User Manual for Prestel models including: ETP-XUSB3 USB 3.0 Extender, ETP-XUSB3, USB 3.0 Extender, 3.0 Extender, Extender
Комплект передачи USB 3.2 по витой паре, до 100м, Prestel ETP-XUSB3
Prestel ETP-XUSB3 USB 3.0 Extender (100M) USER MANUAL Tha nk yo u fo r purc ha sing this pro duc t For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. Surg e pro te c tio n de vic e re c o m m e nde d This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lighting strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment. C a utio n The product requires the use of UTP connectors. Please connect in direct interconnection method and do not cross connect. White and Orange Orange White and Green Blue White and Blue Green White and Brown Brown Direct Interconnection Method Ta b le o f C o nte nts 1. Intro duc tio n........................................................................................... 1 2. Fe a ture s................................................................................................. 1 3. Pa c ka g e C o nte nts................................................................................ 1 4. Spe c ific a tio ns....................................................................................... 2 5. O pe ra tio n C o ntro ls a nd Func tio ns...................................................... 3 5.1 Tra nsm itte r Pa ne l............................................................................. 3 5.2 Re c e ive r Pa ne l................................................................................ 4 6. Applic a tio n Exa m ple ............................................................................ 5 1. Intro duc tio n The USB 3.0 Extender can extend USB signal to a distance up to 100m/328ft via a single CAT6a cable. Transmitter features with one USB 3.0 Type B input, one FSYSNC GPIO input and one RS-232 pass-through. Receiver features with four USB 3.0 Type A outputs, one FSYSNC GPIO output and one RS-232 pass-through. Bi-directional 24V PoC is also supported. The product can be widely used for long distance signal transmission between a PC and USB devices. 2. Fe a ture s Extension of USB 3.0 up to 100m/328ft over CAT6a cable USB 3.0 connectivity with data transfer rate up to 5Gbps Backwards compatible with USB 2.0 and 1.1 Hardware acceleration for isochronous and bulk transfer USB-A port 1 and 2 support 5V/1.5A, port 3 and 4 support 5V/1A on the Receiver Support RS-232 pass-through and FSYNC GPIO pass-through (for industry camera use) Support bi-directional 24V PoC Simple plug and play, no driver and setting installation required 3. Pa c ka g e C o nte nts 1× USB 3.0 Extender (Transmitter) 1× USB 3.0 Extender (Receiver) 1× 24V/2A Locking Power Supply 2× 4pin-3.5mm Phoenix Connector (Male) 4× Mounting Ear 8× Machine Screw (KM3*4) 1× User Manual 1/5 4. Spe c ific a tio ns Technical USB Protocol USB 3.0 Transmission Rate Up to 5Gbps Network Bandwidth 10G Transmission Distance 100m/328ft over CAT6a (F/FTP) cable ESD Protection IEC 61000-4-2: ±8kV (Air-gap discharge), ±4kV (Contact discharge) Connections Transmitter Input: 1 × USB HOST [USB-B, 9pin Female] Output: 1 × HDBT OUT [RJ45, Female] Control: 1 × RS-232 [3pin-3.5mm Phoenix Connector] 1 × FSYNC [1pin-3.5mm Phoenix Connector] 1 × SERVICE [USB-C, Update Port] Receiver Input: 1 × HDBT IN [RJ45, Female] Output: 4 × USB Devices [USB-A, 9pin Female] Control: 1 × RS-232 [3pin-3.5mm Phoenix Connector] 1 × FSYNC [1pin-3.5mm Phoenix Connector] 1 × SERVICE [USB-C, Update Port] Mechanical Housing Metal Enclosure Color Black Dimensions Transmitter / Receiver: 85mm [W] × 100mm [D] × 25.5mm [H] Weight Power Supply Transmitter: 253g, Receiver: 260g Input: AC 100~240V 50/60Hz Output: DC 24V/2A Power Consumption PoC Power Supply: 40W (Max) Operating Temperature 0°C ~ 40°C / 32°F ~ 104°F Storage Temperature -20°C ~ 60°C / -4°F ~ 140°F Relative Humidity 20~90% RH (non-condensing) 2/5 5. O pe ra tio n C o ntro ls a nd Func tio ns 5.1 Tra nsm itte r Pa ne l USB HOST TX USB 12 HDBT OUT LINK TX RX IO SERVICE RS-232 FSYNC DC 24V 3 4 5 6 78 9 No. Name Function Description 1 USB HOST Host port, supporting USB 3.0. Connects to a PC or host. 2 USB LED USB signal indicator. On: USB signal is detected. Off: USB signal is not detected. 3 HDBT OUT Connects to the HDBT IN port on Receiver with CAT cable. 4 LINK LED Connection signal indicator. On: Transmitter and Receiver are connected and linked. Flashing: Transmitter and Receiver link is off due to USB low power mode. Off: Transmitter and Receiver are not connected. 5 RS-232 3pin phoenix connector, connected to a PC or control system for RS-232 command pass-through. 6 FSYNC FSYNC port, used for level pass-through to the Receiver, and synchronizing the external devices. The default level is 3.3V. 7 SERVICE Firmware update port. 8 POWER LED The LED will be on when the Transmitter is powered on. 9 DC 24V DC 24V/2A power input port. 3/5 5.2 Re c e ive r Pa ne l 1 2 1.5A 1 3 4 RX USB 1A 23 HDBT IN LINK TX RX IO SERVICE RS-232 FSYNC DC 24V 4 5 6 7 8 9 10 No. Name Function Description 1 USB 12 Connect to USB devices, and max output power is up to 5V/1.5A. 2 USB 3/4 Connect to USB devices, and max output power is up to 5V/1A. 3 USB LED USB signal indicator. On: USB signal is detected. Off: USB signal is not detected. 4 HDBT IN 5 LINK LED Connects to the HDBT OUT port on Transmitter with CAT cable. Connection signal indicator. On: Transmitter and Receiver are connected and linked. Flashing: Transmitter and Receiver link is off due to USB low power mode. Off: Transmitter and Receiver are not connected. 6 RS-232 3pin phoenix connector, connected to a PC or control system for RS-232 command pass-through. 7 FSYNC FSYNC port, receiving level pass-through from the Transmitter, and synchronizing the external devices. Default level is 3.3V. 8 SERVICE Firmware update port. 9 POWER LED The LED will be on when the Receiver is powered on. 10 DC 24V DC 24V/2A power input port. 4/5 6. Applic a tio n Exa m ple USB HOST USB TX HDBT OUT Transmitter LINK TX RX IO SERVICE RS-232 FSYNC DC 24V CAT6a PC 1 2 1.5A USB Camera 3 4 RX USB 1A HDBT IN Receiver U Disk LINK TX RX IO SERVICE RS-232 FSYNC DC 24V Power Supply 5/5Adobe PDF library 15.00