Instruction Manual for MEMPHIS models including: VGB0002S, 39-Inch Stainless Steel Built-In Grill
Memphis Elite Built-In ITC3- with WiFi -304 Stainless Steel
File Info : application/pdf, 13 Pages, 3.02MB
DocumentDocumentVG0893 Revision: A1 Memphis Elite Built-In ITC 3 IntelliBurn TechnologyTM Model Number VGB0002S Built-In Grill Island Dimensions 3 Hardware Components 4 Grill Installation and Operation 5-9 Memphis WiFi Setup 10 11 Memphis Component Diagram 12 Memphis Fuse Diagram 13 Read all instructions before installing and using this appliance Save these instructions for future reference Clearance to Combustible Materials Combustible Material is wood, dry wall, siding or any other material that has to ability to catch fire. Built-in structures constructed of wood or other combustible materials may require the use of the OPTIONAL Built-In Heat Shield Kit to maintain the required clearance to combustible materials. The grill may be supported by either the three support brackets, or the four leveling feet. Please note that there must be at least 3/8" (1.0 cm) clearance between the bottom of the grill and the structures. DIMENSIONS A 18" [45.8 cm] B 3/8" [1.0 cm] C 2" [5.1 cm] D 3 1/2" [8.9 cm] E* 1/8" [0.5 cm] F 30" [76.2 cm] Built-in Bracket Power Cable Loca on *NOTE: Clearance dimension E may only be used when the optional heat shield kit (VGBHSK) has been installed. This distance is from the outside of the installed heat shield kit. 2 Built-In Cutout Dimensions NOTE: Dimensions are to the finished surfaces. Grill cavity surfaces are to be plumb and level to ensure a proper fit. Top View Power Requirements 110/120VAC* supply required within 10 feet of the ITC. Power cable located at the back right of the grill. (See note on previous page) *European 220VAC Front View CUTOUT DIMENSIONS A 42 5/8" [108.3 cm] B 16 3/4" [42.6 cm] C 24 1/2" [62.9] D 3 1/2" MIN [8.9 cm] E Standard Cabinet Height TOLERANCE +/- 1/8" [0.30 cm] +/- 1/8" [0.30 cm] +/- 1/8" [0.30 cm] - - 3 Description/ Part No. Qty: 1. VG0002 Grate Kit 1 2. Savorizer VGE4403 1 3. Direct Flame Insert VG4407 1 4. Genie Tool VG1595 1 5. Bracket Bolt DS2311 10 6. Antenna VG9023 1 7. #10 Screw (SS) DS2186 2 8. Cord Wrap VG0560 1 9. Meat Probe VG0956 1 10. Leveling Feet DS4668 4 11. Concrete Anchor DS2349 2 12. #10 SS PH Screw DS2350 2 Hardware Components Picture: Description/ Part No. Qty: 13. Left Mounting Bracket VG0803 1 14. Right Mounting Bracket VG0802 1 15. Right Mounting Bracket VGE0801 1 OPTIONAL 16. Heat Shield VGBHSK 1 Picture: 17. #10 Screw (BLK) DS2185 4 TIME REQUIRED 1.5 Hours TOOLS REQUIRED 3/8" Open End Wrench, Socket or Adjustable Wrench Phillips Screw Driver or Drill Snips or Heavy Duty Scissors Cut Resistant Gloves 5mm Allen Wrench 4 Grill Installation and Operation Installation Requirement A dedicated GFCI protected electrical circuit is required for all Memphis Wood Fire Grills and controller systems. This circuit should be installed by a Certified Electrician. Although the Memphis Grill only uses about 2 amps of current during startup, any other equipment (refrigerator, pool pump, fountains, ect.) that have high current draw, consistently or intermittently, from the same electrical circuit can cause potential issues and/ or interruptions with the performance of the grill. We recommend an on/off switch to be installed in this circuit so that the grill can be easily disconnected from power when not in operation. This will prevent the buildup of interference that could affect the controller's operation. Hopper Lid Orientation For easier pellet refill, the hopper lid can be oriented to open toward the front of the grill instead of the rear when access to the back of the grill is difficult or unavailable. To switch the orientation to be opened from the front, the shoulder bolts holding the hopper lid must be removed. Rotate the lid so the mounting holes are towards the back of the grill. Re-insert shoulder bolts into the rivnuts towards the back of the grill. *Note: The fill shield must be flipped up to cover the smoke vent in this orientation. This is used to block pellets from falling into the grill via the smoke vent. Other Grill Information Main Grate Area 37.1 in X 17.4 in. [94.3 cm X 44cm] Top Grate Area 37.1 in. X 5.5 in [94.3 cm X 14 cm] Optional Middle Grate Kit Area 37.1 in. X 11 in [94.3 cm X 28 cm] 644 in. sq. 204 in. sq. 