HILTI Country selectorHILTI Country selector
Instruction Manual for HILTI models including: NPR 019 IE-A22, Cordless Hydraulic Pipe Press Tools, Hydraulic Pipe Press Tools, Pipe Press Tools, NPR 019 IE-A22, Press Tools
ÐоиÑк в библиоÑеке ÑÐµÑ Ð½Ð¸ÑеÑкой докÑменÑаÑии - Hilti ÐиÑва
en zoeken in technische bibliotheek - Hilti België
Technical Library Search - Hilti Canada
File Info : application/pdf, 76 Pages, 2.85MB
DocumentDocumentNPR 019 IE-A22
English
1
12
26
37
48
58
1
2 3 4
NPR 019 IE-A22
en
Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
ru
. . . . . . . . . . . . . . . . . . . . 12
ja
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
ko
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
zh
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
cn
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Original operating instructions
1
Information about the documentation
1.1 About this documentation
· Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product.
· Observe the safety instructions and warnings in this documentation and on the product. · Always keep the operating instructions with the product and make sure that the operating instructions
are with the product when it is given to other persons.
1.2 Explanation of symbols
1.2.1 Warnings Warnings alert persons to hazards that occur when handling or using the product. The following signal words are used:
DANGER DANGER ! Draws attention to imminent danger that will lead to serious personal injury or fatality.
WARNING WARNING ! Draws attention to a potential threat of danger that can lead to serious injury or fatality.
CAUTION CAUTION ! Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the
equipment or other property.
1.2.2 Symbols in the operating instructions The following symbols are used in these operating instructions:
Comply with the operating instructions
Instructions for use and other useful information
Dealing with recyclable materials
Do not dispose of electric equipment and batteries as household waste
Hilti Liion battery Hilti charger
1.2.3 Symbols in illustrations The following symbols are used in illustrations:
These numbers refer to the illustrations at the beginning of these operating instructions. The numbering reflects the sequence of operations shown in the illustrations and may deviate from the steps described in the text. Item reference numbers are used in the overview illustration and refer to the numbers used in the key in the product overview section. These characters are intended to specifically draw your attention to certain points when handling the product.
*2207113* 2207113
English
1
1.3 Symbols on the product 1.3.1 Product-dependent symbols The following symbols can be used on the product:
Risk of crushing injury!
Direct current (DC)
The power tool supports near-field communication (NFC) technology, which is compatible with iOS and Android platforms.
Li-ion battery
Hilti Li-ion battery type series used. Observe the information given in the section headed Intended use.
Never use the battery as a striking tool.
Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any other way. If applied on the product, the product has been certified by this certification body for the US and Canadian markets according to the applicable standards.
1.4 Product information
products are designed for professional users and only trained, authorized personnel are permitted to operate, service and maintain the products. This personnel must be specifically informed about the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by untrained personnel or if used not in accordance with the intended use.
The type designation and serial number are printed on the rating plate.
Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product.
Product information
Crimping / pressing tool
NPR 019 IE-A22
Generation
01
Serial no.
1.5 Declaration of conformity
The manufacturer declares, on his sole responsibility, that the product described here complies with the applicable legislation and standards. A copy of the declaration of conformity can be found at the end of this documentation. The technical documentation is filed here: Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D-86916 Kaufering, Germany
2
Safety
2.1 General power tool safety warnings
WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Work area safety Keep work area clean and well lit. Cluttered or dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
2
English
2207113 *2207113*
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical safety Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
Personal safety Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
Power tool use and care Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
*2207113* 2207113
English
3
Battery tool use and care Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with another battery pack.
Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130° C (265 °F) may cause explosion.
Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
Service Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
2.2 Additional safety instructions for pressing tools
Personal safety Use the product only if it is in perfect working order. Never tamper with or modify the tool in any way. Never carry out crimping / pressing work on parts of a gas supply network unless express approval has
been given by the system supplier for use of this tool in conjunction with specially tested and approved fittings. If you notice oil escaping, cease working with the tool and consult Hilti Service. Immediately remove the leaked oil. Check that the locking pin is pushed in all the way and securely engaged. Make sure that there are no foreign objects (e.g. plaster, grit particles, metal cuttings, etc.) in the crimping / pressing jaws and no parts are damaged. Do not continue to use damaged or distorted crimping / pressing jaws! Throughout the crimping / pressing operation, take great care to keep your hands and fingers well clear of the crimping / pressing head. Switch the crimping / pressing tool on only after bringing it to the working position. Always hold the crimping / pressing tool firmly with both hands on the grips provided for the purpose. Keep the retaining strap and the tether clean and dry. Before starting work, check the crimping / pressing tool and the NPR PM crimping / pressing jaws in accordance with the instructions. Inadequately tested tools and jaws can lead to substandard crimpings / pressings and are a potential safety risk for the operator. Crimping / pressing tools must undergo inspection by Hilti service at the latest every 15,000 crimping / pressing operations and at least once a year. Crimping / pressing jaws must undergo servicing by Hilti service at least once a year. After crimping / pressing, pressure-test the tubing system to ensure that it is free of leaks (resulting from misuse of the tool, for example).
