ecler VEO-XTI1CG2 Video Distribution Over IP Instruction Manual

Instruction Manual for ecler models including: VEO-XTI1CG2, VEO-XRI1CG2, VEO-XTI1CG2 Video Distribution Over IP, VEO-XTI1CG2, Video Distribution Over IP, Distribution Over IP, Over IP

8

Enriqueta Arboli Hewlett-Packard Company

Search - Ecler Pro Audio

Resources list - Ecler Pro Audio

File Info : application/pdf, 34 Pages, 1.81MB

1718291211-ecler-veo-xri1cg2-user-manual-en

PRECAUTIONS

VEO-XTI1CG2 / VEO-XRI1CG2
VIDEO DISTRIBUTION OVER IP H.265 Full HD over IP Video Extenders

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

PANEL

FUNCTIONS

TECHNICAL

DATA

USER MANUAL

50-0430-0107

VEO-XTI1CG2 - VEO-XRI1CG2

TABLE OF CONTENTS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

1. PRECAUTIONS ........................................................................................................................3

1.1 Important Remark.................................................................................................................... 3

PRECAUTIONS

1.2 Important Safety Instructions .............................................................................................. 4

1.3 Cleaning...................................................................................................................................... 4

2. PACKAGE CONTENTS ..........................................................................................................5

2.1 VEO-XTI1CG2 .......................................................................................................................... 5

2.2 VEO-XRI1CG2 .......................................................................................................................... 5

3. DESCRIPTION and FEATURES............................................................................................6

3.1 Main Features ........................................................................................................................... 6 4. INSTALL & CONNECT............................................................................................................7

4.1 Rack Mounting in VEO-RK1CG2 ........................................................................................ 7

4.2 Network requirements and configuration ........................................................................ 8

4.2.1 4.2.2 4.2.3 4.2.4

Setting the IP address.............................................................................................................8 Video distribution Quick Start ..............................................................................................9 Unicast mode .............................................................................................................................9 Multicast mode ....................................................................................................................... 10

5. START-UP and OPERATION ............................................................................................ 11

FUNCTIONS

5.1 Configuration using Web Interface..................................................................................11

5.1.1 5.1.2 5.1.3 5.1.4 5.1.5 5.1.6

Information .............................................................................................................................. 11 Video Settings ........................................................................................................................ 12 Led.............................................................................................................................................. 16 Settings..................................................................................................................................... 17 Update....................................................................................................................................... 19 Log Out ..................................................................................................................................... 20

5.2 Remote Controlling ...............................................................................................................20

DATA

5.2.1 RS-232...................................................................................................................................... 20 5.2.2 Advanced Network Management .................................................................................... 23 6. PANEL FUNCTIONS ............................................................................................................ 24

6.1 VEO-XTI1CG2 (TX, transmitter) .......................................................................................24
6.1.1 Front Panel............................................................................................................................... 24 6.1.2 Rear Panel................................................................................................................................ 25 6.2 VEO-XRI1CG2 (RX, receiver).............................................................................................26
6.2.1 Front Panel............................................................................................................................... 26 6.2.2 Rear Panel................................................................................................................................ 27 6.3 Additional Functionalities of CH Select / buttons for both: VEO-XTI1CG2 and VEO-XRI1CG2 ........................................................................................................................28

7. TECHNICAL DATA .............................................................................................................. 31

7.1 Technical Specifications ......................................................................................................31

7.2 Mechanical Diagram .............................................................................................................33

7.2.1 VEO-XTI1CG2 ........................................................................................................................ 33 7.2.2 VEO-XRI1CG2 ........................................................................................................................ 33

PANEL

TECHNICAL

1. PRECAUTIONS

1.1 IMPORTANT REMARK

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

PANEL

FUNCTIONS

TECHNICAL

DATA

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING (If applicable): The terminals marked with symbol of " " may be of sufficient
magnitude to constitute a risk of electric shock. The external wiring connected to the terminals requires installation by an instructed person or the use of ready-made leads or cords.
WARNING: To prevent fire or shock hazard, do not expose this equipment to rain or
moisture.
WARNING: A device with Class I construction shall be connected to a mains socket-outlet
with a protective earthing connection.
WARNING: This product must not be discarded, under any circumstance, as
unsorted urban waste. Take to the nearest electrical and electronic waste treatment centre.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
3

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

1.2 IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this device near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other device (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the device.
11. Only use attachments/accessories specified by the manufacturer.

12. Unplug the device during lightening sorts or when unused for long periods of time.
13. Refer all servicing to qualified personnel. Servicing is required when the device has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the device, the device has been exposed to rain or moisture, does not operate normally, or has been dropped.
14. Disconnecting from mains: When switching off the POWER switch, all the functions and light indicators of the unit will be stopped, but fully disconnecting the device from mains is done by unplugging the power cable from the mains input socket. For this reason, it always shall remain easily accessible.
15. Equipment is connected to a socketoutlet with earthing connection by means of a power cord.
16. The marking information is located at the bottom of the unit.
17. The device shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on device.