408 in. sq. [4,149 cm sq.] [1,320 cm sq.] [2,640 cm sq.] Grill Height with Hood Open 47.1 in. [120 cm] 5 Installation Step 1: Unpacking Grill requires (2) two people for safe assembly Please note that during shipping some movement may have taken place, so a complete visual inspection is required. Be sure to inspect entire grill after removing the protective shipping carton. Report any damage to your local dealer immediately. Shipping damage is not covered under warranty. Some surfaces may be sharp so wear gloves when assembling. Do not plug in the grill until it's fully assembled, the plastic protective film is removed from all stainless steel surfaces, and you're ready to cook. See: "Startup Procedure" in the General Owners Guide for more details. 1. Remove the Savorizer (item 2) and included grates (item 1) from inside the grill hood. To remove the Savorizer, cut the 4 zip ties holding it in place. Set aside grates and Savorizer until needed. 2. Peel all plastic protective film from the grill. Be diligent about inspection as the protective film will be hard to remove once the grill is installed and first burned. Installation Step 2: Wiring Follow the assembly steps listed below, prior to installation of the unit. 1 3. Remove two 5mm socket head screws from Display Housing shipping bracket using the 5mm allen wrench. 4. Snip the zip tie that secures the Display Housing to the shipping bracket and dispose. This bracket is no longer needed. 5. Mount the Display Housing perpendicular to the side panel over the Display Insert bracket using the two 5mm x 40mm socket head screws in the hardware kit. The original 5mm screws can be disposed of. 6. Install Wifi Antenna (item 6) to bulkhead connector located on the right panel of the grill behind the Display Housing. Packaging Locations Savorizer Grates Hardware Kit Mounting Brackets 3 4 6 5 6 Installation Step 3: Brackets Follow the assembly steps listed below, prior to installation of the unit. The Unit can be supported by either the support brackets (items 13, 14, and 15) or by the four leveling feet (item 10). Refer to page 4 for item part numbers, descriptions, and quantities. Note that the support brackets must be installed for either support method. 7. Remove the ash/grease drawers from the unit. 8. Fasten the left and right support brackets (items 13 and 14) to the unit using the ten 1/4"-20 stainless steel hex bolts (item 5). 9. Fasten the rear support bracket (item 15) to the left and right support brackets (items 13 and 14) with two #10-24 x 1/2" long stainless steel screws (item 7). 10. This step is only to be done if the grill is going to be supported by the four leveling feet (item 10) and not the support brackets. Thread the four leveling feet (item 10) into the bottom of the unit. Optional: 11. To reduce the clearance to combustible materials, the optional heat shield kit should be used. Refer to page two to determine if the heat shield kit is required for your installation. Follow the assembly instructions provided with the heat shield kit to properly fasten the kit to the unit. 7-10 11 7 Installation Step 4: Grill Mounting 12. Place the unit into the island and position it to the desired depth. Ensure that the vent holes in the support brackets are unobstructed for properly air circulation. 13. Locate the two mounting holes found in the back of the left and right support brackets (Items 13 and 14), and mark the hole locations onto the island's countertop. 14. Carefully slide the unit out of the island, exposing the marked holes on the countertop. 15. Drill two 5/16" holes into the countertop using a drill bit appropriate for the material of the countertop. 16. Insert two concrete anchors (item 11), into the two 5/16" holes. 17. Slide the unit back into position, lining up the mounting holes in the left and right support brackets with the concrete anchors. 18. Fasten the unit into place using the two 1 3/4" long stainless steel screws (item 12). Do not over-tighten. Mounting Holes 12-13 14-16 17-18 8 Installation Step 5: Final Assembly Refer to page 4 for item part numbers, descriptions, and quantities. 