Bed Assembly Instructions

Safety And Care Advice

Important - Please read these instructions fully before starting assembly.

Please check if all the components and tools listed out are received.
Please remove all fittings from the plastic bags and separate them into homologous groups.
Please keep children and animals away from the working areas; swallow small parts may cause suffocation. ??
Please make sure you have enough space to lay out the parts before starting.
Do not stand on the product, which could cause damage.
Please assemble the product as close to its final position as possible.
Do not place furniture directly in front of radiators, fires, or any other source of heat.
The assembly will be easier with 2 people. ?‍?‍?
Please dispose of all packaging carefully and responsibly. ?️

General care and maintenance

Please clean with a damp cloth or mild detergent, do not use bleach or abrasive cleaners.
Do not allow the spill to stay on the surface for a long time.
Do not clean with products containing the following: acetone (e.g., nail varnish remover), ammonia (e.g., bleach), or sodium hydroxide (e.g., caustic soda, drain, and oven cleaners).
If the product is accidentally exposed to the irritating liquid, rinse thoroughly with clean water.
Mats can be used to protect surfaces from moisture and heat.
Please check whether there are missing screws in the product regularly.
The product should not be discarded with household waste, and please take it to your local authority waste disposal center. ♻️

Installation Tools

Tools Required:

Phillips screwdriver ➕
Allen key (5*5 mm)
Allen key (3*3 mm)

Diagram Description: Shows a plus sign icon for a screwdriver and two L-shaped Allen keys of different sizes, accompanied by circular washers.

Hardware List

A: M8*12 mm (10x)
B: M8*16 mm (23x)
C: M8*38 mm (16x)
D: M8*55 mm (3x)
E: M5*30 mm (8x)
F: ST4.2*12 mm (2x)
G: 5*5 mm Allen Key (1x)
H: 3*3 mm Allen Key (1x)
K: Light strip connection line & controller (1x)
U: Socket with USB (1x)

Parts List

Tips for labels:

K: Light strip connection line & controller
U: Socket with USB

Diagram Description: An isometric view of the bed frame showing numbered parts. Key components include: 1: Side rail (2x), 2: Headboard panel (1x), 3: Headboard support (2x), 4: Support bracket (4x), 5: Slat (approx. 18-20x), 6: Center support rail (2x), 7: Cross support (multiple), 8: Footboard support (1x), 9: Leg (4x), 10: Base panel (1x), 11: Headboard frame (1x), 12: Headboard decorative panel (1x), 13: Headboard mounting bracket (2x), 14: Footboard frame (1x), 15: LED strip channel (1x), 16: LED strip mounting bracket (2x), 17: USB socket mounting bracket (2x), 18: Footboard rail (1x).

Assembly Instructions

Step 1

Attach two headboard mounting brackets (part 13) to the base panel (part 10) using eight M8*12 mm screws (hardware A). Diagram shows the base panel and brackets being joined with checkmark and cross indicators for correct/incorrect placement.

Step 2

Attach the footboard frame (part 14) to the base panel (part 10) using four M8*16 mm screws (hardware B).

Step 3

Attach the two headboard supports (part 3) to the base panel (part 10) using four M8*16 mm screws (hardware B).

Step 4

Assemble the headboard frame (part 11) by attaching it to the headboard supports (part 3) and the base panel (part 10) using eight M8*38 mm screws (hardware C). Note: "Please keep the screws half-tightened during installation." ? ?️

Step 5

Attach two USB socket mounting brackets (part 17) to the headboard frame (part 11) using two M8*12 mm screws (hardware A).

Step 6

Attach the two center support rails (part 6) to the base panel (part 10) using eight M5*30 mm screws (hardware E) and three M8*16 mm screws (hardware B). Note: "Tighten all the screws at this step." ?

Step 7

Unfold or open the two side rails (part 1). Warning: "Be careful not to pinch yourself when opening the brackets." ⚠️ ➡️ ↪️ ❌ Multilingual warning: CAUTION, PINCH POINT, RISQUE DE PINCEMENT, PUNTO DE PELLIZCO.

Step 8

Attach the two side rails (part 1) to the assembled headboard and footboard frames using four M8*16 mm screws (hardware B). Diagram shows the side rails connecting to the main structure with arrows indicating attachment points.

Step 9

Attach the headboard decorative panel (part 12) to the headboard frame (part 11) using four M8*16 mm screws (hardware B). Diagram shows the decorative panel being attached to the headboard with arrows indicating attachment points.

Step 10

Attach the cross supports (part 7) to the side rails (part 1) using four M8*38 mm screws (hardware C). Diagram shows cross supports being added to the bed frame with arrows.