Electrical safety Before use of the power tool, all live cables or other items carrying electric voltage within the area in which
the user is working are to be switched off. If this is not possible, the corresponding safety precautions for working in proximity to live cables or equipment must be implemented and observed. Before using the crimping / pressing tool, make sure there are no concealed electric cables or gas or water pipes in the working area. External, metallic or electrically live parts can give you an electric shock if you inadvertently damage electric cables or gas or water pipes. Do not crimp live parts. The tool must be considered to be uninsulated and must therefore be used in conjunction with personal protective equipment (protective gloves, protective footwear, protective clothing, etc.) of a type suitable to provide protection for yourself and other persons in the vicinity.
4
English
2207113 *2207113*
Power tool use and care After approx. 50 consecutive crimping / pressing operations, switch the power tool off and allow it to
cool down for about 15 minutes. Overheating can lead to damage to the power tool.
2.3 Careful handling and use of batteries
Comply with the following safety instructions for the safe handling and use of Li-ion batteries. Failure to comply can lead to skin irritation, severe corrosive injury, chemical burns, fire and/or explosion.
Use only batteries that are in perfect working order. Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely
harmful to health! Do not under any circumstances modify or tamper with batteries! Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C
(176 °F). Never use or charge a battery that has suffered an impact or been damaged in any other way. Check
your batteries regularly for signs of damage. Never use recycled or repaired batteries. Never use the battery or a battery-operated power tool as a striking tool. Never expose batteries to the direct rays of the sun, elevated temperature, sparking, or open flame. This
can lead to explosions. Do not touch the battery poles with your fingers, tools, jewelry, or other electrically conductive objects.
This can damage the battery and also cause material damage and personal injury. Keep batteries away from rain, moisture and liquids. Penetrating moisture can cause short circuits,
electric shock, burns, fire and explosions. Use only chargers and power tools approved for the specific battery type. Read and follow the relevant
operating instructions. Do not use or store the battery in explosive environments. If the battery is too hot to touch, it may be defective. Put the battery in a place where it is clearly visible
and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to cool down. If it is still too hot to touch after an hour, the battery is faulty. Consult Hilti Service or read the document entitled "Instructions on safety and use for Hilti Li-ion batteries".
Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries. page 10 Read the instructions on safety and use of Hilti Li-ion batteries that you can access by scanning the QR code at the end of these operating instructions.
3
Description
3.1 Product overview 1
@ Crimping / pressing head ; Piston return switch to open the crimping /
pressing jaws in the event of a fault or emergency
= Casing % Servicing and fault indicator (red LED) & Battery release button ( Battery ) Slot on both sides to fasten the Hilti retaining
leash
+ White LED to illuminate the working area § Control switch / Locking pin for opening/closing the tool head : Crimping / pressing jaws
3.2 Intended use The product described is a cordless electro-hydraulic crimping tool.
*2207113* 2207113
English
5
It is designed for crimping fittings used to connect composite, copper (Cu) and steel pipes.
· Use only Hilti lithiumion batteries of the B 22 series with this product. · Use only Hilti-approved battery chargers to charge these batteries. More information is available from
your Hilti Store or from www.hilti.group
3.3 Lithiumion battery status display
The charge state of the Li-ion battery and malfunctions of the product are indicated by the indicator of the Liion battery. The state of charge of the Liion battery is displayed after pressing one of the two battery release buttons.
Status 4 LEDs light. 3 LEDs light. 2 LEDs light. 1 LED lights. 1 LED flashes.
Meaning State of charge: 75 % to 100 % State of charge: 50 % to 75 % State of charge: 25 % to 50 % State of charge: 10 % to 25 % State of charge: < 10 %
Battery state of charge cannot be displayed while the control switch is pressed and for up to 5 seconds after releasing the control switch. If the LEDs of the charge state indicator flash, follow the instructions in the 'Troubleshooting' section.
3.4 Items supplied
Crimping / pressing tool, operating instructions. Other system products approved for use with this product can be found at your local HILTI STORE or online at: www.hilti.group
4
Technical data
Rated voltage Weight in accordance with EPTA Procedure 01 including batteryB22/8.0 Crimping time Max. crimping force Storage temperature Ambient temperature for operation
NPR 019 IE-A22 21.6 V 2.7 kg 4s 19 kN -20 ... 70 -17 ... 60
4.1 Noise information and vibration values in accordance with EN 62841
The sound pressure and vibration values given in these instructions were measured in accordance with a standardized test and can be used to compare one power tool with another. They can also be used for a preliminary assessment of exposure.