19. Inset the three ash/grease drawers back into the unit. 20. Place Savorizer (item 2) onto the left and right lower brackets found inside the unit. 21. Place the main cook grates (item 1) onto the front and rear supports. Place the upper cook grate (item 1) onto the left and right upper brackets found inside the unit. Vent holes on the mounting brackets must remain unobstructed for proper air circulation. Grill must be accessible (able to slide out) for any future repair or maintenance. Refer to the Owners Guide for first time use instructions. 9 MEMPHIS WI-FI SET UP GUIDE ON YOUR GRILL CONTROLLER: 1. Navigate to the Settings Screen on the display. 2. Select "Connect to WiFi" to navigate to the Connection Screen. 3. Press the blue "Connect WiFi" button to broadcast the BLE signal. 4. Follow the steps below on your Memphis 3 App. ON YOUR PHONE OR TABLET: (In Memphis 3 App) 5. Log into Memphis 3 App using your account email and password. 6. If no grill is connected, the BLE provisioning process will begin automatically. Otherwise, navigate to the Setting Screen and select "Add Grill". 7. Select your grill from the provisioning screen. 8. Select the 2.4GHz network you would like to connect to your Memphis grill, enter the network password, and press "Provision". 9. If successful, the controller will display "Connection Successful" and show the WiFi signal strength in the top right corner. *Note: If a red X is displayed on the controller instead of the signal strength the connection was unsuccessful. Attempt to provision the controller again, otherwise contact Memphis Technical Support. GRILL NETWORK INFORMATION Navigating back to the "Connect to Wifi" Screen displays the Network information as well the MAC Address and IP Address of your Memphis Grill. 10 Memphis Controller Diagram Part # VG1966 VG1967 VG1968 VG1969(E) VG1970 VG1971 VG1972 VG1973 VG1975 VG1976 VG1977 VG1978 Name Auger Wiring Harness Blower Wiring Harness Display Wiring Harness US Power Cable (Euro) IO Wiring Harness Probe Jack Wiring Harness Push Button Wiring Harness 5V Wiring Harness Igniter Wiring Harness Auxiliary Fan Wiring Harness RTD Wiring Harness 24V Wiring Harness VG1979 VG9026 VG0326 VG0327 VG0328 Cook Light Wiring Harness Wifi Jack Logic Board IO Board Power Supply Board Description 5 pin connector from auger motor to the logic board 4 pin connector from blower to the logic board 9 pin connector from the LCD display to the logic board Power cable that plugs into 120VAC (US) or 240VAC (EU) wall outlet 8 pin connector from IO board to the logic board 2 pin connector from meat probe jack to the IO board 4 pin connector from push button in the Display Housing to the IO board 4 pin connector from power supply board to the logic board 2 pin connector from igniter to the logic board 2 pin connector from Aux fan to logic board 2 Pin connector from RTD to the logic board. Connection to board is non-polarized 2 pin connector from power supply to logic board. Provides power to blower, aux fan, auger motor, cook lights and LCD 2 pin connector from cook lights to logic board Single conductor jack installed in right panel connected to the logic board Controls components related to smoking and cooking Controls push button and meat probe jacks Provides 24V DC and 5V DC power 11 Memphis Component Diagram Part # VG9501 VG1967 VG1968 VG1969(E) VG1971 VG1972 Name Auger Motor Blower LCD US Power Cable (Euro) Probe Jack Push Button VG1975 VG1976 VG1977 Igniter Auxiliary Fan RTD VG1980 Cook Lights VG9026 VG9027 WiFi Jack WiFi Antenna Description This component rotates the auger to supply fuel into the burn pot This component pulls air from the lower cabinet and into the firebox for combustion Used to display Grill information and change grill settings Power cable that plugs into 120VAC (US) or 240VAC (EU) wall outlet This component is used to plug probes for monitoring meat temperature This component is used to set the grill to cooldown, reset the controller, or put the display to sleep This component provide the initial heat during startup This component supplies cooling for the power supply and logic boards This component is used by the controller to determine the cook chamber temperature These components are mounted inside the cook chamber to provide light to the cook Single conductor jack install in right panel connected to the logic board 2.4GHz WiFi antenna 12 Memphis Fuse Diagram Power Cable (VG1969) Fuse VG9021 Fuse Glass 250VAC 5A 5 x 20 mm Antenna Jack Connector Logic Board Layout MicroSD 4A SLO-BLO Fuse 0.5A SLO-BLO Fuse 12A SLO-BLO Fuse 13Acrobat Distiller 20.0 (Windows)