INSTALL &
CONNECT

START-UP &
OPERATION

PANEL

FUNCTIONS

TECHNICAL

DATA

1.3 CLEANING Clean the unit with a soft, dry clean cloth or slightly wet with water and neutral liquid soap only, then dry it with a clean cloth. Be careful that water never gets into the unit through any hole. Never use alcohol, benzine, solvents or abrasive substances to clean this unit.
NEEC AUDIO BARCELONA, S.L. accepts no liability for any damage that may be caused to people, animal, or objects due to failure to comply with the warnings above.
4

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

Thank you for choosing our device Ecler VEO-XTI1CG2 and VEO-XRI1CG2! We appreciate your trust.
It is VERY IMPORTANT to carefully read this manual and to fully understand its
contents before any connection in order to maximize your use and get the best performance from this equipment. To ensure optimal operation of this device, we strongly recommend that its maintenance be carried out by our authorised Technical Services. All ECLER products are covered by warranty, please refer to www.ecler.com or the warranty card included with this product for the period of validity and conditions.
2. PACKAGE CONTENTS
2.1 VEO-XTI1CG2 · 1 x Transmitter. · 2 x 3-pin Euroblock connectors. · 4 x Screws. · 2 x Detachable mounting ear. · 1 x 12V DC power adapter with international blades. · Getting Started Guide. · Warranty card.
2.2 VEO-XRI1CG2 · 1 x Receiver. · 2 x 3-pin Euroblock connectors. · 4 x Screws. · 2 x Detachable mounting ear. · 1 x 12V DC power adapter with international blades. · Getting Started Guide. · Warranty card.
5

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

3. DESCRIPTION and FEATURES
VEO-XTI1CG2 transmitter and VEO-XRI1CG2 receiver are a H.265 / H.264 over IP set of extenders that allow for HDMI distribution over 1Gb Ethernet networks with up to 1080p@60Hz video support. These devices represent a professional high-quality compression and low bandwidth solution aimed for point-to-point, as well as multipoint-tomultipoint scenarios over a single 100m Cat5e/6/7 cable. VEO-XTI1CG2 and VEO-XRI1CG2 are widely suitable for various applications which also require PoE, audio management, video wall compositing or remote control, such as educational, commercial, or corporate installations, where flexible and scalable AV systems are in need. Furthermore, this transmitter and receiver can be paired with VEO-XCTRLG2 control module for and expanded management experience with in-built WEB configuration interface.
3.1 MAIN FEATURES · HDMI 1.4 with video resolution up to 1920x1200p@60Hz 4:4:4. · Signal transmission distance up to 100m over Cat5e/6/7 cable. · Support for unicast over 1Gb unmanaged networks and multicast signal extension over 1Gb managed networks. · Support for video wall compositing up to 9 x 9 setups. · Support for audio embedding and extraction. · Support for mainstream and sub stream encoding modes. · Support for pass through and RS-232, TCP/IP, Web GUI management using VEOXCTRLG2 controller module. · HDCP 1.4 compliant. · Support for PoE function. · Local 12V DC power supply.
6

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

4. INSTALL & CONNECT
4.1 RACK MOUNTING IN VEO-RK1CG2 This product can be mounted in a VEO-RK1CG2 3U rack accessory (Please contact your supplier for rack sale). The mounting steps are as follows:
1. Use included screws to fix two mounting ears on the product, as shown in the figure below:
2. Insert the product with mounting ears into a 3U rack (up to 12 units can be installed vertically), as shown in the figure below:
3. Use screws to fix mounting ears on the rack to complete the mounting, as shown in the figure below:
7

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

4.2 NETWORK REQUIREMENTS AND CONFIGURATION VEO-XTI1CG2 and VEO-XRI1CG2 are not limited to certain brands of network hardware, but the network must support the following network features:
· Layer 3 managed network switch. · IGMP snooping support.
To prevent malfunctioning, interference or drop in signal performance due to other network products bandwidth requirements or network design. It is highly recommended to check with the chosen network IT staff how to properly set the Multicast products connected to the local network switch.
4.2.1 SETTING THE IP ADDRESS The default IP address is "auto IP" in the range 169.254.10.x for the transmitters and 169.254.20.x for the receivers. It can also be dynamically assigned by the VEO-XCTRLG2 controller in case it is present in the network. For further details please refer to VEOXCTRLG2 controller module user manual.
· It's possible to check the assigned IP address from a transmitter or receiver pressing and holding the (UP button) on the front panel. For further details, refer to Additional functionalities of CH select / buttons for both: VEO-XTI1CG2 & VEOXRI1CG2 chapter.
· The IP address can be changed using the embedded web page of a transmitter or a receiver. Both the network configuration of PC and VEO devices must be in the same network domain in order to be able to access its web settings page through an internet browser. For further details, refer to Configuration using Web interface chapter.
When static IP addresses are required, the IP address of each device needs to be set manually.
8