The data given represent the main applications of the power tool. However, if the power tool is used for different applications, with different accessory tools, or is poorly maintained, the data can vary. This can significantly increase exposure over the total working period.
An accurate estimation of exposure should also take into account the times when the tool is switched off, or when it is running but not actually being used for a job. This can significantly reduce exposure over the total working period.
Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for example: maintaining the power tool and accessory tools, keeping the hands warm, organization of work patterns.
Noise values
Sound (power) level (L WA) Uncertainty for the sound power level (K WA) Emission sound pressure level (L pA) Uncertainty for the sound pressure level (K pA)
80 dB(A) 2.5 dB(A) 70 dB(A) 2.5 dB(A)
6
English
2207113 *2207113*
Vibration values Total vibration (during operation) (a) Uncertainty (K)
2.5 m/s² 1.5 m/s²
4.2 Battery
Battery operating voltage Ambient temperature Storage temperature
21.6 V -17 ... 60 -20 ... 40
5
Preparations at the workplace
WARNING Risk of injury by inadvertent starting! Before inserting the battery, make sure that the product is switched off. Remove the battery before making any adjustments to the power tool or before changing accessories.
Observe the safety instructions and warnings in this documentation and on the product.
5.1 Charging the battery
1. Before charging the battery, read the operating instructions for the charger. 2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry. 3. Use an approved charger to charge the battery. page 5
5.2 Inserting the battery
WARNING Risk of injury by short circuit or falling battery! Before inserting the battery, make sure that the contacts on the battery and the contacts on the product
are free of foreign matter. Make sure that the battery always engages correctly.
1. Charge the battery fully before using it for the first time. 2. Push the battery into the product until it engages with an audible click. 3. Check that the battery is seated securely.
5.3 Removing the battery
1. Press the battery release buttons. 2. Remove the battery from the tool.
5.4 Fall arrest
WARNING Risk of injury by falling tool and/or accessory! Use only the Hilti tool tether recommended for your product. Prior to each use, always check the attachment point of the tool tether for possible damage.
Comply with the national regulations for working at heights.
As drop arrester for this product, use only a combination of the Hilti retaining strap and the Hilti tool tether #2261970.
Secure the retaining strap to the installation openings for accessories. Check that it holds securely.
*2207113* 2207113
English
7
Secure one carabiner of the tool tether to the retaining strap and secure the second carabiner to a load-bearing structure. Check that both carabiners hold securely.
Comply with the operating instructions of the Hilti retaining strap and those of the Hilti tool tether.
5.5 Inserting the crimping / pressing jaws 2
CAUTION Risk of injury! The accessory tool may be hot and/or have sharp edges. Wear protective gloves when changing the accessory tool. Never lay down a hot accessory tool on a flammable surface.
WARNING Risk of injury! Unintentional starting. Remove the battery before fitting, changing or removing the crimping / pressing jaws.
Never operate the product without the crimping / pressing jaws installed! To ensure correct crimping / pressing and reliable and safe operation, use only the crimping / pressing jaws approved by the system provider and/or machine manufacturer.
1. Remove the battery and select the appropriate crimping / pressing jaws. 2. Press the locking pins. 3. Rotate the locking pins counterclockwise as far as they will go. 4. Pull out the locking pins. 5. Insert the crimping / pressing jaws. 6. Push the locking pins in until they engage. 7. Rotate the crimping / pressing head to the desired working position.
The crimping / pressing head can be rotated much more easily when not under pressure.
5.6 Removing the crimping / pressing jaws 3
WARNING Risk of injury! Unintentional starting. Remove the battery before fitting, changing or removing the crimping / pressing jaws.
1. Remove the battery and rotate the crimping / pressing head into the outset position. 2. Press the locking pins. 3. Rotate the locking pins counterclockwise as far as they will go. 4. Pull out the locking pins. 5. Work the crimping jaws forward and out of the product.
6
Operation
Observe the safety instructions and warnings in this documentation and on the product.
6.1 Crimping / pressing 4
DANGER Electric shock hazard! Working in adverse outdoor conditions can cause electric shocks and/or short circuits. Never work on electrically live lines while a thunderstorm is in progress. Call a halt to work immediately whenever weather conditions impair the insulation characteristics, vision
or movement of the workers.
8
English
2207113 *2207113*
WARNING Risk of injury due to oil escaping under high pressure! Oil escaping under high pressure can injure the skin and the eyes. Do not use the pressing tool if damage is visible. Do not use the pressing tool if oil escapes. Make sure that the piston retracts after every pressing operation. If the piston does not retract after the pressing operation, press the reset button for manual retraction.
WARNING Danger! Risk of causing gas leakage when carrying out crimping / pressing work on parts of a gas supply network! Never carry out crimping / pressing work on parts of a gas supply network unless express approval has
been given by the system supplier for use of this tool in conjunction with specially tested and approved fittings.
