ARM Single Board Computer IoT Edge Computing Solutions | Mixtile
User Manual for MIXTILE models including: Blade 3, Single Board Computer, Blade 3 Single Board Computer, Board Computer, Computer
Mixtile Blade 3 | Mixtile
Blade 3 | Single Board Computer User Manual Get Started with https://www.mixtile.com/wiki/
File Info : application/pdf, 17 Pages, 2.28MB
DocumentDocumentBlade 3 | Single Board Computer User Manual Get Started with https://www.mixtile.com/wiki/ Blade 3 User Manual Changes Version 1.0 Date 2022-06-15 Changes First version MIXTILE Name VT V1.0 Copyright © 2022 MIXTILE. - 2 - Blade 3 User Manual Index of Contents MIXTILE CHANGES ............................................................................................................................................................................................ - 2 - 1 INTRODUCTION ...................................................................................................................................................................... - 4 - 1.1 PRODUCT DESCRIPTION ............................................................................................................................................................................ - 4 1.2 PACKAGE LIST............................................................................................................................................................................................. - 4 1.3 MAIN FEATURES......................................................................................................................................................................................... - 4 1.4 BLOCK DIAGRAM & PRODUCT OVERVIEW................................................................................................................................................ - 5 - 1.4.1 Block Diagram.............................................................................................................................................................................- 5 1.4.2 Product Overview ......................................................................................................................................................................- 6 1.4.3 Physical Dimensions..................................................................................................................................................................- 7 1.5 KEY COMPONENT SPECIFICATIONS .......................................................................................................................................................... - 8 1.5.1 MIXTILE Core 3588....................................................................................................................................................................- 8 1.5.2 MicroSD Socket ..........................................................................................................................................................................- 8 1.5.3 Mini-PCIe Socket .......................................................................................................................................................................- 8 1.5.4 Gigabit Ethernet .........................................................................................................................................................................- 8 1.5.5 Power Input .................................................................................................................................................................................- 9 1.5.6 USB 2.0/3.0 Host Ports.............................................................................................................................................................- 9 1.5.7 Display Support..........................................................................................................................................................................- 9 1.5.8 U.2 Connector.............................................................................................................................................................................