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

4.2.2 VIDEO DISTRIBUTION QUICK START
To begin a video transmission, a matching between a transmitter and a receiver is required. Each VEO-XTI1CG2 transmitter can stream a video signal over the network using an ID channel number that must be unique in the same network. Each ID channel from 0 to 762 identifies a IP address and every VEO-XRI1CG2 receiver can select one of these channels in order to receive an AV stream.
The ID channel for transmitters is usually set once during the setting up of the system while the receivers ID usually are the ones that are modified in order to show different content on the displays. The destination receiver ID must be set in the same channel as the transmitter broadcasting the desired source audio and video content.
The ID channel can be selected in four different ways: · By front panel buttons of the devices (VEO-XTI1CG2 has the ID assignement blocked by default and should be adjusted entering CFN mode, long pressing DOWN button. See chapter Additional functionalities of CH select / buttons for both: VEOXTI1CG2 AND VEO-XRI1CG2). "Button Fast Setting Local ID" can be enabled to unblock ID assignment for VEO-XTI1CG2 front buttons CH select regular operation. See chapter VEO-XTI1CG2 Settings for further details. · By using the Web Page configuration on the same device. · By using the Web Page configuration on VEO-XCTRLG2. · Via RS-232. · Via TCP using the VEO-XCTRLG2.
4.2.3 UNICAST MODE
When VEO-XTI1CG2 and VEO-XRI1CG2 devices are connected as a simple point to point extension, no additional configuration is needed.
1. Connect the source device to the VEO-XTI1CG2 transmitter to the HDMI port. 2. Connect Audio IN/OUT to a sound device and select the required audio mode. 3. Connect the remote endpoint to the VEO-XRI1CG2 receiver's HDMI port output. 4. Connect the transmitter and receiver with Cat5e/6/7 cable. 5. Connect an RS-232 cable from the automation system to the transmitter port. 6. Connect RS-232 cable from the receiver to the port of the device to control. 7. Power VEO-XTI1CG2 transmitter and VEO-XRI1CG2 receiver with the included
power adapter.
Set the same ID for both devices. 9

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

4.2.4 MULTICAST MODE When VEO-XTI1CG2 and VEO-XRI1CG2 devices are connected in a point to multipoint or multipoint to multipoint topology, every transmitter and receiver should have a unique IP address. When possible, it is recommended to create an independent IP video network using managed network switches. Use of gigabit switches with an IGMP support will create the most appropriate scenario.
1. Set the IP address for each transmitter and receiver. 2. Connect the source devices to the HDMI ports of the VEO-XTI1CG2 transmitters. 3. Connect the HDMI endpoints to the HDMI ports of the VEO-XRI1CG2 receivers. 4. Connect Audio IN/OUT to a sound device and select the required audio mode. 5. Connect an RS-232 cable from the automation system to the transmitters ports. 6. Connect RS-232 cables from the receivers to the ports of the devices to control. 7. Connect all VEO devices to the network switch using Cat. 5e/6/7cables. 8. Power VEO-XTI1CG2 transmitter and VEO-XRI1CG2 receiver with the included
power adapter and power the switch. In case the switch supports PoE (Power over Ethernet), it will not be necessary to power the VEO devices locally. 9. Choose the desired ID channel for each of the VEO devices in order to establish the required video transmission flows.
10

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

5. START-UP and OPERATION
5.1 CONFIGURATION USING WEB INTERFACE
VEO-XTI1CG2 and VEO-XRI1CG2 devices can be configured through their own built-in web interface by simply typing the IP address of the chosen device into a web browser. Refer to chapter Setting the IP address for further details on how to find the IP address of a VEO-XTI1CG2 and VEO-XRI1CG2. The default credentials to log in are:

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

· User name: · Password:

admin admin

Once the login credentials have been filled out correctly, the menus of the web settings page will let the user manage and operate different aspects and functionalities concerning transmitter and receiver operation, as explained in the next chapters.
5.1.1 INFORMATION

PANEL

FUNCTIONS

TECHNICAL

DATA

The Status page provides basic information about VEO-XTI1CG2 and VEO-XRI1CG2 such as:
· Firmware Version · IP Address · Subnet Mask · Gateway · MAC Address
11

