Greenworks 2101602CT String Trimmer Operator Manual

1 Description

1.1 Purpose

This machine is used to cut grass, light weeds, and other similar vegetation at or around ground level. The cutting plane must be approximately parallel to the ground surface. You cannot use the machine to cut or chop hedges, shrubs, bushes, flowers and compost.

1.2 Overview

The overview diagram shows the following parts:

• 1: Rear handle
• 2: Auxiliary handle
• 3: Coupler
• 4: Trimmer shaft
• 5: Edge guide
• 6: Guard
• 7: Battery release button
• 8: Lock-out button
• 9: Trigger

2 Important Safety Instructions

⚠️ [Warning] Read and understand all instructions before using this product. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.

• Use only identical manufacturer's replacement parts and accessories. Use of any other parts may create a hazard or cause product damage.
• Always wear safety glasses with side shields marked to comply with ANSI Z87.1. Everyday glasses have only impact resistant lenses. They are NOT safety glasses. Following this rule will reduce the risk of eye injury. Use face mask if operating in dusty work spaces.
• Avoid Dangerous Environment: Do not expose power tools to damp or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Do not use in rain.
• Keep all bystanders, children, and pets at least 50 ft. away.
• Dress Properly: Do not wear loose clothing or jewelry. They can be caught in moving parts. Use of rubber gloves and substantial footwear is recommended when working outdoors. Wear protective hair covering to contain long hair.
• Use the right Appliance: Do not use appliance for any job except that for which it is intended.
• Avoid Unintentional Starting: Do not carry appliance with finger on switch. Be sure switch is off when battery is plugged in.
• Do not Force Appliance: It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.
• Do not overreach: Keep proper footing and balance at all times.
• Stay alert: Watch what you are doing. Use common sense. Do not operate this unit when you are tired, ill or under the influence of alcohol, drugs or medication.
• Always store idle power tools indoors: When not in use, power tools should be stored indoors in a dry and high or locked-up place, out of reach of children.
• Maintain Appliance With Care: Replace string head if cracked, chipped, or damaged in any way. Be sure the string head is properly installed and securely fastened. Keep cutting edge sharp and clean for best performance and to reduce the risk of injury. Follow instructions for lubricating and changing accessories. Inspect appliance cord periodically, and if damaged, have it repaired by an authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease. Failure to do so can cause serious injury.
• Check damaged parts before using the appliance: A guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, damaged mountings, and any other condition that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless indicated elsewhere in this manual.
• Remove or disconnect battery before servicing, cleaning or removing material from the gardening appliance.
• Do not modify or attempt to repair the appliance or the battery pack (as applicable) except as indicated in the instructions for use and care. Use appliances only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. Use only Greenworks 29662/29652 battery or other BAF series.
• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. Use only Greenworks 29692 charger or other CAF series.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
• Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 265 °F (130 °C) may cause an explosion.
• Do not dispose of the batteries in a fire. The cells may explode. Check with local codes for possible special disposal instructions.
• Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.
• Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.
• Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
• Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
• Keep guards in place and in working order.
• Keep hands and feet away from cutting area.
• Disconnect the battery pack from the appliance before making any adjustments, changing accessories, or storing appliance. Such preventive safety measures reduce the risk of starting the appliance accidentally.
• Use only with the nylon cutting line of 0.065" (1.65 mm) diameter. Do not use heavier lines than recommended by the manufacturer and line materials of other types – for example, metal wire, rope, and the like.

SAVE THESE INSTRUCTIONS

3 Symbols on the Machine

Some of the following symbols can be used on this machine. Please study them and learn their definition. Proper interpretation of these symbols will let you operate the tool better and safer.

4 Risk Levels

The following signal words and meanings are intended to explain the levels of risk associated with this product.

5 Service

Servicing requires extreme care and knowledge and must be performed only by a qualified service technician. For service we suggest you return the machine to your nearest AUTHORIZED SERVICE CENTER for repair. Use only identical manufacturer's replacement parts and accessories.

6 Environmentally Safe Battery Disposal

The toxic and corrosive materials below are in the batteries used in this machine: Lithium-Ion, a toxic material.

⚠️ [Warning] Discard all toxic materials in a specified manner to prevent contamination of the environment. Before discarding damaged or worn out Li-ion battery, contact your local waste disposal agency, or the local Environmental Protection Agency for information and specific instructions. Take the batteries to a local recycling and/or disposal center, certified for lithium-ion disposal.