- 9 1.5.9 LEDs and Dip Switch .............................................................................................................................................................. - 10 - 2 CONNECTORS & PIN ASSIGNMENTS ..............................................................................................................................- 11 - 2.1 30-PIN CONNECTOR ..............................................................................................................................................................................- 11 2.2 FAN CONNECTOR ....................................................................................................................................................................................- 12 2.3 MINI-PCIE...............................................................................................................................................................................................- 12 2.4 MIPI-CSI.................................................................................................................................................................................................- 13 2.5 U.2 ...........................................................................................................................................................................................................- 14 2.6 DEBUG ......................................................................................................................................................................................................- 16 - 3 SPECIFICATIONS....................................................................................................................................................................- 16 - 3.1 ENVIRONMENTAL.....................................................................................................................................................................................- 16 3.2 MECHANICAL ...........................................................................................................................................................................................- 16 - 4 SUPPORT .................................................................................................................................................................................- 17 - 4.1 TECHNICAL SUPPORT ..............................................................................................................................................................................- 17 - V1.0 Copyright © 2022 MIXTILE. - 3 - Blade 3 User Manual 1 Introduction MIXTILE 1.1 Product Description The Mixtile Blade 3 is a low-cost, low-power SBC based on the next-generation Rockchip RK3588 CPU. It allows you to cluster numerous Mixtile Blade 3 SBCs to expand your deployment, making it ideal for quick development, AI application prototyping, and edge computing. Out-of-the-box, Mixtile Blade 3 is a stacking computer with an inbuilt PCIe Gen3 edge connector that enables the integration of many high-performance hardware platforms into a tiny form factor. That hardware, when combined, provides a network speed of up to 20 Gb/s and a memory bandwidth of up to 136 GB/s. A Mixtile Blade 3 cluster in a 19-inch 2U chassis can support up to 600 CPU cores and 1320 GHz of processing power while requiring less than 1500 W of power. 1.2 Package list l 1x Mixtile Blade 3 (heatsink installed) 1.3 Main Features l CPU: Rockchip Octa-core Cortex-A76/A55 SoC processor RK3588 l NPU: Up to 6 TOPS l Memory: Up to 32 GB LPDDR4 memory and up to 256 GB eMMC storage l HDMI interface: n HDMI 2.1 output (8K @ 60 FPS or 4K @ 120 FPS) n HDMI 2.0 input (4K @ 60 FPS) l Video encoder: H.264/H.265 video encoder up to 8K @ 30 FPS l Video decoder: H.265/H.264/VP9 video decoder up to 8K @ 60 FPS l Display: 4-lane MIPI-CSI l Storage expansion: n 4-lane PCIe Gen 3 in U.2 port n SATA 3.0 in U.2 port n Micro-SD 3.0 flash socket l PCIe expansion: Mini-PCIe socket with PCIe Gen 2.1 and USB 2.0 support l Ethernet expansion: Dual 2.5 gigabit Ethernet ports l USB: Dual USB 3.2 Gen 1 Type-C ports with DisplayPort 1.4 A l GPIOs: 30-pin GPIO socket that can be used as Digital I/O, I²C, USB 2.0, TTL UART, SPI, I²S l Software support: Preload customized Debian 11, also support other Linux distributions and Android 12 l Power: USB Type-C Port-1 