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

5.1.2 VIDEO SETTINGS 5.1.2.1 VEO-XTI1CG2 VIDEO SETTINGS The video settings page will enable the user to configure the following parameters for VEO-XTI1CG2.
1. Main Stream · Video Encoding Format: the user can select H.265 and H.264 video codec for the mainstream. · Audio Encoding Format: the user can select PCM or AAC audio for the mainstream. · Resolution: it shows the HORITZONAL and VERTICAL resolution for the mainstream. This setting follows the input resolution of the video source. · Bitrate: the user can adjust the video quality choosing the maximum transmitted data for the mainstream.
2. Sub Stream · Video Encoding Format: the user can select H.265 and H.264 video codec for the sub stream. · Resolution: the user can set the HORITZONAL and VERTICAL resolution for the sub stream. · Bitrate: the user can adjust the video quality choosing the maximum transmitted data for the sub stream.
12

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

3. Audio Selection This parameter lets the user choose the Audio mode (ANALOGUE / HDMI) for the VEOXTI1CG2 transmitter's AUDIO IN. · ANALOGUE: audio signal coming from the external analogue source connected to AUDIO IN is embedded in the HDMI signal flow and outputted through AUDIO OUT connector in VEO-XRI1CG2. · HDMI: embedded audio in the HDMI signal flow is outputted through AUDIO OUT connector both in VEO-XTI1CG2 and VEO-XRI1CG2 connectors.

4. EDID Setting
This parameter selects the EDID setting for the VEO-XTI1CG2 transmitter. For further details, refer to Additional functionalities of CH select / buttons for both: VEOXTI1CG2 & VEO-XRI1CG2 chapter to check the available options.

EDID ID

EDID Description

Video: HDMI 1080p@60Hz / Audio: Stereo PCM

Video: HDMI 720p@60Hz / Audio: Stereo PCM

Video: DVI 1024p@60Hz

Video: DVI 1080p@60Hz

Video: DVI 1200p@60Hz

Video: HDMI 1200p@60Hz / Audio: Stereo PCM

Copy from VEO-XRI1CG2 HDMI output

USER 1

USER 2

User EDID 1 and User EDID 2 can be uploaded in SELECT USER EDID 1 FILE and SELECT USER EDID2 FILE. (This file can be downloaded from the Download EDID of the Receiver Video page).

INSTALL &
CONNECT

START-UP &
OPERATION

PANEL

FUNCTIONS

TECHNICAL

DATA

5.1.2.2 VEO-XRI1CG2: VIDEO SETTINGS
The video settings page will enable the user to configure the following parameters for VEO-XRI1CG2.

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

PANEL

FUNCTIONS

TECHNICAL

DATA

1. Transmission

This parameter selects UNICAST or MULTICAST as the chosen network transmission protocol.

2. Scaler Setting

This parameter sets the output resolution scaling up on the HDMI OUT of the VEOXRI1CG2 receiver.

Resolution ID 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19

Resolution Description Pass-through 1080p@60Hz 1080p@50Hz 1080p@30Hz 1080p@25Hz 1080p@24Hz 720p@60Hz 720p@50Hz 576@50Hz 480@60Hz 640x480@60Hz 800x600@60Hz 1024x768@60Hz 1280x800@60Hz 1280x1024@60Hz 1366x768@60Hz 1440x900@60Hz 1600x1200@60Hz 1680x1050@60Hz 1920x1200@60Hz

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

3. Download EDID This parameter enables the user to download the EDID binary file of the endpoint device connected to the VEO-XRI1CG2 receiver. The EDID file can be used as the User EDID file to be uploaded to the VEO-XTI1CG2.
4. Video Timeout Setting This parameter sets the timeout time to turn off the HDMI OUT output when no video signal is detected. Selecting "0" disables this function.
5. OSD Color Setting This section lets the user adjust the colour parameter of the data shown in the screen.
6. Picture Setting This section lets the user adjust video parameters (Brightness, Contrast, Hue and Saturation) to better fit the output display and deliver the most appropriate video experience possible.
15

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

5.1.3 LED This page allows the user to select the led status for both, VEO-XTI1CG2 and VEOXRI1CG2.
1. Front Panel Power LED Flash: This parameter selects the status of the Front Panel LED as follows: · ON: The LED remains permanently lighted. · OFF: After 90s the LED is switched off automatically.
2. Power LED Flashing: · ON: The Power LED remains permanently blinking. · OFF: The Power LED stays on without blinking. · ON 90s: The Power LED blinks for 90s and then stops.
16

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

5.1.4 SETTINGS 5.1.4.1 VEO-XTI1CG2 SETTINGS This page allows the user to modify the network configuration of the VEO-XTI1CG2 device.
1. Network · IP address · Subnet Mask · Gateway · HTTP Web Port · The Network Settings can be set only when the MODE button is set to Static. · After any changes to the network settings, username or password, the user will have to log in the Web GUI again with the new settings to resume working.
2. Security This parameter turns on or off HTTPS security protocol.
3. Setting Local ID: this parameter sets the ID Channel for the VEO-XTI1CG2 transmitter from the 1-762 available profiles. 17

