow this instruction will lead to serious damage of the LED module and driver and will not be covered by warranty. NOTE Maintain correct polarity when wiring. Incorrect wiring will cause serious damage and will not be covered by warranty. Must be installed according to SELV regulations. Wire specif ication: 22 AWG, ø0.65mm diameter double insulated tef lon wire. Red - Positive Black - Negative NOTE LED module is not site serviceable. Tampering will cause damage and will not be covered by warranty. 3. Changing the optics. WARNING luminaire may be hot. Allow to cool before touching. Remove the luminaire from the ceiling. Using the slot on the side of the Magnetic Front Plate remove the plate. We recommend using a screwdriver for leverage. Remove the optics and replace with the new selection.To position the new optics correctly place the optics into the cover and replace. Screw the optic holder back in to place using the 2 cross head screws. Reinstall onto ceiling as per step 1. 4. Using accessories. WARNING luminaire may be hot. Allow to cool before touching. Using the slot on the side of the Magnetic Front Plate remove the plate. We recommend using a screwdriver for leverage. Insert accessory into Magnetic Front Plate and replace Front Plate into the main body.Adobe InDesign CS6 (Macintosh) Adobe PDF Library 10.0.1