User Manual for Tonve models including: 716 MHz Cell Phone Signal Booster, 716 MHz, Cell Phone Signal Booster, Phone Signal Booster, Signal Booster, Booster
Cell Phone Signal Booster, Cell Phone Booster for Home Up to 6000 sq ft | Support All Carriers on Band 2/4/5/12/13/17 | Boost 5G 4G& LTE Signal for Verizon, AT&T, T-Mobile & More | FCC Approved : Cell Phones & Accessories
File Info : application/pdf, 8 Pages, 740.29KB
DocumentDocumentCell Phone Signal Booster User Manual Solve signal problems and improve quality of life Email: support@tecmad.com Whats app: CATALOG INTRODUCTION 1 WHAT IS INCLUDED FOR THE KIT 2 SPECIFICATIONS 3 HOW IT WORKS 4 LCD FEATURES 5 HOW TO INSTALL YOUR SIGNAL BOOSTER 6 INSTALLATION PREPARATION 7 INSTALL OUTDOOR ANTENNA 8 INSTALL INDOOR ANTENNA 9 INSTALL SIGNAL BOOSTER 10 FCC / IC STATEMENT 11 PRODUCT WARRANTY 12 INTRODUCTION This series booster is a newly designed signal boosters with intelligent functions, And it has been sold offline for a very long time and has won unanimous praise from customers. It can enhance indoor signal, such as voice, data in home and office etc, so as to reduce the problem of call interruption, poor signal, can help improve voice quality, faster internet speed and wider coverage. It also has an advanced set of technical features, will give you the ultimate control over your signal quality. With Good Looking and high quality LCD touch screen, Wireless connects multiple devices, Automatic gain control, this booster has strong anti-interference, low noise characteristic, it can cover up to 4000sq.ft coverage, Works on bands 12/13/5/ 2/4, Support all US and Canadian carriers of AT&T, Verizon, T-Mobile, Sprint, Straight Talk, U.S. Cellular, etc. Cover 2G, 3G, 4G LTE, and 5G compatible. The booster introduces the features from the consumer electronic device, which could support the operation via LCD touch screen in the front panel. Also it has many intelligent function, such as antenna isolation detection, input&output signal strength indication, central frequency display and setting, smart functions. See the Signal Booster Kit detailed introduction listed below: Boost er Out side ant enna Out side cable Indoor ant enna Accessories Email: support@tecmad.com Adapt er 01/ 02 Electrical specification Uplink Downlink Frequency Range (700+850+1900+ 1700/ 2100Mhz) LTE(A&B) LTEC CDMA PCS 698~ 716 MHz 776~ 787MHz 824~849 MHz 1850 ~ 1910 MHz 728 ~746 MHz 746 ~757 MHz 869~894MHz 1930 ~ 1990MHz AWS 1710~ 1755 MHz SYN- LCPAL10L- F 60dB 2110 ~ 2155 MHz 65dB Max .Gain SYN- LCPAL13L- F 65dB 65dB SYN- LCPAL17LF 65dB 70dB Max .Output Power 17dBm 17dBm Band width Wide Band Automatic Level Control MGC function Int ermod ulat ion Products 9KHz~1GHz 1GHz~12.75GHz 30dB 31dB/1dB step -19dBm -19dBm -19dBm -19dBm 9KHz~1GHz Spurious Emission 1GHz~12.75GHz -36dBm -30dBm Gain Flatness 8dB Noise Figure 6dB VSWR 2 Group Delay 1.0s Frequency stability 0.01ppm LED Alarm St and ard Power LED Power Indicator ALC LED Orange @ ALC 1~5dB, Red @ ALC15dB~20dB, Mechanical Specifications St and ard I /O Port N- Female Impedance 50 ohm Operating Temperature - 25ºC~+55ºC Environment Conditions IP40 Dimensions 240*140*35mm/9.5*5.5*1.4inch Weight 2.26kg/5.0Lbs Power Supply Input AC100~240V,output DC9V/3A Kit Including: Cell Phone Signal Booster*1 5G Indoor Panel Antenna with 32ft cable*1 Outdoor omnidirectional antenna*1 50ft Cable 4DB*1 HOW IT WORKS Base Station outside signal outside antenna outdoor calbe Working Principle b oost er indoor antenna with cable Out side Signal: Receive the signal from the outdoor base st at ion signal tower Out door Ant enna Gain: The gain of outdoor antenna Out door Cable Loss: The loss of t he outdoor cable Boost er Gain: The act ual working gain of t he booster Indoor Cable Loss: The loss of t he indoor cable Indoor Ant enna Gain: The gain of indoor antenna For example: - 65dBm + 6dBi - 5dB + 70dB - 3dB + 6dBi = 9dBm (System OutputPower) - 65dBm + 6dBi - 5dB + 70dB - 3dB + 6dBi = 9dBm (System Output Power) Tips:The user guide is focused on: 1. Getting the best outside signal. 2. Keeping the maximum booster gain. Email: support@tecmad.com 03/ 04 LCD FEATURES: HOW TO INSTALL YOUR SIGNAL BOOSTER This user manual will help you properly install your signal booster kit. lt is important to read through all of the installation steps before installing your equipment. Thoroughly read through the instructions, visualize where all the equipment will need to be installed and do a soft installation by placing the devices where they need to be before mounting any equipment. 1 signal intensit y 2 isolat ion condit ion: Green color: normal Orange: weak self-excitation Red :strict self-excitation. 3 work frequency band, this position can be touched to switch the frequency. 4 overpower alarm status display: Green: AGC normal Orange: AGC works in the range of 1-15dB overpower alarm Red: AGC works alarm overpower 15dB. 5 Outdoor output signal 6 the booster output signal strength. 