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

4. Button Fast Setting Local ID Fast Setting: ON/OFF - This parameter enables the front buttons of the device so that the user can physically change the ID from the front panel of the device.
5. Username This parameter lets the user modify the username assigned to the device.
6. Login This section allows the user to change the current password to access the web settings page.
5.1.4.2 VEO-XRI1CG2 SETTINGS This page allows the user to modify the network configuration of the VEO-XRI1CG2device.
1. Network · IP address · Subnet Mask · Gateway · HTTP Web Port · The Network Settings can be set only when the MODE button is set to Static. · After any changes to the network settings, username or password, the user will have to log in the Web GUI again with the new settings to resume working. 18

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

2. Security This parameter turns on or off HTTPS security protocol.
3. Setting · Local ID: this parameter sets the ID Channel for the VEO-XRI1CG2 receiver from the 0-762 available profiles. · Max Channel ID: this parameter sets the range of ID Channel that will be available in the VEO-XRI1CG2 devices included in a given installation. Selecting "0" will enable the complete range of 0-762 channels. · Source Selection ID: this parameter sets the transmission channel for the VEOXRI1CG2 receiver from the 0-762 available channels. When both a transmitter and a receiver are tuned in the same channel, video will show from the VEOXRI1CG2 HDMI output.
4. Username This parameter lets the user modify the username assigned to the device.
5. Login This section allows the user to change the current password to access the web settings page.
5.1.5 UPDATE 5.1.5.1 VEO-XTI1CG2 UPDATE
1. Firmware Update: · Browse: This will import the upgrade file. · Update: This will start the upgrade process. When the progress bar reaches 100%, the upgrade is successful, and the device will restart.
2. Factory Reset: This will reset the device to the factory default settings. 3. Reboot: This will reboot the device.
19

PANEL

FUNCTIONS

TECHNICAL

DATA

5.1.5.2 VEO-XRI1CG2 UPDATE

PRECAUTIONS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

PACKAGE CONTENTS

PANEL

FUNCTIONS

1. Firmware Update: · Browse: This will import the upgrade file. · Update: This will start the upgrade process. When the progress bar reaches 100%, the upgrade is successful, and the device will restart.
2. IMG Update: · Browse: This will import the splash screen file. · Update: This will start the update the splash screen image that will show on the receiver when the input source is disconnected.
3. Factory Reset: This will reset the device to the factory default settings. 4. Reboot: This will reboot the device.

5.1.6 LOG OUT
Selecting Log Out automatically.

will exit the Web GUI and skip to the login interface

5.2 REMOTE CONTROLLING

5.2.1 RS-232
To match the ID from a transmitter to a receiver, connect the RS-232 port of VEO-XTI1CG2 and VEO-XRI1CG2 to a PC serial interface or a RS-232 control system or use VEOXCTRLG2 optional controller module.

5.2.1.1 RS-232 COMMUNICATION PROTOCOL

The serial parameters for a correct transmission are: Baud rate 115200 Data bits 8 Stop bits 1 Parity None

Flow control None

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

5.2.1.2 COMMAND LIST
It is important to add carriage return (<CR>,\r,0x0D) and line feed (<LF>,\n,0x0A) characters at the end of each command:
How do you have to enter the command? To launch a remote control command, it needs to be written as follows: "<Command> [Param 1] <Variable> [Param 2]" [Param 1], [Param 2] will not always be required for every command.
EXAMPLE OF USE: "SET DEC 1 SWITCH ENC 2\r\n" will assign Source Local ID of VEO-XRI1CG2 with Local ID 1 to the same as VEO-XTICG2 Local ID.

Command SET ENC [enc] (1)
or SET DEC [dec](2)
SET ENC [enc](1)

Transmitter and Receiver Control

Variable

Description

ID [id] · id = [1..762]

Set the index ID of the transmitter or receiver.

EDID COPY [dec](2)

Set the transmitter EDID copy from receiver.

EDID DEFAULT [edid]

Set the transmitter Default EDID.

· edid =

00: HDMI 1080p@60Hz, Audio 2CH PCM

01: HDMI 720p@60Hz, Audio 2CH PCM

02: DVI 1280x1024@60Hz, Audio None

03: DVI 1920x1080@60Hz, Audio None

04: DVI 1920x1200@60Hz, Audio None

05: HDMI 1920x1200p@60Hz, Audio 2CH PCM

06: Copy EDID

07: User EDID 1

08: User EDID 2

SET DEC [dec](2)

ALL

SWITCH ENC [enc](1)

Set the receiver switch all signals. Note: enc=0 mean no source in this case

START-UP &
OPERATION

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

SET DEC [dec](2) GET MAC\r

OUTPUT RESOLUTION [res] · res =

Set the receiver output resolution.

