Spionlink - SIM Card Service | Prepaid Data Plan | GPS Tracker Supplier
User Manual for MiCODUS models including: ML500G, ML500G Mini 4G Car GPS Tracker, ML500G, Mini 4G Car GPS Tracker, 4G Car GPS Tracker, Car GPS Tracker, GPS Tracker
9 ore fa — ML500G User Manual V2.0. Learn how to set up your new MiCODUS Tracker ... User Manual. Quick User Guide. Genuine Packing Box (Optional). Hard-Wired Car ...
Quick User Guide. Genuine Packing Box (Optional). Hard-Wired Car Charger ... start working via mode 2 at 09:00am, and it will upload data every 1 hour ...
File Info : application/pdf, 10 Pages, 2.05MB
DocumentDocumentR ML500G User Manual V2.0 Learn how to set up your new MiCODUS Tracker Copyright ©2025 MiCODUS | All Rights Reserved 1. Main Features Real-time Historical Route Powerful Tracking Playback Magnet 5000 mAh Waterproof 7-10 Days IP65 Working Time Voice Monitor Shift alert Corner Overspeed Vibration Geo-fence Teardown Temperature Low battery Uploading Alarm Alarm Alarm Monitor alert 2.Specifications Device Information Working Parameters Model Weight Dimensions Charging Time Battery Working Time Working Voltage Working Current Sleep Current Battery Capacity Working Temperature Working Humidity Working Frequency Cellular Specifications SIM Card Cellular Antenna Positioning Type GPS Antenna GNSS Specifications Cold Start Hot Start Tracking sensitivity GPS Channels ML500G 172g 85mm(L) * 49mm(W) * 30mm(H) Around 7 hours Tracking Mode, 1 minutes' reporting: 10 days DC 3.4V - 4.5V 4V/Average 45mA 4V/less than 5mA 3.7V 5000mAh Lion Polymer battery -20¥ - 75¥ 10%-85%RH non-condensing 4G LTE CAT1 :LTE-FDD:B1/B2/B3/B4/B5/B7/B8 /B20/B28/B66 LTE-TDD: B34/B38/B39/B40/B41 2G GSM/GPRS/EDGE: 850/900/1800/1900MHz Micro SIM Card Built-in GPS+GLONASS+BEIDOU+LBS Built-in 32 Seconds 1 Second -162 dBm 64 Temperature Sensor External Interface Position Accuracy 5-10m Scope Accuracy 40¥ to 125¥ ±1¥ Microphone, Light Sensor, Temperature Sensor 3. Activate Device Install the SIM card via the correct direction as below: 11MMBBFFrereee PrPerpeapiadidDDataata DDaatataOOnnlyly NNo oSMSMSS&&CCalal ll RRooaamminingg UUnnaavvaailialabblele wwwwww.s.sppioionnlilninkk..ccoomm AAddddCCreredditit TTooppUUpp Normal SIM LED POWER LED (RED) CELL LED (YELLOW) GPS LED (BLUE) ALL LED Event Charging Charger inserted and battery has been fully charged Charger has not been inserted Searching for network Network has been registered GPS is in fixing GPS has fixed Device is working but stopped more than 5min Device has not been turn on Device ran out of battery State Solid Dark Dark Flash every 1 second Solid Flash every 1 second Solid ALL LED TURN OFF Please get the exact correct APN name from local SIM card provider.Take the tracker to a good signal place for operation and configure the APN for it as below: 4.4$PNNBOE 'PSNBU APN,ApnName,User, Password# 3FQMZ &YBNQMF /PUF SET APN OK APN,orange, orange,orange# If the SIM card has APN user and APN password, then use this command. APN,ApnName# SET APN OK APN,internet# If the SIM card operator doesn't have APN user and APN password, then plea se use this command. Note: The APN information is very important, it must 100% correct to match with the sim card of the tracker, if you configured wrong APN, the tracker also will reply "SET APN ok" but it will can't get online! 4. Package Content GPS Main Unit x 1 USB Charging Cable x 1 User Manual x 1 Quick User Guide x 1 Genuine Packing Box (Optional) x 1 Hard-Wired Car Charger (Optional) x 1 5. Functions Explanation Please follow with the quick user guide carefully! a. Working modes setting * ML500G has 3 working modes to meet different tracking demands, the setting command format is as below: MODE,A,T1,T2# A=1 (Tracking mode) T1: upload interval of GPS data in moving status, unit: second,10-3600s; default: 10s T2: upload interval of GPS data in static status, unit: second, 180-65535s; default: 3600s A=2 (Power saving mode) T1: interval start time,format: HH:MM T2: time interval,range: 1-72 unit: hour,default interval: 24hours A=3 (Hibernation mode) T1: interval start