Matchmaster - 4G/5G Ready Digital TV Antenna and Commercial Headend Specialists
Instruction Manual for Matchmaster models including: 14MM-DTM2, 14MM-DTM2 TV Reception Systems, TV Reception Systems, Reception Systems, Systems
PAGE 2 OF 2 | AU SUPPORT 1800 237 425 WWW.MATCHMASTER.COM.AU | NZ SUPPORT 0800 237 425 WWW.MATCHMASTER.CO.NZ Note: Display indication
File Info : application/pdf, 2 Pages, 206.43KB
DocumentDocument14MM-DTM2 INSTRUCTION MANUAL CONTENTS 1 General 1.1 Description 1.2 Specifications 2 Installation 2.1 Power Supply 2.1.1 Operation via External Power Supply 2.2 Connection 2.2.1 Connection Diagram Examples 2.3 Navigation and Edition of Values 3 Operating Instructions 3.1 Description of Controls and Components 3.2 Starting 3.3 Configuration Menu 3.4 Menu Tree 1 GENERAL 1.1 Description The 14MM-DTM2 modulator is able to generate a signal in DVB-T format (Digital Terrestrial Television) from HDMI input. 14MM-DTM2 is an H.264 encoding, DVB-T modulator device to convert 4K Pass FHD HDMI signal to DVB-T RF out. The DTM2 is equipped with one HDMI input, one HDMI out(with 4K pass-though) and one DVB-T RF out. The 14MM-DTM2 module automatically adjusts the compression rate to the available Bandwidth using the modulation DVB-T parameters. 1.2 Specifications Source input Input Channel Video Video System Audio System Compression Video Video Resolution Video Bit Rate Audio Audio Bit Rate DVB Insertion Tables Editable Field RF Output Type Frequency MER Output level RF Level Adj. Attenuation step Connections HDMI In HDMI Out RF Output RF Input 1 HDMI 480i/p, 576i/p, 720p, 1080i/p, 4K (3840x2160 or 4096x2160) HDMI H.264 Baseline Profile Level 4.0 1080p 25 / 30 Max 18Mbps Max MPEG-2 / AAC 192 Kbit/s SDT, NIT Service Name, Network Name, Provider Name, TS ID, Network ID, Original NET ID, LCN, NIT Version, Private Data, Country 1 Multiplex DVB-T with a digital TV service 177858 MHz 30dB Min. 100dBµV 0dB ~ -30dB 1dB per step HDMI In 4K Pass Through 1 DVB-T RF output with type F female, 75 ohm RF Combiner Modulation Power Supply Display Configuration Environmental for operating Standard DVB-T (ETSI EN 300 744) Constellation QPSK, 16QAM, 64QAM Guard Interval 1/4, 1/8, 1/16, 1/32 Code Rate 1/2, 2/3, 3/4, 5/6, 7/8 FFT Carriers Mode 2K, 8K Bandwidth 6MHz, 7MHz, 8MHz, 7-8MHz 12V Adaptor LCD panel @ 2 x 16 characters (on front panel). 6 Local keys on front panel: - ENTER Key: Select parameter, or menu - L / R Keys: Move menu, or characters - Up / down: Select value of the figure, or field - MENU keys: Return to start menu Temperature range 5°C- 40°C Relative Humidity 80% @ 30°C Note To be able to see the 4K signal output from HDMI OUT (HDMI Pass through) port , the specifications requirement of connected TV listed as below: - 4K Ultra HD (3840x2160) Resolution - HDMI 2.0 - HDCP 2.2 - Support 4K50P/60P - HDMI 2.0 Cable *Specifications subject to change without prior notice. 2 INSTALLATION 2.1 Power Supply To start using it, connect the external power supply to the 100~230V mains and the 12V to the instrument input. Once connected to power, the device turns on and it takes about 37 seconds to be operational. Then the message "Keyboard Locked" appears on the display. 2.1.1 Operation via external power supply Use only the external power adapter supplied with the instrument. 2.2 Connection 2.2.1 Connection diagram examples Connection diagram for one module 1 2 3 4 1. TV with DVB-T built in or DVB-T STB 2. RF Combiner 3. HDMI Out (4K Pass Through) 4. HDMI In (Media Device) 5. USB (S/W update) 6. DC 12V 5 6 ATTENTION! For this configuration you should use output frequencies different from the ones that your TV is currently using. 2.3 Navigation and edition of values. The instrument is configured through its 6 keys and front panel display. In general, it is not necessary to configure the instrument to generate a DVB-T signal compatible with any digital terrestrial television receiver. Enter Button - Select parameter/menu Left/Right Button - Move left/right between menu/characters Up/Down Button - Increase/decrease value of the figure/field Menu Button - Return to start menu PAGE 1 OF 2 | AU SUPPORT 1800 237 425 WWW.MATCHMASTER.COM.AU | NZ SUPPORT 0800 237 425 WWW.MATCHMASTER.CO.NZ 3 OPERATING INSTRUCTIONS 3.1 Description of controls and components 1 2 3 4 5 6 7 8 1. Display (LCD). 2. Menu navigation keys. 3. TV COFDM Output. 4. RF Combiner 5. 