[0:Bypass 1:1080p@60 2:1080p@50
3:1080p@30 4:1080p@25 5:1080p@24 6:720@p60 7:720p@50 8:576p@50 9:480p@60 10:640x480@60 11:800x600@60 12:1024x768@60 13:1280x800@60 14:1280x1024@60 15:1366x768@60 16:1440x900@60 17:1600x1200@60 18:1680x1050@60 19:1920x1200@60]

PERMISSION [enc]\r :

Set the maximum transmitter ID number for the receiver to switch signals through buttons.

Get MAC of the transmitter/receiver.

(1)enc=000: All transmitter enc=[001...762]: One transmitter
(2)dec=000: All receiver dec=[001...762]: One receiver

· Any TX can control any TXs and RXs. The following api items 1 to 7 all can be used. · RX can only set parameters for the device connected to serial port, and only api 1
to 4 and the api 7 can be used.

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

5.2.2 ADVANCED NETWORK MANAGEMENT For larger AV over IP multicast scenarios involving several VEO-XTI1CG2 and VEOXRI1CG2 devices, it is recommended to add a VEO-XCTRLG2 controller module in the system. This unit will allow the user to manage and operate all the transmitters and receivers from a unique Web interface, including Preview mode, Matrix control, Video Wall management control or even the use of TCP commands to remotely communicate with VEOXTI1CG2 and VEO-XRI1CG2 units present in the network. For further details on how to set up an advanced networked installation control layout interface, please refer to VEOXCTRLG2 controller module user manual.
23

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

6. PANEL FUNCTIONS
6.1 VEO-XTI1CG2 (TX, TRANSMITTER) 6.1.1 FRONT PANEL
1. POWER LED: The LED flashes when the device is power supplied and stays lid (RED) after the start up is complete.
2. LINK LED: Network connection status LED: o Light on: Network connection is stable and there's a compatible video signal. o Light off: No network connection. o Light flashing (slow): Network connection is stable but there's no video signal. o Light flashing (fast): Network connection is stable but there's no compatible video signal (resolution or frame rate are greater than native).
3. STATUS DISPLAY: indicates current ID channel and further device information. When clicking the "SHOW ME" option on the VEO-XCTRLG2, the status display will flash "SHO" for an easier location of the corresponding device. For further details, refer to Additional functionalities of CH select / buttons for both: VEO-XTI1CG2 & VEO-XRI1CG2 chapter.
4. CH SELECT (UP/DOWN): Use these buttons to set the ID channel of the device. It is also possible to adjust audio mode, manage EDID, consult IP address, or enter configuration mode. For further details, refer to Additional functionalities of CH select / buttons for both: VEO-XTI1CG2 & VEO-XRI1CG2 chapter.
5. RESET: System reset button. Pressing and holding for 5 seconds will restart and restore factory settings on the device.
24

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

6.1.2 REAR PANEL
6. RS-232: Serial port for remote control. Signal pass-through supported. 7. AUDIO IN/OUT:
o AUDIO IN: When this mode is selected, the audio port acts as an input (audio embedding to HDMI).
o AUDIO OUT: When this mode is selected, the audio port acts as an output (audio extraction from HDMI).
8. LAN (PoE) CONNECTOR: Connect the 1Gb network port to an Ethernet switch to begin data transmission. When PoE on the Ethernet switch is available, the device will not need to be locally powered.
9. LINK indication (Green): o Light ON: The network cable is correctly connected. o Light OFF: No Network connection.
10. DATA Indicator (Yellow): o Flashing: Data transmission o Light OFF: No Data transmission
11. HDMI IN: HDMI input port 12. DC 12V PORT: Connect this port to the 12VDC included power supply.
25

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

6.2 VEO-XRI1CG2 (RX, RECEIVER) 6.2.1 FRONT PANEL
1. POWER LED: The LED flashes when the device is power supplied and stays lid (RED) after the start up is complete.
2. LINK LED: Network connection status LED: o Light on: Network connection is stable and there's a compatible video signal. o Light off: No network connection. o Light flashing (slow): Network connection is stable but there's no video signal. o Light flashing (fast): Network connection is stable but there's no compatible video signal (resolution or frame rate are greater than native).
3. STATUS DISPLAY: indicates current ID channel and further device information. When clicking the "SHOW ME" option on the XCTRLG2, the status display will flash "SHO" for an easier location of the corresponding device. For further details, refer to Additional functionalities of CH select / buttons for both: VEO-XTI1CG2 & VEOXRI1CG2 chapter.
4. CH SELECT (UP/DOWN): Use these buttons to set the ID channel of the device. It is also possible to adjust audio mode, manage EDID, consult IP address, or enter configuration mode. For further details, refer to Additional functionalities of CH select / buttons for both: VEO-XTI1CG2 & VEO-XRI1CG2 chapter.
5. RESET: System reset button. Pressing and holding for 5 seconds will restart and restore factory settings on the device.
26