⚠️ [Warning] If the battery pack cracks or breaks, with or without leaks, do not recharge it and do not use. Discard it and replace with a new battery pack. DO NOT TRY TO REPAIR IT! To prevent injury and risk of fire, explosion, or electric shock, and to avoid damage to the environment:

• Cover the terminals of the battery with heavy-duty adhesive tape.
• DO NOT try to remove or destroy any of the battery pack components.
• DO NOT try to open the battery pack.
• If a leak develops, the released electrolytes are corrosive and toxic. DO NOT get the solution in the eyes or on skin, and do not swallow it.
• DO NOT put these batteries in your regular household trash.
• DO NOT incinerate.
• DO NOT put them where they will become part of any waste landfill or municipal solid waste stream.
• Take them to a certified recycling or disposal center.

♻️ [Recycle Symbol] RBRC Li-ion TM 1.800.822.8837

7 Proposition 65

⚠️ [Warning] This product contains a chemical known to the state of California to cause cancer, birth defects or other reproductive harm. Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints;
• Crystalline silica from bricks and cement and other masonry products;
• Arsenic and chromium from chemically treated lumber.

Your risk of exposure to these chemicals varies depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

8 Installation

8.1 Unpack the Machine

⚠️ [Warning] Make sure that you correctly assemble the machine before use.

⚠️ [Warning] If the parts are damaged, do not use the machine. If you do not have all the parts, do not operate the machine. If the parts are damaged or missing, speak to the service center.

1. Open the package.
2. Read the documentation in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and package in compliance with local regulations.

8.2 Attach the Guard

⚠️ [Warning] Do not touch the cut-off blade.

1. Remove the screws (1) from the trimmer head with a Phillips head screwdriver (not included).
2. Put the guard (2) onto the trimmer head.
3. Align the screw holes on the guard (3) with the screw holes on the trimmer head (4).
4. Tighten the screws.

8.3 Assemble the Shaft

1. Loosen the knob (1) on the coupler.
2. Push in the release button (2) on the lower shaft (3).
3. Align the release button (2) with the positioning hole (4) and slide the two shafts.
4. Turn the lower shaft until the button locks into the positioning hole.
5. Tighten the knob.

8.4 Attach the Auxiliary Handle

1. Press the auxiliary handle (1) onto the upper shaft.
2. Slide the auxiliary handle over the metal ring (2) and ensure the metal ring fits between the slot on the auxiliary handle.
3. Align the holes on the auxiliary handle with the holes on metal ring.
4. Tighten the auxiliary handle with the knob (3).

8.5 Install the Battery Pack

⚠️ [Warning] If the battery pack or charger is damaged, replace the battery pack or the charger.

⚠️ [Warning] Stop the machine and wait until the motor stops before you install or remove the battery pack.

⚠️ [Warning] Read and understand the instructions in the battery and charger manual.

1. Align the lift ribs (3) on the battery pack with the grooves in the battery compartment.
2. Push the battery pack into the battery compartment until the battery pack locks into place.
3. When you hear a click, the battery pack is installed.

8.6 Remove the Battery Pack

1. Push and hold the battery release button (1).
2. Remove the battery pack from the machine.

9 Operation

❗ [Important] Before you operate the machine, read and understand the safety regulations and the operation instructions.

⚠️ [Warning] Be careful when you operate the machine.

9.1 Controls

The controls include the lock-out button and the trigger.

9.2 Start the Machine

1. Push the lock-out button (1) and pull the trigger (2). Once the machine is running you can release the lock-out button.

9.3 Stop the Machine

1. Release the trigger to stop the machine.

9.4 Adjust the Length of the Cutting Line

ℹ️ [Note] The machine has an auto-feed head. It will damage the machine if you hit the head to try to advance the line.

ℹ️ [Note] If the cutting line does not automatically advance, it can be tangled or empty.

1. When the machine is on, release the trigger.
2. Wait two seconds, push the trigger again.
3. Resume trimming.

ℹ️ [Note] The line will extend approximately 0.4 in. with each stop and start of the switch trigger until the line reaches the cut-off blade and the cut-off blade cuts the excess length.

9.5 Adjust the Length of the Cutting Line Manually

1. Stop the machine. Remove the battery from the unit.
2. Push the spool retainer button (1) and pull on cutting line to manually advance the cutting line.
3. After you extend new cutter line, always return the machine to its normal position before you start it again.

9.6 Operation Tips

⚠️ [Warning] Keep clearance between the body and the machine.

⚠️ [Warning] Do not operate the machine without guard in place.

Tips when using the machine:

• Keep a firm hold with the two hands on the machine while you operate the machine.
• Cut tall grass from the top down.

If grass winds around the trimmer head:

• Remove the battery pack.
• Remove the grass.

9.7 Cutting Tips

• Tilt the machine toward the area to be cut. Use the tip of the cutting line to cut grass.
• Move the machine from right to left to prevent thrown debris from hitting the operator.
• Do not cut in the danger area.
• Do not force the trimmer head into uncut grass.
• Wire and picket fences cause cutting line wear and breakage. Stone and brick walls, curbs, and wood can wear the cutting line quickly.