Support USB PD 2.0 protocol (Optional: 12 V DC standard SATA power in via U.2 port) l Dimensions: 2.5-inch Pico-ITX form factor, 100 x 72 mm l Operating temperature: 0 to +80° C V1.0 Copyright © 2022 MIXTILE. - 4 - Blade 3 User Manual 1.4 Block diagram & Product overview MIXTILE 1.4.1 Block Diagram The Block diagram for the Blade 3 single-board computer is shown below with descriptions for each function. V1.0 Copyright © 2022 MIXTILE. - 5 - Blade 3 User Manual 1.4.2 Product Overview MIXTILE V1.0 Copyright © 2022 MIXTILE. - 6 - Blade 3 User Manual 1.4.3 Physical Dimensions MIXTILE V1.0 Copyright © 2022 MIXTILE. - 7 - Blade 3 User Manual MIXTILE 1.5 Key Component Specifications The key component specifications are described below with relevant hardware information and developing notices. For more information, pin assignments and signal descriptions are listed in Chapter 2, Connectors & Pin Assignments. 1.5.1 Rockchip 3588 The Rockchip RK3588 ARM64 CPU contains many peripherals to support multi-purpose. l Octa Cortex-A76/A55 SoC processing cores l Core operating frequencies up to 2.4GHz l Neural Process Unit with processing performance up to 6 TOPS l Support 8k@60 FPS H.265/H.264/VP9 decoder; 8K@30 FPS H.264/H.265 encoder l Supports up to 32 GB LPDDR4 memory and up to 256 GB eMMC storage The SDRAM is 32bits data width, 4 ranks LPDDR4 memory capacities from 4GBytes to 32GBytes. The system flash memory supports eMMC 5.1 memory capacities from 32GBytes to 256GBytes. The default memory setting is 4/16GBytes LPDDR4 and 32/128GBytes eMMC for Blade 3. 1.5.2 MicroSD Socket The MicroSD socket accepts standard 11mm x 15mm Micro-SD cards with capacities up to 256GBytes. The 4bits data interface supports the SDMMC3.0 protocol. While the default boot setting is the eMMC Flash which can change to the MicroSD card. 1.5.3 Mini-PCIe Socket The mini-PCIe is a PCI card interface with a small form factor that uses a standard 52-pin miniPCIe socket. It also contains a USB 2.0 interface. The mini-PCIe socket supports the module sizes of 3052. The module supporting configuration, including power, reset, and interrupt signals, is under software control by Core 3588. Since each module needs specific configuration definitions, check the configuration setting before connecting the module. USB Support The mini-PCIe socket supports a standard USB 2.0 interface. 1.5.4 Gigabit Ethernet The IEEE802.3 compliant Ethernet supports auto-negotiation of 10/100/1000/2500Mb half-duplex and full-duplex. The RGMII interface from the processor connects the 2.5GbE to an external PHY, RTL8125BG-CG. The RJ45 connector has some status and speed lights. The green light indicates V1.0 Copyright © 2022 MIXTILE. - 8 - Blade 3 User Manual MIXTILE that you are connected, and the flashing light indicates that data is being sent. The yellow light indicates 2500Mbps and is turned off for 10/100/1000Mbps. 1.5.5 Power Input Power Delivery (PD) The power port is a USB-C port that supports USB Power Delivery 2.0. A Power Delivery controller on-board allows for a maximum power input of 20V @ 3A. 12V DC DC power inputs from a DC SATA power via U.2 port require 12V @ 3A. 1.5.6 USB 2.0/3.0 Host Ports The Blade 3 features two USB Type-C ports. Both ports can support the USB-OTG capability as well as DisplayPort via USB Type-C. DisplayPort over USB Type-C enables the USB Type-C connector and cable to offer audio/video (AV) transfer via the DisplayPort interface. It supports DisplayPort 1.4 and has a maximum resolution of 7680x4320@30Hz. USB Type-C Port-1 supports USB PD2.0 but not USB 2.0 for ADB. Although USB Type-C Port-0 does not support USB PD2.0, it does support USB 2.0 for ADB debugging and firmware updates. 1.5.7 Display Support The video output processor supports the resolution from 1920x1080@60Hz to 7680x4320@60Hz. The default main display is HDMI. HDMI-OUT HDMI display compliant HDMI 1.4 and HDMI 2.1 with HDCP 2.3. It supports up to 1920x1080@120Hz and 7680x4320@60Hz/3840x2160@120Hz resolution. HDMI-IN HDMI input compliant HDMI 1.4 and HDMI 2.0 with HDCP 2.3. It supports input source up to 1920x1080@120Hz and 3840x2160@60Hz resolution. 1.5.8 U.2 Connector The U.2 interface employs a 68-pin U.2 connector with a standard SATA 3.0 signal, a PCIe 3.0 X4 signal (four lanes PCIe 3.0), and 12V power input. V1.0 Copyright © 2022 MIXTILE. - 9 - Blade 3 User Manual 1.5.9 LEDs and Dip Switch MIXTILE The power LED indicate the status of the power supply. There is one SPST four-position dip switch that can be used to determine the system booting mode of the Blade 3 board. Only one position can be turned to ON at a time; please keep in mind that you cannot switch two positions to ON at the same time. When position 1 is set to ON, the Blade 3 will boot from eMMC. When position 2 is set to ON, the Blade 3 will boot from the MicroSD card. When position 3 is turned ON, the Blade 3 will boot from SPI Flash. When position 4 is activated, Blade 3 enters MaskROM mode for firmware development. V1.0 Copyright © 2022 MIXTILE. - 10 - Blade 3 User Manual 2 Connectors & Pin Assignments MIXTILE The following section lists the interfaces connector pin assignments, pin types with corresponding signal descriptions. The interface connectors on Blade 3 are listed in the table below. 2.1 30-Pin Connector Pin Pin Pin Input/ Signal Description # Name Type Output 1 VCC_5V0 Power Output Power supply for USB,5V output MAX 500mA. 2 GND Power NA Power and signal reference ground. 3 USB20_HOST0_DM LVDS BI USB20 HOST Port0 Data Minus 4 I2S2_SDI_M1 signal Input I2S2 data input 5 USB20_HOST0_DP LVDS BI USB20 HOST Port0 Data Plus 6 I2S2_SDO_M1 signal Output I2S2 data output 7 GND Power NA Power and signal reference ground. 8 I2S2_MCLK_M1 signal Output I2S2 Master clock 9 I2C5_SDA_M3 signal BI I2C5 Bus Date 10 I2S2_SCLK_M1 signal BI I2S2 serial clock or BCLK 11 I2C5_SCL_M3 signal Output I2C5 Bus clock 12 I2S2_LRCK_M1 signal BI I2S2 Left/Right channel clock 13 GND Power NA Power and signal reference ground. 14 GND Power NA Power and signal reference ground. 15 SPI4_MISO_M2 signal Input SPI4 Master input,Slave output 16 CAN2_RX signal Input CAN2 receive data 17 SPI4_MOSI_M2 signal Output SPI4 Master output, Slave input 18 CAN2_TX signal Output CAN2 transmit data 19 SPI4_CLK_M2 signal Output SPI4 clock 20 GND Power NA Power and signal reference ground. 21 SPI4_CS0_M2 signal Output SPI4 Chip Select 0 22 GPIO0_B0 signal BI GPIO bank 0 port B0 23 GPIO1_A4 signal BI GPIO bank 1 port A4 24 SARADC_VIN7 Analog Input SAR ADC Channel 7 input 25 GND Power NA Power and signal reference ground. 26 SARADC_VIN6 Analog Input SAR ADC Channel 6 input 27 PWM14 signal BI Pulse Width Modulation 14 input or output 28 GND Power NA Power and signal reference ground. 29 PWM15 signal BI Pulse Width Modulation 15 input or output 30 VCC_3V3_S0 Power Output Power supply for peripheral, 3.3V output MAX 500mA. V1.0 Copyright © 2022 MIXTILE. - 11 - Blade 3 User Manual 2.2 Fan Connector MIXTILE Pin Pin # Name 1 VCC5V_FAN 2 GND Pin Type Power Power Input/ Output Output NA Signal Description Power supply for FAN,5V output MAX 400mA.Control by GPIO3_C0 Power reference ground. 2.3 Mini-PCIe Pin Pin Pin Input/ Signal Description # Name Type Output 1 MINIPCIE20_WAKEN_3V3_L signal Input Wake up signal from mini-PCIe device 2 VCC3V3_MINIPCIE Power Output Power supply for mini-PCIe device,3.3V output MAX 3A in all pins 3 NC float NA No connected to this pin 4 GND Power NA Power and signal reference ground. 5 NC float NA No connected to this pin 6 NC float NA No connected to this pin 7 MINIPCIE20_CLKREQN_3V3_L signal Input PCIe2.0 Channel Reference clock request 8 NC float NA No connected to this pin 9 GND Power NA Power and signal reference ground. 10 NC float NA No connected to this pin 11 PCIE20_2_REFCLKN LVDS Output PCIe20 Port2 differential clock Negative 12 NC float NA No connected to this pin 13 PCIE20_2_REFCLKP LVDS Output PCIe20 Port2 differential clock Positive 14 NC float NA No connected to this pin 15 GND Power NA Power and signal reference ground. 16 NC float NA No connected to this pin 17 NC float NA No connected to this pin 18 GND Power NA Power and signal reference ground. 19 NC float NA No connected to this pin 20 W_DISABLEN signal Output PCIE device wireless disable 21 GND Power NA Power and signal reference ground. 22 MINIPCIE20_PERSTN signal Output PCIE device reset 23 PCIE20_2_RXN LVDS Input PCIe20 receive differential Negative 24 VCC3V3_MINIPCIE Power Output Power supply for mini-PCIe device,3.3V output MAX 3A in all pins 25 PCIE20_2_RXP LVDS Input PCIe20 receive differential Positive 26 GND Power NA Power and signal reference ground. 27 GND Power NA Power and signal reference ground. 28 NC float NA No connected to this pin V1.0 Copyright © 2022 MIXTILE. - 12 - Blade 3 User Manual 29 GND 30 NC 31 MINIPCIE20_TX_N 32 NC 33 MINIPCIE20_TX_P 34 GND 35 GND 36 MINIPCIE_USB_DM 37 GND 38 MINIPCIE_USB_DP 39 VCC3V3_MINIPCIE 40 GND 41 VCC3V3_MINIPCIE 42 NC 43 GND 44 NC 45 NC 46 NC 47 NC 48 NC 49 NC 50 GND 51 NC 52 VCC3V3_MINIPCIE 2.4 MIPI-CSI Pin Pin # Name 1 GND 2 MIPI_CSI0_RX_D0N 3 MIPI_CSI0_RX_D0P 4 GND 5 MIPI_CSI0_RX_D1N 6 MIPI_CSI0_RX_D1P 7 GND 8 MIPI_CSI0_RX_CLK0N V1.0 Power float LVDS float LVDS Power Power LVDS Power LVDS NA NA Output NA Output NA NA BI NA BI Power Output Power NA Power Output float NA Power NA float NA float NA float NA float NA float NA float NA Power NA float NA Power Output MIXTILE Power and signal reference ground. No connected to this pin PCIe20 transmit differential Negative No connected to this pin PCIe20 transmit differential Positive Power and signal reference ground. Power and signal reference ground. USB20 HOST Port1 Data Minus Power and signal reference ground. USB20 HOST Port1 Data Plus Power supply for mini-PCIe device,3.3V output MAX 3A in all pins Power and signal reference ground. Power supply for mini-PCIe device,3.3V output MAX 3A in all pins No connected to this pin Power and signal reference ground. No connected to this pin No connected to this pin No connected to this pin No connected to this pin No connected to this pin No connected to this pin Power and signal reference ground. No connected to this pin Power supply for mini-PCIe device,3.3V output MAX 3A in all pins Pin Type Power LVDS LVDS Power LVDS LVDS Power LVDS Input/ Output NA Input Input NA Input Input NA Input Signal Description Power and signal reference ground. MIPI CSI0 receive differential data lane 0 Negative MIPI CSI0 receive differential data lane 0 Positive Power and signal reference ground. MIPI CSI0 receive differential data lane 1 Negative MIPI CSI0 receive differential data lane 1 Positive Power and signal reference ground. MIPI CSI0 receive differential Clock 0 Negative Copyright © 2022 MIXTILE. - 13 - Blade 3 User Manual 9 MIPI_CSI0_RX_CLK0P 10 GND 11 MIPI_CSI0_RX_D2N LVDS Input Power NA LVDS Input 12 MIPI_CSI0_RX_D2P 13 GND 14 MIPI_CSI0_RX_D3N LVDS Input Power NA LVDS Input 15 MIPI_CSI0_RX_D3P LVDS Input 16 GND Power NA 17 MIPI_CAM_PWM2 signal Output 18 NC float NA 19 VCC_3V3_S0 Power Output 20 MIPI_CAM_RESETN signal Output 21 NC float NA 22 MIPI_CAM_PDN signal Output 23 I2C3_SDA_M3_MIPI signal BI 24 I2C3_SCL_M3_MIPI signal Output 25 GND Power NA 26 MIPI_CAM2_CLK_M1_3V3 signal Output 27 GND Power NA 28 VCC_5V0 Power Output 29 VCC_5V0 Power Output 30 VCC_5V0 Power Output MIXTILE MIPI CSI0 receive differential Clock 0 Positive Power and signal reference ground. MIPI CSI0 receive differential data lane 2 Negative MIPI CSI0 receive differential data lane 2 Positive Power and signal reference ground. MIPI CSI0 receive differential data lane 3 Negative MIPI CSI0 receive differential data lane 3 Positive Power and signal reference ground. PWM2 for LENS No connected to this pin Power supply for sensor board,3.3V output GPIO out for sensor reset No connected to this pin GPIO out for sensor power down I2C5 Bus data I2C5 Bus clock Power and signal reference ground. Camera Master clock output Power and signal reference ground. Power supply for sensor board,5V output Power supply for sensor board,5V output Power supply for sensor board,5V output 2.5 U.2 Pin Pin Pin Input/ Signal Description # Name Type Output E1 PCIE30_REFCLKP_SLOT LVDS Output RC PCIe30 differential clock Positive E2 PCIE30_REFCLKN_SLOT LVDS Output RC PCIe30 differential clock Negative E3 VCC_3V3_S0 Power Output Power supply for IO E4 PCIE30X4_CLKREQN_M1_L signal Output DM PCIe30 Channel Reference clock request E5 PCIE30X4_PERSTN_M1_L signal Input DM PCIe30 Channel reset E6 PCIE30X4_CLKREQN_M3 signal Input RC PCIe30 Channel Reference clock request E7 PCIE30_PORT1_REFCLKP LVDS Input DM PCIe30 differential clock Positive E8 PCIE30_PORT1_REFCLKN LVDS Input DM PCIe30 differential clock Negative E9 GND Power NA Power and signal reference ground. E10 PCIE30_PORT1_TX2P LVDS Output DM PCIe30 transmit differential Positive