WARNING Risk of injury due to flying fragments! Flying fragments present a risk of injury to the eyes and body. Wear eye protection and protective gloves. Use suitable connecting material in combination with the correct pressing rings and pressing / adapter
jaws. Before and during the pressing operation, make sure that the pressing rings and pressing / adapter jaws
are correctly positioned.
CAUTION Damage to property due to incorrect handling! Incorrect handling can result in damage to the pressing tool and/or the pressing rings. Before starting work, make sure that the pressing rings are dust-free. Before starting work, lubricate the pressing rings and - if present - the rolling actuator with lubricant and
corrosion-inhibiting spray (#308976). Comply with the original operating instructions of the manufacturer.
In order to achieve a tight, durable crimped / pressed joint, it is essential that the crimping / pressing jaws reach the fully closed position, thus indicating completion of the crimping / pressing operation. If the crimping / pressing operation is ended prematurely, the fitting must be removed or, if possible, recrimped / repressed.
In cold weather the hydraulic oil can thicken and slow the crimping / pressing operation. Perform 5 to 10 empty crimping / pressing operations to heat up the crimping / pressing tool.
1. Insert the crimping / pressing jaws. page 8 2. Squeeze the legs of the pressing jaws together.
The pressing jaw opens. 3. Enclose the fitting to be installed in the pressing jaw. 4. Press and hold down the control switch until the piston retracts.
The pressing operation is completed successfully.
7
Care and maintenance
WARNING Risk of injury with battery inserted ! Always remove the battery before carrying out care and maintenance tasks!
Care of the product · Carefully remove stubborn dirt.
*2207113* 2207113
English
9
· Carefully clean the air vents, if present, with a dry, soft brush. · Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as
these can attack the plastic parts. · Use a dry, clean cloth to clean the contacts of the product.
Care of the Liion batteries · Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush. · Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of
moisture (e.g. by being dipped in water or left in the rain). If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable container and consult Hilti Service. · Keep the battery free of extraneous oil and grease. Do not permit dust or dirt to accumulate unnecessarily on the battery. Clean the battery with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents containing silicone as these can attack the plastic parts. Do not touch the contacts of the battery and do not remove the factory-applied grease from the contacts. · Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as these can attack the plastic parts.
Maintenance · Check all visible parts and controls for signs of damage at regular intervals and make sure that they all
function correctly. · Do not use the product if signs of damage are found or if parts malfunction. Immediately have the product
repaired by Hilti Service. · After cleaning and maintenance, install all guards and protective devices and check that they are in full
working order.
To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with your product can be found at your Hilti Store or online at: www.hilti.group
8
Transport and storage of cordless tools and batteries
Transport
CAUTION Accidental starting during transport ! Always transport your products with the batteries removed!
Remove the battery/batteries. Never transport batteries loose and unprotected. During transport, batteries should be protected from
excessive shock and vibration and isolated from any conductive materials or other batteries that may come in contact with the terminals and cause a short circuit. Comply with the locally applicable regulations for transporting batteries. Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged batteries. Prior to each use and before and after prolonged transport, check the product and the batteries for damage.
Storage
WARNING Accidental damage caused by defective or leaking batteries ! Always store your products with the batteries removed!
Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in the technical data.
Do not store batteries on the charger. Always remove the battery from the charger when the charging operation has completed.
Never leave batteries in direct sunlight, on sources of heat, or behind glass. Store the product and batteries where they cannot be accessed by children or unauthorized persons. Prior to each use and before and after prolonged storage, check the product and the batteries for
damage.
10 English
2207113 *2207113*
9
Troubleshooting
If the trouble you are experiencing is not listed in this table or you are unable to rectify the problem by yourself, please contact Hilti Service.
9.1 The crimping / pressing tool is not in working order.
Malfunction
The LEDs on the battery indicate nothing.
Possible cause The battery is not correctly inserted.
Battery is discharged.
The battery is too hot or too cold.
1 LED on the battery blinks. Battery is discharged. The battery is too hot or too cold.
4 LEDs on the battery blink.
Red LED => lights continuously and a warning tone is emitted.
Red LED => blinks at short intervals and a warning tone is emitted.
Red LED => lights briefly and no warning tone is emitted.
Product momentarily overloaded. Technical problem.
The state of charge of the battery is too low to allow a complete operating cycle. Product overheated.
Action to be taken Push the battery in until it
engages with a double click. Change the battery and charge
the empty battery. Allow the battery to cool
down or to warm up to room temperature. Change the battery and charge the empty battery. Allow the battery to cool down or to warm up to room temperature. Allow the product to cool down. Incorrect operation is possible! Contact Hilti Service.
Change the battery and charge the empty battery.