Diagram description: Shows a cutting area with labels for "DANGEROUS CUTTING AREA", "BEST CUTTING AREA", and "DIRECTION OF ROTATION".

9.8 Line Cut-off Blade

This trimmer is equipped with a line cut-off blade (1) on the guard. The line cut off blade continuously trims the line to ensure a consistent and efficient cut diameter. Advance line whenever you hear the engine running faster than normal, or when trimming efficiency diminishes. This will maintain best performance and keep line long enough to advance properly.

10 Maintenance

❗ [Important] Read and understand the safety regulations and the maintenance instructions before you clean, repair or do the maintenance work on the machine.

❗ [Important] Make sure that all nuts, bolts and screws are tight. Examine regularly that you install the handles tightly.

❗ [Important] Use only the replacement parts and accessories of the initial manufacturer.

10.1 General Information

❗ [Important] Only your dealer or approved service center can do the maintenance that is not given in this manual.

Before the maintenance operations:

• Stop the machine.
• Remove the battery pack.
• Cool the motor.
• Store the machine in cool and dry place.
• Use correct clothing, protective gloves and safety glasses.

10.2 Clean the Machine

• Clean the machine after use with a moist cloth dipped in neutral detergent.
• Do not use aggressive detergents or solvents to clean the plastic parts or handles.
• Keep the trimmer head free of grass, leaves, or excessive grease.
• Keep the air vents clean and free of debris to avoid overheating and damage to the motor or the battery.
• Do not spray water onto the motor and electrical components.

10.3 Replace the Spool

1. Push the tabs on the sides of the trimmer head at the same time.
2. Pull and remove the spool cover.
3. Remove the remaining spool.
4. Put the spool in the spool housing.

ℹ️ [Note] Make sure that you put the cutting line in the slot on the new spool and extend the line approximately 15 cm before you install the new spool.

5. Put the ends of the cutting lines through the holes.
6. Extend the cutting line to release it from the guide slot in the spool.
7. Push the tabs and install the spool cover onto the spool housing.
8. Push the spool cover until it clicks into position.

10.4 Replace the Cutting Line

ℹ️ [Note] Remove the remaining cutting line on the spool.

ℹ️ [Note] Use only with the nylon cutting line of 0.065" (1.65 mm) diameter.

1. Cut two pieces of cutting line approximately 3m long of each.
2. Bend one end of the line 1/4 of an inch (6.35mm) .
3. Put the lines into the anchor holes of the spool.
4. Wind the cutting lines around the spool tightly in the indicated direction.
5. Put the cutting lines in the guide slots.
6. Do not wind the cutting line beyond the edge of the spool.

11 Transportation and Storage

⚠️ [Warning] Remove the battery pack from the machine before tranportation and storage.

11.1 Move the Machine

When you move the machine, you must:

• Wear gloves.
• Stop the machine.
• Remove the battery pack.

11.2 Store the Machine

• Remove the battery pack from the machine.
• Make sure that children cannot come near the machine.
• Keep the machine away from corrosive agents such as garden chemicals and de-icing salts.
• Secure the machine during transportion to prevent damage or injury. Clean and examine the machine for any damage.

12 Troubleshooting

13 Technical Data

Recommended Ambient Temperature Range:

14 Limited Warranty

Greenworks hereby warranties this product, to the original purchaser with proof of purchase, for a period of three (3) years against defects in materials, parts or workmanship. Greenworks, at its own discretion will repair or replace any and all parts found to be defective, through normal use, free of charge to the customer. This warranty is valid only for units which have been used for personal use that have not been hired or rented for industrial/commercial use, and that have been maintained in accordance with the instructions in the owners' manual supplied with the product from new.

Items Not Covered by Warranty:

• Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper maintenance, or alteration; or
• The unit, if it has not been operated and/or maintained in accordance with the owner's manual; or
• Normal wear, except as noted below;
• Routine maintenance items such as lubricants, blade sharpening;
• Normal deterioration of the exterior finish due to use or exposure.

Helpline:

Warranty service is available by calling our toll-free helpline, at 1-888-909-6757.

Transportation Charges:

Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. It is the purchaser's responsibility to pay transportation charges for any part submitted for replacement under this warranty unless such return is requested in writing by Greenworks.

USA address: Greenworks Tools, P.O. Box 1238, Mooresville, NC 28115

Canadian address: Greenworks Tools Canada Inc., 1110 Stellar Drive Unit 102, Newmarket, ON, L3Y 7B7

15 Exploded View

The exploded view diagram shows the assembly of the string trimmer. The parts list below identifies each component: