U.S. Environmental Protection Agency | US EPA
Indoor Architectural Lighting | Ledalite | Genlyte Solutions
Commercial Lighting Company | Genlyte Solutions | Signify
Installation Guide for LEDALITE models including: IS-DecoForm-Recessed, IS-DECOFORM-RECESSED, IS-DecoForm-Recessed Ledalite Signify Recessed LED, IS-DecoForm-Recessed, Ledalite Signify Recessed LED, Signify Recessed LED, Recessed LED, LED
21 апр. 2025 г. — These instructions review how to install recessed DecoForm fixtures. Please refer to layout drawings supplied by Ledalite in conjunction.
File Info : application/pdf, 11 Pages, 1.47MB
DocumentDocumentRecessed LED DecoForm IS-DECOFORM-RECESSED System Overview These instructions review how to install recessed DecoForm fixtures. Please refer to layout drawings supplied by Ledalite in conjunction with these installation instructions. The information below shows the available aesthetics and components required to install a standalone DecoForm or back-to-back in a pattern and in Chicago Plenum application along with top tile installation. IMPORTANT: Read all instructions including fixture/sensor wiring AND mechanical details before beginning installation. DecoForm Recessed i Optional 6' Flex Whip Drywall Trim Frame i Installation Sheet Optional snap-in 6' flex whip is prewired at the factory. · Compatible with NEMA Type G, NFG, NFSG, and SS Grid Ceilings Scan or click Link i Tools required - #2 Phillips or #2 Robertson screwdriver, needle nose pliers (optional) & metal snips (optional) ! ATTENTION: Install in accordance with local and national building and electrical codes. 4/21/2025 page 1 www.ledalite.com IS-DF Recessed Fixture Installation Sheet This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Warning! Shock Hazard! Warning! Shock Hazard! ! Installation IMPORTANT: Disconnect or turn off power before attempting any installation, service or maintenance. IMPORTANT: Fixture must be connected to building ground via the provided ground wire before reconnecting to mains power supply. Read all instructions including fixture/sensor wiring mechanical details before beginning installation. Beware of sharp edges on fixture. ! Handle With Care i Installation Notes i Installation Notes · Do not put pressure on the lens during installation. · Lift using both hands from the edges only. i Power Feed - Standalone Power feed The procedure for making electrical connections in an emergency driver box is the same as the driver box. Arrange boxed fixtures on floor in specified mounting locations, based on supplied layout drawings. Remove fixtures from boxes. i Power Feed - Continuous Row Power feed Driver Driver Driver · Every fixture contains its own driver & receives a direct power feed. Driver Driver Driver · Every fixture contains its own driver and power is daisy chained to each fixture (by others). See Step 7 for details. ! ATTENTION: Install in accordance with local and national building and electrical codes. 4/21/2025 page 2 IS-DF 01 RECESSED FIXTURE 02 LEDALITE TILES 03 CUSTOMER SUPPLIED TILES 04 CHICAGO PLENUM Table of Contents PG. 04 PG. 06 PG. 08 PG. 10 ! ATTENTION: Install in accordance with local and national building and electrical codes. 4/21/2025 page 3 IS-DF Recessed Fixture Installation Sheet Preparing fixture to mount on T-Grid. 1 Bend mounting tab 2 Place fixture in T-Grid 3 Place fixture in T-grid Bend out the mounting tabs by 90° on each corner. Place fixture in T-Grid. Bend tabs flush against T-Bar to clear ceiling tile. 4 Secure fixture & tie-off to structure (3 acceptable options) Top Tile Retention Bracket Option #1 Option #2 Option #3 Choose the option that best prevents interference with adjacent fixtures and tiles. Screws supplied by others NOTE: MAKE SURE THE GUY WIRES CLEAR THE TOP TILE RETENTION BRACKETS ! ATTENTION: Install in accordance with local and national building and electrical codes. 4/21/2025 page 4 IS-DF Wiring and connections. 5 Standard electrical connections Recessed Fixture Installation Sheet Standard electrical 6 connections 7A CAUTION Remove screw using a #2 Phillips OR #2 Robertson screwdriver to open wire access door. Make electrical connections using wire nuts (supplied by others). Optional 6' flex whip is prewired inside the fixture. Remove from packaging and insert snap-in fitting into driver box. Close access door and reinstall screw using a #2 Phillips OR #2 Robertson screwdriver. Only use these knockouts for electrical connections between fixtures. 7B OPTIONAL: Electrical connections between fixtures Fold fixture tabs (No Top 8 Tile) 9 Recycle X Remove knockouts and feed the wires through electrical conduit (supplied by others). Ensure the correct wire color code is maintained. ATTENTION: Recommended way of electrical connection between fixtures (daisy chained). NOTE: Secure flexible metal conduit to structure as per local electrical code guidelines. ATTENTION: If there is no Top Tile being used, fold both fixture tabs down so they are not visible from underneath. Recycle all packaging materials and unused contents. ! ATTENTION: Install in accordance with local and national building and electrical codes. 