E11 PCIE30_PORT1_TX2N LVDS Output DM PCIe30 transmit differential Negative E12 GND Power NA Power and signal reference ground. V1.0 Copyright © 2022 MIXTILE. - 14 - Blade 3 User Manual E13 PCIE30_PORT1_RX2N E14 PCIE30_PORT1_RX2P E15 GND E16 NC E17 PCIE30_PORT0_RX1P E18 PCIE30_PORT0_RX1N E19 GND E20 PCIE30_PORT0_TX1N E21 PCIE30_PORT0_TX1P E22 GND E23 I2C4_SCL_M0 E24 I2C4_SDA_M0 E25 DUALPORT_EN# P1 PCIE30X4_WAKEN_M1_L P2 PCIE30X4_WAKEN_M3 P3 PWRDIS P4 IFDET P5 GND P6 GND P7 NC P8 NC P9 NC P10 PRSNT# P11 ACTIVITY# P12 GND P13 U2_12V P14 U2_12V P15 U2_12V S1 GND S2 SATA0_TXP S3 SATA0_TXN S4 GND S5 SATA0_RXN S6 SATA0_RXP S7 GND S8 GND S9 NC S10 NC S11 GND S12 NC S13 NC S14 GND S15 PCIE30X4_PERSTN_M3 LVDS LVDS Power float LVDS LVDS Power LVDS LVDS Power signal signal signal signal signal signal signal Power Power float float float signal signal Power Power Power Power Power LVDS LVDS Power LVDS LVDS Power Power float float Power float float Power signal Input Input NA NA Input Input NA Output Output NA Output BI Output Output Input Output Input NA NA NA NA NA Input Input NA Input Input Input NA Output Output NA Input Input NA NA NA NA NA NA NA NA Output MIXTILE DM PCIe30 receive differential Negative DM PCIe30 receive differential Positive Power and signal reference ground. No connected to this pin RC PCIe30 receive differential Negative RC PCIe30 receive differential Positive Power and signal reference ground. RC PCIe30 transmit differential Positive RC PCIe30 transmit differential Negative Power and signal reference ground. I2C4 Bus clock I2C4 Bus data GPIO for Enable dual port, default low DM PCIE30 Wake up signal from RC RC PCIE30 Wake up signal from DM GPIO for power disable to device GPIO for detect interface of device Power and signal reference ground. Power and signal reference ground. No connected to this pin No connected to this pin No connected to this pin GPIO for detect device if present GPIO for detect device if activity Power and signal reference ground. Power supply for blade3,input 12V Power supply for blade3,input 12V Power supply for blade3,input 12V Power and signal reference ground. SATA30 Port0 transmit differential Positive SATA30 Port0 transmit differential Negative Power and signal reference ground. SATA30 Port0 receive differential Positive SATA30 Port0 receive differential Negative Power and signal reference ground. Power and signal reference ground. No connected to this pin No connected to this pin Power and signal reference ground. No connected to this pin No connected to this pin Power and signal reference ground. RC PCIe30 Channel reset V1.0 Copyright © 2022 MIXTILE. - 15 - Blade 3 User Manual S16 GND S17 PCIE30_PORT1_TX3P S18 PCIE30_PORT1_TX3N S19 GND S20 PCIE30_PORT1_RX3N S21 PCIE30_PORT1_RX3P S22 GND S23 PCIE30_PORT0_RX0P S24 PCIE30_PORT0_RX0N S25 GND S26 PCIE30_PORT0_TX0N S27 PCIE30_PORT0_TX0P S28 GND Power LVDS LVDS Power LVDS LVDS Power LVDS LVDS Power LVDS LVDS Power NA Output Output NA Input Input NA Input Input NA Output Output NA MIXTILE Power and signal reference ground. DM PCIe30 transmit differential Negative DM PCIe30 transmit differential Positive Power and signal reference ground. DM PCIe30 receive differential Negative DM PCIe30 receive differential Positive Power and signal reference ground. RC PCIe30 receive differential Negative RC PCIe30 receive differential Positive Power and signal reference ground. RC PCIe30 transmit differential Negative RC PCIe30 transmit differential Positive Po+A137:E196wer and signal reference ground. 2.6 Debug Pin Pin Pin Input/ Signal Description # Name Type Output 1 UART2_RX_M0_DEBUG signal Input UART2 Receive Data for debug 2 UART2_TX_M0_DEBUG signal Output UART2 Transmit Data for debug 3 GND signal NA Signal reference ground. 3 Specifications 3.1 Environmental Parameter Operating Temperature Storage Temperature 3.2 Mechanical Parameter 2.5-inch Pico-ITX Weight Specifications 0 ° to +80 °C 0 ° to +80 °C Specifications 100 x 72mm 160g V1.0 Copyright © 2022 MIXTILE. - 16 - Blade 3 User Manual 4 Support MIXTILE 4.1 Technical Support MIXTILE technical support team assists you with the questions you may have. Contact us with the following methods below. Email: support@mixtile.com Website: https://www.mixtile.com V1.0 Copyright © 2022 MIXTILE. - 17 -