7 downlink gain 8 Touch function(Smart Mode) 9 Press the inverted triangle to set up and decrease the gain 10 Press the triangle button to set up and increase the gain 11 uplink gain 12 the booster input signal strength. Note: The booster requires 1-2bars reliable signal outdoor, we recommend you to test your signals outdoor on your mobile phone before purchasing. Here are the effects of different signals for your reference. Email: support@tecmad.com 05/ 06 Installation Overview Installation Method 1: st ep 1 st ep 2 Step 1. Find the outside area with the strongest signal. Step 2. Install the outside antenna on the roof to obtain the strongest downlink signal from the local cellular towers. It should also be as far away as possible from where you plan to place the indoor antenna. Step 3. Install the indoor antennas where you want to improve the signal level. Step 4. Mount the boost; connect the cables from the outdoor antenna and indoor antenna at the designated ports, or place the Flare on a table or desktop, center of the area where signal is needed. Step 5. Connect the booster to an AC power source. (make sure all the cables are connected tightly before applying power) There are tools required before installation as follows FYI: Tools Required Phillips Screwdriver Drill 1.1 Install Outdoor Antenna Mobile Phone IMPORTANT: Testing the signal 3 times in the desired location before installing the outdoor antenna will help ensure the clearest and most stable signal for phone calls and data transmission. Using the hardware provided, mount the outside antenna as high as possible, allowing for a minimum25 feet from the planned location of the booster. The Omni Antenna receives and sends signals in a 360-degree radius. Mount the antenna at the highest possible elevation and in an uprightposition. This Supplied hardware allows for surface or pole mounting. Mount antenna to a vertical surface: 1. Find a position where could receive great signal,mostly a higher position, like at rooftop. 2. Place the antenna base and clip to the pole 3. The U-bolt passes through the pole clamp and the antenna and is inserted into the hole 4. Flat piece through screw 5. Reed t hrough screw 6. Thread t he nut t hrough t he screw and t ighten 7. Connect antenna to one end of the provided cable and tighten the connection. Run the cable along route to planned location of your booster. Email: support@tecmad.com 07/ 08 Installation Method 2: Tips: A.The Inside Panel Antenna should be facing the area signal is needed and away from the outdoor antenna B.Radiation shall be good enough to cover whole space C.Loop back shall be avoided st ep 1 st ep 2 st ep 3 After identifying the areas with the strongest signal, select the surface on which to mount the outside antenna. 1. Find a good location and drive the expansion pipe into the wall 2. Then align the antenna L-bracket with the expansion tube, screw in the screws and fix it 3. Connect antenna to one end of the provided cable and tighten the connection. Run the cable along route to planned location of your booster. 1.2 Install Indoor Antenna Select a place on a wall in the area where you need better reception. Mount the indoor antenna with the included screws as shown in the figure below. 1. Find the proper location for indoor antenna 2. Fix the indoor wall-mounted pinch plate to the wall with screws 3. Then install the support bracket on the back of the antenna directly on the buckle plate 4. And t hen connect t he booster st ep 1 Email: support@tecmad.com st ep 2 st ep 3 09/ 10 1.2 Install your signal booster Place the booster in a central location where signal is needed and at least 50ft. from the outdoor antenna location. And the signal booster should be mounted in an easily accessible area so it's easy to perform general maintenance. The optimal area would be on a wall located near a power outlet. Mount the booster with the included screws as shown in the figure below. The booster will be inst alled in t wo ways 1. Fix the four corners with screws and inst all it on t he wall 2. Hang it on the wall with the back buckle FCC Certification Power listed is conducted at antenna terminals. The antennas used with the signal booster must be installed to provide a separation distance of at least 20cm from all persons. Users and installers must be provided with the antenna kitting and installation and operating instructions and conditions for satisfying RF exposure and Section 20.21(a) compliance. This Wideband Consumer Signal Booster is authorized only for operation by and marketing to members of the general public for their personal use in accordance with the requirements of Sections 20.21(a)(7) and 20.21(g). This device is a Wideband Fixed Consumer Signal Booster approved for operating with the coverage/server antenna installed at a fixed location inside a building. The installation height of the antenna for AWS band (1700/2100 MHz) operations is limited to 10 meters above ground for compliance with Section 27.50. This equipment complies with FCC radiation exposure limits set forth for an uncont rolled environment . This equipment should be inst alled and operat ed wit h a minimum dist ance of 20cm bet ween t he radiat or and your body. This t ransmit t er must not be co- locat ed or operat ing in conjunct ion wit h any ot her ant enna or t ransmit t er. 3. Connect the cable of the indoor antenna to the port on the side of the booster silk-printed INDOOR 4. Route the cable from the outside antenna inside and connect it to the port on the booster silk-printed OUTDOOR 5. Connect the power adapter cord to the signal booster and plug into the power outlet. The LCD Screen will light and functioning properly No t e: 1. Do NOT connect the power adapter to the Signal Booster until you have connected both the Inside and Outside Antennas. 2. The booster case may become warm during operation, this is normal, please don't worry. PRODUCT WARRANTY 30-Day Money-Back: All boosters are protected by a 30-day money- back guarantee. If for any reason the performance of any product is not acceptable, the product may be returned to the reseller with a dated proof of purchase. 3-Year Warranty boosters and kits are warranted for 3 years. Products returned by customers must be in their original, un-modified condition, shipped in the original or protective packaging with proof-of-purchase documentation enclosed, and a Return Merchandise Authorization (RMA) number printed clearly on the outside of the shipping container. Email: support@tecmad.com 11/ 12Adobe PDF library 16.03 Adobe Illustrator 26.0 (Windows)