4/21/2025 page 5 IS-DF Top Tile Installation Sheet Ledalite Tiles Preparing Top Tile Ledalite supplied 20.5" x 20.5" size - acoustic, acrylics, metal and air return tiles by Ledalite. 1 Rotate the top brackets 2 Bend tabs up on brackets Rotate the top brackets 3 back in place Rotate both Top Tile retention brackets, inwards, about 45°. Bend both center tabs upwards on both Top Tile retention brackets. Rotate both Top Tile retention brackets back in place. 4 Bend tabs up on fixture 5 Place Top Tile 6 Fold Tabs (Air Return) Bend both fixture tabs upwards so they form a 90° angle (use needle nose pliers, if needed). Place Top Tile between the bent-up tabs. ATTENTION: For acrylic tiles, follow steps 1-4 of the Chicago Plenum section to add the metal backing plate on top of the tile. NOTE: Gloves are recommended when handling Acrylic tiles to prevent debris or marks. Also, remove the protective film from Acrylic tiles. ATTENTION: If there is an air return Top Tile being used, fold all 6 tabs down on all corners to obtain vertical retention. ! ATTENTION: Install in accordance with local and national building and electrical codes. 4/21/2025 page 6 IS-DF Top Tile Installation Sheet Ledalite Tiles Preparing Top Tile Ledalite supplied (continued) 20.5" x 20.5" size - acoustic, acrylics, metal and air return tiles by Ledalite. ! Attention 7 Finishing Make sure the tile is sitting flush with the fixture. Place adjacent grid ceiling tiles back into the grid, if they were removed, to finish installation. ! ATTENTION: Install in accordance with local and national building and electrical codes. 4/21/2025 page 7 IS-DF Top Tile Installation Sheet Customer Supplied Tiles Preparing Top Tile Customer supplied 24" x 24" nominal size - tiles for stand-alone fixtures. ! DISCLAIMER! TOP TILES MUST COMPLY WITH LOCAL BUILDING CODES AND REGULATIONS. PLEASE ENSURE ALL MATERIALS USED MEET THE NECESSARY REQUIREMENTS. ! Warning! Maximum allowable thickness is 0.75" (19mm) and maximum allowable weight is 5lbs (2.2kg) for all Top Tiles. 1 Rotate the top brackets 2 Bend tabs up on bracket 3 Bend tabs up on fixture Rotate both Top Tile retention brackets, inwards, 180°. Bend both the tabs at the ends upwards on both Top Tile retention brackets. Bend both fixture tabs upwards so they form a 90° angle (use needle nose pliers, if needed). 4 Place Top Tile 5 Finishing Place Top Tile between the bent-up tabs. NOTE: Top Tile will overhang by ~2" from the fixture Make sure the tile is sitting flush with the fixture. ! ATTENTION: Install in accordance with local and national building and electrical codes. 4/21/2025 page 8 IS-DF Top Tile Installation Sheet Customer Supplied Tiles Preparing Top Tile Customer supplied 24" x 24" nominal size - tiles for fixtures sitting back-to-back or custom tiles. ! DISCLAIMER! CUSTOM TOP TILES MUST COMPLY WITH LOCAL BUILDING CODES AND REGULATIONS. PLEASE ENSURE ALL MATERIALS USED MEET THE NECESSARY REQUIREMENTS. ! Warning! Maximum allowable thickness is 0.75" (19mm) and maximum allowable weight is 5lbs (2.2kg) for customer supplied and/or custom top tiles. 1 Cut tile to size 2 Top Tile installation 3 Finishing 20.50" 20.50" Carefully cut tile to size: 20.50" x 20.50" (521mm x 521mm). NOTE: Cutting materials from Ledalite or 3rd parties may void warranty. Follow steps 1 to 4 of "Top Tile Installation Sheet Ledalite Tiles" and then place top tiles between the bent-up tabs. Make sure the tile is sitting flush with the fixture. ! ATTENTION: Install in accordance with local and national building and electrical codes. 4/21/2025 page 9 IS-DF Top Tile Installation Sheet Chicago Plenum Preparing Top Tile Ledalite supplied 20.5" x 20.5" nominal size acoustic and acrylic tiles by Ledalite. 1 Retention bracket setup 2 Remove metal fins For Acrylic: 3 Place metal backing plate 6mm (0.23") For Acoustic: 14mm (0.54") Start by following steps 1 to 4 of "Top Tile Installation Sheet Ledalite Tiles" and then select appropriate metal backing plate for your tile (acrylic or acoustic). NOTE: Gloves are recommended when handling Acrylic tiles to prevent debris or marks. Remove all fins from the metal backing plate. Optional: Use metal snips. NOTE: Fins in the metal backing plate are for manufacturing use only and not used in installation. Place the metal backing plate on top of the tile. 4 Place Top Tile 5 Finishing Place Top Tile with metal backing plate between the bent-up tabs. ATTENTION: Ensure the Top Tile is fully covered by the metal backing plate and no edges of the top tile are visible. Make sure the tile is sitting flush with the fixture. ! ATTENTION: Install in accordance with local and national building and electrical codes. 