Allow the product to cool down.
9.2 The crimping / pressing tool is in working order.
Trouble or fault
The battery runs down more quickly than usual.
The battery does not engage with an audible double click.
Red LED => blinks at long intervals and a warning tone is emitted.
Red LED => lights continuously and a warning tone is emitted.
Red LED => lights continuously and no warning tone is emitted.
Possible cause Very low ambient temperature.
The retaining lugs on the battery are dirty. Crimping / pressing pressure not achieved (tool was used incorrectly). Technical problem.
Product maintenance necessary.
Action to be taken Allow the battery to warm up
slowly to room temperature. Clean the retaining lugs and refit
the battery. Make sure that the tool is
used correctly and check the crimping / pressing if unsure. Incorrect operation is possible! Contact Hilti Service.
Contact Hilti Service.
10 Disposal
WARNING Risk of injury due to incorrect disposal! Health hazards due to escaping gases or liquids. DO NOT send batteries through the mail! Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting. Dispose of your battery out of the reach of children. Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public
health and safety resources for disposal instructions.
*2207113* 2207113
English 11
Most of the materials from which Hilti products are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti sales representative for further information.
Do not dispose of power tools, electronic equipment or batteries as household waste!
11 RoHS (Restriction of Hazardous Substances) Click on the link to go to the table of hazardous substances: qr.hilti.com/r7794691. There is a link to the RoHS table, in the form of a QR code, at the end of this document.
12 Manufacturer's warranty Please contact your local Hilti representative if you have questions about the warranty conditions.
1
1.1
· (RU)
" ", 141402, , . , . , . 25 · (BY)
222750, , , -1, 18- , 2 ( . ), 1-34 · (KZ) , 050011, . , . 4 · (KG) OcOO "T AND T", 720021, , ,. 29 · (AM) -, , . , . 10/1
: . . : . . : www.hilti.ru , , , . 10 .
· . .
· , .
· .
1.2
1.2.1 . :
12
2207113 *2207113*
! ,
.
! ,
.
! ,
( ).
1.2.2 , :
,
!
Hilti - (Li-Ion) Hilti
1.2.3 :
. , . . . .
1.3 1.3.1 :
!
NFC, iOS Android.
- - Hilti. , .
*2207113* 2207113
13
.
. , - . , .
1.4
,
.
.
.
.
.
.
NPR 019 IE-A22 01
1.5
- , . . . () : Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering,
2
2.1
, , , . , / . . «» , ( ) ( ).
.
. / ,
, . / , /. /. , /.
.
! . . , , , -/ . .
14
2207113 *2207113*
. .
, , . , , /. .
, , . , , .
, . .
, . , , . .
. , , , , , .
. , , / , . , , .
. , , .
. . .
. . , . , .
, , . .
, . .
. , . .
. , , .
, / . .
, . , . .
. , , -
*2207113* 2207113
15
, . . . , . , . , (), . . . . . -- . .
, -
. . , . . , , , , , . . . . . . . . , . . 130 °C . , . / .
, -
. . . .
2.2
. . ,
. , , Hilti. . , .
16
2207113 *2207113*
(, , , . .) , . !
/ .
.
.
. NPR PM
. . Hilti 15 000 , , . Hilti. , (, ).
,
. , . , - . , , , - . . ( , , . .), , .
50
15 . .
2.3
- . , , , / .
. ,
, !
! , , 80 °C (176 °F)
. , ()
- . . . . , , . . () , , . , .
*2207113* 2207113
17
, . , , , .
. , .
. (, )
. . . , , , . Hilti « - Hilti».
, . 23 - Hilti, QR- .
3
3.1 1
@
;
/
=
%
( )
&
(
) , -
Hilti
+
§
/
/
:
3.2
, , .
· - Hilti B 22.
· Hilti . . Hilti Store www.hilti.group.
3.3 -
- - . - .
.
: 75 % 100 %
18
2207113 *2207113*
. . . .
: 50 % 75 % : 25 % 50 % : 10 % 25 % : < 10 %
. 5 . « ».
3.4
, . , , HILTI STORE www.hilti.group
4
EPTA Procedure 01 B22/8.0 .
NPR 019 IE-A22 21,6 2,7 4 19 -20 ... 70 -17 ... 60
4.1 EN 62841
. .
. , , () , . .
, . .
/ , : () , , .
(L WA) (K WA) (L pA) (K pA)
80 () 2,5 () 70 () 2,5 ()
( ) (a) (K)
2,5 /² 1,5 /²
*2207113* 2207113
19
4.2
21,6 -17 ... 60 -20 ... 40
5
! , -
.
.
, .
5.1
1. . 2. , . 3. . 18
5.2
! . , .
1. . 2. ,
. 3. .
5.3
1. () . 2. .
5.4
/ ! Hilti
. -
.