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

6.2.2 REAR PANEL
6. RS-232: Serial port for remote control. Signal pass-through supported. 7. AUDIO OUT: The audio port acts as an audio de-embedder from HDMI. 8. LAN (PoE) CONNECTOR: Connect the 1Gb network port to an Ethernet switch to
begin data transmission. When PoE on the Ethernet switch is available, the device will not need to be locally powered. 9. LINK indication (Green):
o Light ON: The network cable is correctly connected. o Light OFF: No Network connection. 10. DATA Indicator (Yellow): o Flashing: Data transmission. o Light OFF: No Data transmission. 11. HDMI OUT: HDMI output port. 12. DC 12V PORT: Connect this port to the 12VDC included power supply.
27

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

6.3 ADDITIONAL FUNCTIONALITIES OF CH SELECT / BUTTONS FOR BOTH: VEOXTI1CG2 AND VEO-XRI1CG2

Settings IP Address
ID

Buttons Pressed

Description

Pressing and holding the button for 5 seconds will show the

current IP address of VEO-XTI1CG2 or VEO-XRI1CG2 device in

the Status display. This message will appear following the

sequence "xxx", "xxx", "xxx", "xxx".

Pressing and holding the button for 5 seconds will show the

current IDs of VEO-XTI1CG2 or VEO-XRI1CG2 device in the

Status display. This message will appear following the sequence

"xxx",

Wake up

After the system is powered on, the VEO-XTI1CG2 / VEOXRI1G2 device Status display will show the ID Channel. When idle and Display configured as OFF, pressing or button will turn on the Status display and show the current ID Channel number (e.g. 001).

Configuration

Pressing and holding and buttons together at the same time for 5 seconds will enter the "Configuration" mode with "CFN" displaying on the status display. Further long pressing of and buttons buttons will allow to confirm and enter in the next configuration menu.
and Available menus are:
· ID modifying. · EDID settings. · Audio Settings. · Output Resolution Settings (Only VEO-XRI1CG2). · Video Timeout Settings (Only VEO-XRI1CG2).

ID Settings

For VEO-XRI1C2G receivers the ID can be changed just pressing the or buttons and this allows to receive the desired streaming from the transmitter. VEO-XTI1CG2 Transmitter ID must be unique in a network so the procedure to change the ID is not so immediate.

and

Pressing and holding and buttons both together at the same time for 5 seconds will enter the "ID Settings" mode. The ID Channel will flash, then pressing the or button will select the desired ID Channel and pressing and hold and buttons once again both together at the same time for 5 seconds, will confirm the selected ID Channel and exit "ID Settings" mode and go to the next menu.

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

After showing ID settings menu, long pressing the or button until the Status display shows "E00" (in which "E" refers to EDID, "00" to EDID ID) in the Status display. Then pressing and holding and buttons both together at the same time buttons for 5 seconds will enter "EDID Settings" mode. The EDID ID number (e.g. E01) on the Status display will flash. Then pressing the or button will select the desired EDID ID:

EDID Settings (only VEO-XTI1CG2)

and

EDID ID
00 01 02 03 04 05 06 07 08

EDID Description
Video: HDMI 1080p@60Hz / Audio: Stereo PCM Video: HDMI 720p@60Hz / Audio: Stereo PCM Video: DVI 1024p@60Hz Video: DVI 1080p@60Hz Video: DVI 1200p@60Hz Video: HDMI 1200p@60Hz / Audio: Stereo PCM Copy from VEO-XRI1CG2 HDMI output USER 1 USER 2

· The default EDID of 1080p60 will be used if an EDID has not previously been copied to ID 06 or downloaded to ID 07/08 on VEO-XCTRLG2 Web GUI
· EDID ID 06/07/08 are not available without VEOXCTRLG2.

Pressing and holding and buttons both together for 5 seconds will confirm the selected EDID ID and exit "EDID Settings" mode.

Audio Settings (only VEO-XTI1CG2)

and

After showing EDID menu, long pressing or button until the Status display shows "AHE". Then pressing and holding and buttons both together for 5 seconds will enter the "Audio Settings" mode. The current audio mode will appear flashing. Pressing or button will select the desired option:
· AHE: HDMI embedded audio signal will be outputted through AUDIO OUT ports on VEO-XTI1CG2 and VEOXRI1CG2
· AEI: External audio source signal coming in AUDIO IN on VEO-XTI1CG2 will be outputted through AUDIO OUT port on VEO-XRI1CG2.

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

Long pressing the or button until the Status display shows "S00" (in which "S" refers to Scaler and "00" to resolution ID). Then pressing and holding and buttons both together for 5 seconds, will enter the "Output Resolution Settings" mode. The Resolution ID number (e.g. S01) on the Status display will flash. Then pressing the or button will select the desired resolution ID:

Output Resolution

Settings

and

(Only VEO-XRI1CG2)

Resolution ID 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19

Pressing and holding and buttons both together for 5 seconds will confirm the selected Resolution ID and exit "Output Resolution Settings" mode

Video Timeout

Settings

and

(Only VEO-XRI1CG2)

Long pressing the or button until the Status display shows "H00" (in which "H" refers to HDMI TIMEOUT an "00" to the time in minutes. Then pressing and holding and buttons both together for 5 seconds, will enter the "Video Timeout Setting" mode. The number (e.g., H01) on the Status display will flash. Press the or button to select the desired time to disable the HDMI output after the VEOXTI1CG2 HDMI input doesn't detect video signal.