4K Pass Through 6. HDMI IN 7. USB: S/W update 8. Input 12V DC power adapter (included). Note: Display indication The resolution of the LCD Display is representative of the video resolution of the RF output. Please refer to below table: HDMI In LCD Display 3840x2160p50/60 1920x1080p50/60 1920x1080p24 1920x1080i50/60 1280x720p50/60 720x576p50 720x576i50 720x480p60 720x480i60 1920x1080p50/60 1920x1080p50/60 1920x1080p24 1920x1080i50/60 1280x720p50/60 720x576p50 720x576i50 720x480p60 720x480i60 RF Out 1920x1080p25/30 1920x1080p25/30 1920x1080p24 1920x1080i50/60 1280x720p50/60 720x576p50 720x576i50 720x480p60 720x480i60 HDMI Out (HDMI Pass through) 3840x2160p50/60 1920x1080p50/60 1920x1080p24 1920x1080i50/60 1280x720p50/60 720x576p50 720x576i50 720x480p60 720x480i60 3.2 Starting 1. After connecting the power to the instrument, the message "Initial...." "Please Wait..." appears for 37 seconds. 2. Then the message "Keyboard Locked" appears. To access to the configuration menus the user has to enter a password. 3. Press ENTER. 4. The field "Enter Password" appears. Enter the access code. (By default: 0000). 5. Press ENTER. 6. The field "Network Setting" appears, this is the first option on the configuration menu. 3.3 Configuration menu 1. Frequency: It sets the frequency value for the output signal. Important: Check that the selected frequency is not already being used by a current television distribution channel. 2. RF Level Adj: It adjusts the power level of the output signal, in dB units. Its range from 0 to -30 dB. 3. Bandwidth: Channel bandwidth. (6, 7 , 8 ,7-8MHz). 4. FFT Carriers: Signal transmission mode. (2K,8K). 5. Guard Interval: Safety signal margin. (1/4, 1/8, 1/16, 1/32). 6. Constellation: Constellation type used to transmit signal(QPSK,16QAM, 64QAM). 7. Code Rate: Available values are (1/2, 2/3, 3/4, 5/6, 7/8). 8. Video Output: Video encode. H.264 of the video output. 9. Audio Output: Audio encode. Selection between MPEG-2 and AAC 10. Video Bitrate: Select video bit rate(2-18Mbps). 11. Audio Bitrate: Bitrate to encode the audio. Available values are between 192 kbit/s. 12. Service Name: Service name edit. 13. Provider Name: Service provider name edit. 14. Service ID: Service ID edit. 15. LCN: It specifies the index for the service sorting on the digital terrestrial television receiver. Values are between 1 and 999. 16. Country: Country selection for LCN sorting. 17. Original Net ID: Identifier of the original network. It is the number to identify the network from where the signal comes. 18. Network ID: It is the number that identifies the network where the signal is distributed. 19. Network Name: Network name edit. 20. TS ID: It is the transport stream identifier. 21. NIT Version: Network Information Table version. In some countries it should match with other tables version received from the receiver. 22. Information: It shows the firmware version installed in the instrument. This option is not editable. 23. Apply Setting: It saves the current configuration on the non-volatile memory of the instrument. 24. New Password: It allows the user to change to a new password to access the menu. 25. Load Default: It returns to the default values. 3.4 Menu Tree Main Layer 1 Layer 2 Menu Options Network Setting 1 Country Australia Australia, Croatia, Czech, Denmark, Estonia, Finland, France, Ireland, Italy, Latvia, Netherlands, New Zealand, Norway, Poland, Portugal, Slovak, Sweden, UK, Other 2 Original Net ID 12801 3 Network ID 12803 4 Network Name Private Network 5 TS ID 5001 6 NIT Version 28 CH & Enc Setting 1 Service Name Video 1 2 Provider Name MMTV 3 Service ID 1 4 LCN 400 1~999 5 Video Output H.264 6 Audio Output MPEG-2 AAC/MPEG-2 7 Video Bitrate 12Mbps 2~18Mbps 8 Audio Bitrate 192Kbps RF Setting 1 Frequency CH28 529.5MHz 177~857MHz 2 Constellation 64QAM QPSK, 16QAM, 64QAM 3 Guard Interval 1/16 1/4, 1/8, 1/16, 1/32 4 Code Rate 3/4 1/2, 2/3, 3/4, 5/6, 7/8 5 FFT Carrier 8K 2K, 8K 6 Bandwidth 7MHz 6, 7, 8MHz 7 RF Level Adj. 00dB 0dB ~ -30dB Information 1 FW APP 5.1.2.x.xxx.xx.xx.xx Load Default 1 Yes, No Change Password 1 0000 Network Setting Country Original Net ID Network ID Network Name TS ID NIT Version CH&Enc Setting Service Name Provider Name Service ID LCN Private Data Specifier Descriptor tag 0x05 Audeo Output RF Setting Frequency Constellation Guard Interval Code Rate FFT Carrier Bandwidth RF Level Adj CH25 Default NEW ZEALAND 8746 13313 Private Network 101 28 NEW ZEALAND LCN 8746 13313 Private Network 101 28 HDMI 1 MMTV 101 1 0 MPEG-2 HDMI 1 MMTV 101 1 0x00000037 MPEG-2 506.00MHz 64QAM 1/16 3/4 8K 8MHz 30dB 506.00MHz 64QAM 1/16 3/4 8K 8MHz 30dB PAGE 2 OF 2 | AU SUPPORT 1800 237 425 WWW.MATCHMASTER.COM.AU | NZ SUPPORT 0800 237 425 WWW.MATCHMASTER.CO.NZ