.
Hilti Hilti #2261970.
. .
20
2207113 *2207113*
- , -- . .
Hilti , Hilti.
5.5 2
! / . .
.
! , // .
! / .
1. , . 2. . 3. . 4. . 5. . 6. . 7. .
.
5.6 3
! , // .
1. , . 2. . 3. . 4. . 5. .
6
, .
*2207113* 2207113
21
6.1 4
! / . . , , -
.
! . , . . , . ,
.
! ! ,
.
! . .
/ . , /
.
! / . , , . ( )
(#308976), . .
, , . , , , , .
. 5 10 , .
1. . 21 2. .
. 3. .
22
2207113 *2207113*
4. . .
7
! !
· . · ( ) . · .
, . · .
- · .
. · .
(, ). , , . Hilti. · , . . . , . , . · . , .
· ,
-- . · / . -
Hilti. ·
.
. Hilti , Hilti Store : www.hilti.group
8
! !
().
( ). , , , . .
. - , .
*2207113* 2207113
23
, .
! !
. , .
. .
, / .
. ,
.
9
, , Hilti.
9.1
.
.
.
/
.
.
/
.
=> .
=> .
=> .
. .
.
.
() . . . . . .
! Hilti.
.
.
24
2207113 *2207113*
9.2
, .
() .
=> .
=> .
=> .
( ). .
.
. . .
! Hilti.
Hilti.
10
! . ! ,
. , . Hilti Store
.
, Hilti, . ( ). Hilti (, ) . Hilti.
, / !
11 RoHS ( ) : qr.hilti.com/r7794691. QR- RoHS . .
12 Hilti.
*2207113* 2207113
25
1
1.1
·
· ·
1.2 1.2.1
1.2.2
Hilti Li-Ion Hilti
1.2.3
26
2207113 *2207113*
1.3 1.3.1
iOS Android NFC
Li-Ion
Hilti Li-Ion
1.4
NPR 019 IE-A22
01
1.5
Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE
2
2.1
*2207113* 2207113
27
28
2207113 *2207113*
130 °C265 °F
2.2
Hilti
NPR PM
15,000 1 1 Hilti 1 1 Hilti
*2207113* 2207113
29
50 15
2.3
Li-Ion
80°C176°F
1 Hilti Hilti Li-Ion
Li-Ion 35 QR Hilti Li-Ion
3
3.1 1
@
;
=
%
LED
&
(
) Hilti
+ LED
§
/
:
30
2207113 *2207113*
3.2
Cu
· Hilti B 22 Li-Ion · Hilti
Hilti Store www.hilti.group
3.3 Li-Ion
Li-Ion Li-Ion Li-Ion 2
4 LED 3 LED 2 LED 1 LED 1 LED
75 %...100 % 50 %...75 % 25 %...50 % 10 %...25 % < 10 %
5 LED
3.4
HILTI STORE www.hilti.group
4
EPTA Procedure 01 B22/8.0
NPR 019 IE-A22 21.6 V 2.7 kg 4s 19 kN -20 ... 70 -17 ... 60
4.1 EN 62841
(L WA) (K WA)
80 dB(A) 2.5 dB(A)
*2207113* 2207113
31
(L pA) (K pA) (a) (K)
4.2
70 dB(A) 2.5 dB(A)
2.5 m/s² 1.5 m/s²
21.6 V -17 ... 60 -20 ... 40
5
5.1
1. 2. 3. 31
5.2
1. 2. 3.
5.3
1. 2.
5.4
Hilti
32
2207113 *2207113*
Hilti Hilti #2261970
2
Hilti Hilti
5.5 2
1. 2. 3. 4. 5. 6. 7.
5.6 3
1. 2. 3. 4. 5.
6
*2207113* 2207113
33
6.1 4
#308976
5...10
1. 33 2.
3. 4.
34
2207113 *2207113*
7
· · ·
·
Li-Ion ·
·
Hilti · ·
·
· Hilti
·
Hilti Hilti Store www.hilti.group
8
*2207113* 2207113
35
9
Hilti
9.1
LED
1 LED
4 LED LED=> LED=> LED=>
Hilti
9.2
LED=>
36
2207113 *2207113*
LED=>
LED=>
Hilti
Hilti
10
Hilti Store
Hilti Hilti Hilti
11 RoHS qr.hilti.com/r7794691 RoHS QR
12 Hilti
1
1.1
· . .
· . · .
1.2 1.2.1 . .
! .
.
*2207113* 2207113
37
! .
.
! . .
1.2.2 .
Hilti Hilti
1.2.3 .
. , . , . , .
1.3 1.3.1 .
!
iOS Android NFC .
Hilti . .
. . . , .
38
2207113 *2207113*
1.4
, , . . .
.
. .