4/21/2025 page 10 INSTALLATION WARNINGS AND INSTRUCTIONS FOR LUMINAIRES IMPORTANT: THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. FOR YOUR PROTECTION, YOU MUST CAREFULLY READ ALL WARNINGS AND INSTRUCTIONS IN THEIR ENTIRETY PRIOR TO INSTALLATION, OPERATION, SERVICE OR MAINTENANCE. FAILURE TO DO SO CAN RESULT IN DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. If you do not understand these warnings and instructions, or if additional information is desired, please contact the Customer Care Call Center at 800-555-0050. ·Installation, service and maintenance of luminaires must be performed by a qualified professional and in accordance with all federal, state and local laws, regulations and electrical codes. This professional should be familiar with the construction and operation of this product and any hazards involved. If not qualified, do not attempt installation, service or maintenance. ·To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts, abrasions and other hazards, please read all warnings and instructions included with the luminaire, on the luminaire's packaging and affixed to the luminaire itself. ·Maintenance of the luminaires should be performed by person(s) familiar with the luminaire's construction and operation and any hazards involved. WARNING RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY · Disconnect or turn off power before attempting any installation, service or maintenance. · Verify that supply voltage is correct by referencing the luminaire label information. · Make all electrical and ground connections in accordance with the National Electrical Code (NEC) and any other applicable laws, regulations or codes. · All wiring connections should be capped with UL-approved wire connectors. WARNING RISK OF PERSONAL INJURY · Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance. · Avoid direct eye exposure to the light source while it is on. WARNING RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY WARNING RISK OF FIRE OR PERSONAL INJURY · Keep combustible materials away from LED/lamp & lens. · Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying. · Allow LED/lamp & lens to cool before handling. · Do not touch enclosure or light source. · Do not exceed maximum wattage marked on luminaire label. · Follow all manufacturer's warnings, recommendations, instructions and restrictions for driver type, burning position, mounting locations and replacement. CAUTION RISK OF PRODUCT DAMAGE ·Never connect luminaires and/or components under load with supply voltage turned on. ·Do not mount or support these luminaires in a manner that can cut the outer jacket or damage wire insulation. ·Do not restrict fixture ventilation. Allow for some volume of airspace around luminaire. Avoid covering luminaire with insulation, foam or other material that will prevent convection or conduction cooling. ·Do not exceed luminaire maximum ambient temperature. ·Do not modify the luminaire. ·Only use luminaire in its intended application and location. ·LED products are polarity sensitive. Ensure proper polarity before installation. ·Electrostatic Discharge (ESD) can damage LED. Personal grounding equipment must be worn during all installation and servicing of the luminaire. ·Do not touch individual electrical components as this can cause ESD, shorten LED life, or impact LED performance. ·Some components inside the luminaire may not be serviceable. In the unlikely event your luminaire may require service, stop using it immediately and contact the Customer Care Call Center at 800-555-0050. ·Always read the luminaire's complete installation instructions prior to installation for any additional luminaire specific warnings. ·In the case of HID or Fluorescent luminaires, regular re-lamping is required to keep luminaire operating within safe limits ·Do not install damaged product. Handling and installing damaged products can potentially increase the risks mentioned. In case of damage and/or missing parts upon arrival of the luminaire, please contact the Customer Care Call Center at 800-555-0050. ·These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation or maintenance. Should further information be desired, or should particular problems arise which are not covered sufficiently for the purchaser's or owner's purposes, this matter should be referred to the Customer Care Call Center at 800-555-0050. Please see luminaire specific Installation and Maintenance Instruction for additional warnings or any applicable FCC or regulatory statements. Failure to follow any of these instructions could void luminaire warranties. Luminaire Maintenance ·Regular luminaire maintenance programs are recommended. ·It is recommended to clean the outside of the luminaire and the refractor/lens. ·Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user. ·©If2c0le24an water is not sufficient for cleaning, use a neutral, synthetic, non-scratching and non-abrasive cleaning substance. ·Never use alkaline and/or acetous cleaning substances. ·Make sure that the cleaning substance is carefully removed by rinsing with lots of clean water. ·Signify recommends using a cleaning solution that has a PH between 5 and 8. ·Recycle: For information on how to recycle electronic products and components, please visit www.epa.gov. 442294653951 - REV B 4/21/2025 page 11 ! ATTENTION: Install in accordance with local and national building and electrical codes. www.signify.com