Step 11

Attach the center support rails (part 6) to the headboard and footboard frames using four M8*38 mm screws (hardware C) and four M8*16 mm screws (hardware B). Diagram shows the center supports being secured with arrows.

Step 12

Attach the four legs (part 9) to the underside of the side rails (part 1) using four M8*16 mm screws (hardware B). Diagram shows legs being attached to the bed frame with arrows.

Step 13

Attach the four support brackets (part 4) to the side rails (part 1) using three M8*55 mm screws (hardware D). Diagram shows brackets being attached to the inner side of the rails with arrows.

Step 14

Insert the slats (part 5) into the support brackets (part 4) and center support rails (part 6). Instruction: "Please mind to push hard." Diagram shows slats being pushed into place with arrows.

Step 15

Install the USB socket with USB (part U) into the designated bracket and secure it using two ST4.2*12 mm screws (hardware F). Diagram shows the socket being fitted and screwed in.

Step 16

Attach the light strip connection line & controller (part K). Instruction: "Tear double-sided adhesive tape apart". Diagram shows the controller being attached using adhesive tape.

Instructional Literature for Consumer Products Containing Button Cell or Coin Batteries

Important Safety Items:

Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate. ??️
Even used batteries may cause severe injury or death.
Call a local poison control center for treatment information.
The compatible battery type is CR2025.
The nominal battery voltage is 3 volt.
Non-rechargeable batteries are not to be recharged.
Do not force discharge, recharge, disassemble, heat above (40°C) or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns. ⚠️?

Additional Items for Products with Replaceable Button Cell or Coin Batteries:

Ensure the batteries are installed correctly according to polarity (+ and -). ➕➖
Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

WARNING

INGESTION HAZARD: This product contains a button cell or coin battery.

DEATH or serious injury can occur if ingested.

A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.

KEEP new and used batteries OUT OF REACH of CHILDREN. ??

Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body. ⚕️

LED Controller Key Description

Key Description:

I. MODE key: Control to change the flashing mode of the LED light.
II. SPEED key:
- 1. Switch
  - a. Press the button to turn on the LED light. ▶️
  - b. Press and hold the button for 3s to turn off the LED light. ⏹️
- 2. Press to adjust the speed when the LED light is flashing.
- 3. Press to adjust the brightness when the LED light is constantly on.
III. COLOR key: Control to change the color of the LED light.

Diagram Description: A vertical controller with labels "RGB LED", "MODE DEMO", "SPEED", "COLOR", and power indicators "5V" and a ground symbol ⏚.

	Wrought Studio Queen Size Bed Frame Assembly Instructions (DKPE2847) Comprehensive assembly instructions for the Wrought Studio Queen Size Lift-Up Storage Bed Frame with Bookcase Headboard and LED Lights (Model DKPE2847). Includes detailed parts list, hardware guide, and step-by-step assembly process.
	Wrought Studio Metal Bed Frame Assembly Instructions \| Model ON-MT01 Detailed assembly instructions for the Wrought Studio metal bed frame (Model ON-MT01). Includes parts list, hardware guide, and step-by-step assembly process for easy setup.
	Wrought Studio Farmhouse Queen Size Storage Bed Frame Assembly Instructions Detailed assembly instructions for the Wrought Studio Farmhouse Queen Size Storage Bed Frame with Bookcase Headboard and 4 Drawers (Models DJ504740, DJ504741). Includes part list, hardware list, and step-by-step guidance for assembly.
	Wrought Studio Princess Bed Frame Assembly Instructions with LED Lights Comprehensive assembly instructions for the Wrought Studio Princess Bed Frame, featuring LED lights and a charging station. Includes parts list, hardware guide, and step-by-step assembly.
	Wrought Studio Bed Frame Installation Guide and Product Manual Detailed installation guide and product manual for the Wrought Studio Bed Frame, including parts list and step-by-step assembly instructions for model brhh1050.
	Assembly Instructions for Wrought Studio Bed Frame with Charging Station and Storage Drawers Detailed assembly instructions for the Wrought Studio metal frame platform bed, featuring a storage headboard with charging station and four drawers. Includes parts list, hardware list, and step-by-step guidance.
	Wrought Studio Farmhouse Bed Frame Assembly Instructions - Model QHB-003Q Comprehensive assembly guide for the Wrought Studio Farmhouse Bed Frame, featuring double barn door storage headboard, LED lights, and rustic wooden design. Includes parts list, hardware details, and step-by-step instructions for model QHB-003Q.
	Wrought Studio ehcm1254 Upholstered Bed Frame Assembly Instructions Detailed assembly instructions for the Wrought Studio ehcm1254 upholstered bed frame with storage drawers. Includes parts list, step-by-step guidance, and important warnings for safe assembly.