NPR 019 IE-A22
01
1.5
. . . Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE
2
2.1
, , . , / . . " " ( ) ( ) .
.
. , .
. , .
.
. .
. . , , , . . . . , . , , . . , . . , . .
. .
, . . . , , , .
*2207113* 2207113
39
. / , OFF . .
, . .
. , . .
. . , . , .
, . .
. .
. .
, .
. , .
, / . .
. . .
. , , . . .
. .
, , . . , .
, . .
.
.
. , .
, , , , . .
, . . , . , . , .
. , .
. 130 °C (265 °F) .
. .
.
.
. .
40
2207113 *2207113*
2.2
. .
. Hilti .
. . (: , , )
. ! . . . . NPR PM .
. 15,000 , 1 Hilti . Hilti . ( ) .
. . . , . . , (, , ) .
50 15 .
.
2.3
. , , , / .
. , ! ! 80 °C (176 °F) . .
. . . , , .
. , , . ,
. . , , ,
. .
. .
*2207113* 2207113
41
. . . . Hilti " Hilti " .
, . 46 Hilti QR .
3
3.1 1
@ ;
= % ( LED) & ( ) , Hilti + LED § / / :
3.2
. , (Cu) .
· B 22 Hilti . · Hilti . Hilti Store
www.hilti.group .
3.3
. .
4 LED . 3 LED . 2 LED . 1 LED . 1 LED .
: 75 % ~ 100 % : 50 % ~ 75 % : 25 % ~ 50 % : 10 % ~ 25 % : < 10 %
5 . LED , " " .
3.4
, . HILTI STORE . www.hilti.group
42
2207113 *2207113*
4
EPTA Procedure 01 ( )B22/8.0
NPR 019 IE-A22 21.6V 2.7kg 4 19kN -20 ... 70 -17 ... 60
4.1 EN 62841
, . .
. . .
. .
/ . , , .
(L WA) (K WA) (L pA) (K pA)
80dB(A) 2.5dB(A) 70dB(A) 2.5dB(A)
( ) (a) (K)
2.5m/s² 1.5m/s²
4.2
21.6V -17 ... 60 -20 ... 40
5
! . .
.
5.1
1. . 2. . 3. . 42
*2207113* 2207113
43
5.2
! . . 1. , . 2. . 3. .
5.3 1. . 2. .
5.4
/ ! Hilti . .
.
Hilti Hilti #2261970 . . . ,
. . Hilti Hilti .
5.5 2
! / . . .
! . // .
. , .
1. , . 2. . 3. . 4. . 5. . 6. .
44
2207113 *2207113*
7. . .
5.6 3
! . // .
1. , . 2. . 3. . 4. . 5. .
6
.
6.1 4
! / . . .
! . . . .
.
! !
.
! . . . .
! / . . ( ) ((#308976)
. .
*2207113* 2207113
45
.
, .
. 5 10 .
1. . 44 2. .
. 3. . 4. .
.
7
! !
· . · , . · .
. · .
· .
. · .
(: ). , . , Hilti . · . . . . , . · . .
· ,
. · . Hilti
. · .
. Hilti , Hilti Store www.hilti.group .
8
! !
46
2207113 *2207113*
. .
. . . . .
! !
. . . . , . . .
9
Hilti .
9.1
LED .
.
.
.
1 LED .
. .
4 LED .
LED =>
. .
LED =>
LED =>
.
.
.
.
.
.
.
.
! Hilti .
.
.
9.2
.
" " .
LED =>
.
.
( ).
.
.
.
*2207113* 2207113
47
LED =>
.
LED => .
! Hilti .
Hilti .
10
! . ! . . Hilti Store .
Hilti . . Hilti . Hilti .
, !
11 RoHS ( ) . qr.hilti.com/r7794691. RoHS QR .
12 Hilti .
1
1.1
· · ·
: : 162422041 : 0800-221-036
1.2 1.2.1
!
48
2207113 *2207113*
!
1.2.2
Hilti Hilti
1.2.3
1.3 1.3.1
DC
NFCiOSAndroid
Hilti
*2207113* 2207113
49
1.4
HiltiHilti
/
NPR 019 IE-A22 01
1.5
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D-86916 Kaufering, Germany
2
2.1
/
RCD
RCD
50
2207113 *2207113*
/
130° C265 °F
2.2
Hilti
NPR PM
15,000Hilti Hilti
*2207113* 2207113
51
5015
2.3
/
80°C176°F
Hilti Hilti
57 Hilti
3
3.1 1
@ / ; /
= % LED & ( ) Hilti + LED § / / : /
3.2 Cu · B 22Hilti · HiltiHilti Storewww.hilti.group
3.3
52
2207113 *2207113*
4LED 3LED 2LED 1LED 1LED
75 %100 % 50 %75 % 25 %50 % 10 %25 % < 10 %
5LED
3.4
/ HILTI STOREwww.hilti.group
4
EPTA Procedure 01B22/8.0
NPR 019 IE-A22 21.6 V 2.7 kg 4s 19 kN -20 ... 70 -17 ... 60
4.1 EN 62841
/
(L WA) (K WA) (L pA) (K pA)
80 dB(A) 2.5 dB(A) 70 dB(A) 2.5 dB(A)
(a) (K)
2.5 m/s² 1.5 m/s²
4.2
21.6 V -17 ... 60 -20 ... 40
*2207113* 2207113
53
5
5.1
1. 2. 3. 52
5.2
1. 2. 3.