PANEL

FUNCTIONS

TECHNICAL

DATA

7. TECHNICAL DATA

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

PRECAUTIONS

PACKAGE CONTENTS

7.1 TECHNICAL SPECIFICATIONS

VEO-XTI1CG2 / VEO-XRI1CG2

Video Performances Video Input Connector
Video Output connector Video Input Resolution
Video Output Resolution Video Codec
Transmission Latency
Chroma Subsampling Colour Depth Colour Space HDCP HDR
Video Composing Capabilities Scaling Feature HDMI Distance
Audio Performances Audio Input Connectors
Audio Output Connectors Audio Formats Sample Rate Bit Depth
Frequency Response ARC/eARC
Control Control Connectors Control Protocols Control Buttons
EDID Management Status Indicators
Pass-through Control Pass-through Connectors Pass-through Protocols
Network Network Connectors
Network Requirements Average Streaming Bitrate
Transmission Distance Electrical
Power Supply AC Mains Connector DC Mains Connector Power Consumption

Transmitter: HDMI Type A Female, 1.4, 10.2 Gbps Receiver: HDMI Type A Female, 1.4, 10.2 Gbps Up to 1920x1200 60Hz Up to 1920x1200 60Hz H.265 and H.264 <100ms compression depending on video content and transmission / network configuration RGB4:4:4, YCbCr 4:4:4, YCbCr 4:2:2 8-bit, 10-bit, 12-bit, 16-bit (1080p@60Hz) RGB, YCbCr 1.4 Not supported Videowall up to 9x9 Supported 15m with Ecler VEO Cables
Transmitter: 3-pin Euroblock (Stereo Unbalanced) Receiver and Transmitter: 3-pin Euroblock (Stereo Unbalanced) LPCM 2.0CH 32/44.1/48KHz Up to 24-bit 20Hz-20KHz Not Supported
RJ-45, Euroblock Web, TCP (only with VEO-XCTRLG2), RS-232 1 x UP button 1 x DOWN button Via front panel and Web settings POWER LED: Red; LINK LED: Green; LCD display
Euroblock RS-232
RJ-45 IGMP Snooping Configurable via software 1- 20Mbps 100m (Ethernet Standard)
PoE (802.3af Class 3) or External Power supply 100-240VAC 50-60Hz with EU, UK, US, AU blades 12VDC-1A with coaxial DC connector Transmitter: 3W / Receiver: 3W

PANEL

FUNCTIONS

TECHNICAL

DATA

PRECAUTIONS

Physical Operating Temperature
Operating Humidity Installation Options Included Accessories
Optional Accessories Dimensions (WxHxD)
Shipping Dimensions (WxHxD)
Weight Shipping Weight Chassis Material
Finished Colour

Min. -10°C - 14°F; Max. 45°C - 113°F <90% HR Desktop, 19" racks (1/2RU), VEO-RK1CG2 2x 3pins Euroblock connector 4x M3 screws 4mm 2x Mounting Ears 1x 12V PSU VEO-XCTRLG2, VEO-RK1CG2 95 x 21.5 x 120mm / 3.74 x 0.85 x 4.72in. (each one, TX and RX separately) 188 x 75 x 137 mm / 7.40 x 2.95 x 5.39 in. (each one, TX and RX separately) 0.3 Kg / 0,66 lb (each one, TX and RX separately) 0.7 Kg (each one, TX and RX separately) Metal Black

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

PANEL

FUNCTIONS

TECHNICAL

DATA

7.2 MECHANICAL DIAGRAM 7.2.1 VEO-XTI1CG2 7.2.2 VEO-XRI1CG2
3 3

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

PANEL

TECHNICAL

FUNCTIONS

DATA

PRECAUTIONS

PACKAGE CONTENTS

DESCRIPTION &
FEATURES

INSTALL &
CONNECT

START-UP &
OPERATION

PANEL

FUNCTIONS

TECHNICAL

DATA

All product characteristics are subject to variation due to production tolerances. NEEC AUDIO BARCELONA S.L. reserves the right to make changes or improvements in the design or manufacturing that may affect these product specifications.

For technical queries contact your supplier, distributor or complete the contact form on our website, in Support / Technical requests.

Motors, 166-168 -08038 Barcelona - Spain-(+34) 932238403 | information@ecler.com | www.ecler.com

References

Enriqueta Arboli Adobe PDF Library 24.2.23