5.3
1. 2.
5.4
/ Hilti
HiltiHilti#2261970
HiltiHilti
5.5 2
54
2207113 *2207113*
/
/
1. 2. 3. 4. 5. 6. 7.
5.6 / 3
/
1. / 2. 3. 4. 5.
6
6.1 4
/
/
/
*2207113* 2207113
55
/ /
/ #308976
510
1. 54 2.
3. 4.
7
!
· · · ·
· ·
Hilti ·
·
· · / Hilti ·
HiltiHilti Store Hilti www.hilti.group
56
2207113 *2207113*
8
!
9
Hilti
9.1 /
LED
1LED
4LED
LED =>
LED =>
LED =>
Hilti
9.2 /
LED =>
/
/
*2207113* 2207113
57
LED =>
LED =>
Hilti
Hilti
10
Hilti Store
HiltiHilti Hilti
11 RoHS qr.hilti.com/r7794691 QRRoHS
12 Hilti Hilti Taiwan Co., Ltd. 24F., No. 16, Xinzhan Rd., Banqiao Dist., New Taipei City 220, Taiwan (R.O.C.) Tel. 0800221036
1
1.1
· · ·
1.2 1.2.1
-
-
58
2207113 *2207113*
-
1.2.2
Hilti Hilti
1.2.3
1.3 1.3.1
(DC)
(NFC) iOS
Hilti ""
1.4
*2207113* 2207113
59
Hilti Hilti
/
NPR 019 IE-A22
01
1.5
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D-86916 Kaufering, Germany
2
2.1
/ "" () ()
() ()
(RCD) RCD
/"" ""
60
2207113 *2207113*
/ ( )
() /
130 °C (265 °F)
()
2.2
/
Hilti ()
/ NPR PM
15,000 Hilti Hilti ()
(
)
*2207113* 2207113
61
50 15
2.3
/
80 (176 )
Hilti " Hilti "
67 Hilti
3
3.1 1
@ / ;
/
= % ( LED) & ( ) Hilti + LED § / / : /
3.2
(Cu) · Hilti B 22 · Hilti Hilti Store www.hilti.group
3.3
4 LED 3 LED
75% 100% 50% 75%
62
2207113 *2207113*
2 LED 1 LED 1 LED
25% 50% 10% 25% < 10%
5 LED ""
3.4
/ HILTI STORE www.hilti.group
4
EPTA Procedure 01 ()B22/8.0
NPR 019 IE-A22 21.6 V 2.7 kg 4s 19 kN -20 ... 70 -17 ... 60
4.1 EN 62841
/
() (L WA) (K WA) (L pA) (K pA)
80 dB(A) 2.5 dB(A) 70 dB(A) 2.5 dB(A)
() (a) (K)
2.5 m/s² 1.5 m/s²
4.2
21.6 V -17 ... 60 -20 ... 40
*2207113* 2207113
63
5
-
5.1
1. 2. 3. 62
5.2
-
1. 2. 3.
5.3
1. 2.
5.4
- Hilti
Hilti Hilti #2261970
Hilti Hilti
5.5 / 2
- /
64
2207113 *2207113*
- /
/
1. / 2. 3. 4. 5. / 6. 7. /
/
5.6 / 3
- /
1. / 2. 3. 4. 5.
6
6.1 4
- /
-
--
/ /
*2207113* 2207113
65
- / /
- / (#308976) ()
()
5 10
1. / 64 2.
3. 4.
7
- !
· · · ·
· · (
) Hilti · ·
· · / Hilti ·
Hilti Hilti Hilti Store www.hilti.group
66
2207113 *2207113*
8
-
()
- !
9
Hilti
9.1 /
LED
1 LED
4 LED
LED =>
LED =>
LED =>
Hilti
9.2 /
""
LED =>
LED =>
/ ( )
/
Hilti
*2207113* 2207113
67
LED =>
Hilti
10
- () Hilti Store
Hilti Hilti Hilti
11 RoHS () qr.hilti.com/r7794691 RoHS
12 Hilti
68
2207113 *2207113*
*2207113*
2207113
Hilti = registered trademark of Hilti Corp., Schaan
Pos. 8 | 20220427