time,format: HH:MM T2: time interval,range: 1-72 unit: hour,default interval: 24hours For example: ML500G MODE,1,10,3600# SET MODE OK MODE,2,0900,1# SET MODE OK MODE,3,0900,1# SET MODE OK * Example: MODE,1,10,3600# (this means the device will upload data by 10s interval under moving status and 3600s interval under stationary status) MODE,2,0900,1# (this means the device will start working via mode 2 at 09:00am, and it will upload data every 1 hour) MODE,3,0900,1# (this means the device will start working via mode 3 at 09:00am, and it will upload data every 1 hour) * Note : The difference between mode 2 and mode 3 is that under mode 2 the device can be wake up by sms, call and vibration, under mode 3, the device will just can be wake up by teardown alarm. b. Voice Monitor: * Set center number by this sms command: CENTER,password,A,center number# * Switch the tracker to voice monitor mode by this sms command:MONITOR# * Dial the sim number of the tracker from the center number, then the tracker will pick up the call automatically and you will can remote monitor the voice around it. For example: ML500G CENTER,888888,A,134********# SET CENTER NUMBER OK MONITOR# SET MONITOR MODE OK c. Vibration Alert: For example: This vibration alert function just work under stationary status. How to use this function: * Configure SOS numbers for the tracker by this sms command:SOS,A,1st number,2nd number,3rd number# 3 SOS numbers supports at the most ML500G SOS,A,134********# SET SOS NUMBER OK ARM# SET ARM MODE OK * Enable the device to enter into arm mode by this sms command: ARM# SENALM,ON,1# SET VIBRATE ALARM OK * Conifgure the alarm ways by this sms command: SENALM,[A][,M]# A=ON/OFF, default: OFF; M=0/1/2, way of alarming, 0 :GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+phone call, default:1 * Keep the device under stationary status more than 5min to let it enter into sleep arm mode; * Vibrate the device then the tracker will send the vibration alarm messages d. Tearndown Alert * Configure SOS numbers for the tracker by this sms command:SOS,A,1st number,2nd number,3rd number# 3 SOS numbers supports at the most * Enable the device to enter into arm mode by this sms command:ARM# * Configure the alarm ways by this sms command: TEARDOWN,A,M# A=ON/OFF; default:ON M=0/1/2; way of alarm, 0 : GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+CALL, default:1 For example: ML500G SOS,A,134********# SET SOS NUMBER OK ARM# SET ARM MODE OK TEARDOWN,ON,1 SET TEARDOWN ALARM OK 6. Installation Recomendation 6 5 1 4 3 2 æDriving seat sundries box çFront bumper èDoor sundries box éUnder the chassis êRear windscreen ëRear bumper 7. Troubleshooting Type Unable to connect to tracking platform Tracker shows offline Unable to locate Location drift No command reply Use Check the APN and settings. Check whrther the data service of SIM card is enabled. Check the balance of SIM card. Check whether external power is still connected. Check if the vehicle entered netword blind area. Check the balance of SIM card. Make sure the top side facing upward without metallic things shielded. Make sure it's not in area with no satellite coverage. In area with poor GNSS signal (tall building around or basement), drifting may happen. Check whether vibration happens around to trigger the accelerator. Make sure command format is correct. Vehicle may be in network blind area. Make sure SIM card is well inserted and has SMS servi. 8. Full SMS Commands List Functions APN Setting Command Format Explanation APN,CMNET# (if no name & Password) APN,Network name[,name,password]# APN,internet,internet,internet# (if with name & Password) Server Setting Revise the instruction password Check IMEI If set with Domain Name: SERVER,1, Domain,Port# If set with IP: SERVER,0,IP,Port# PASSWORD,[A],[B]# IMEI# SERVER,1,d.micodus.net,7700# SERVER,0,47.254.77.28,7700# A=old password, six digitals, digital range: 0-9, default000000; B=new password, six digitals, digital range: 0-9 Change IMEI IMEICHG,354188046912460# Restore factory settings FACTORY# Version Inquiry VERSION# NEW IMEI No. : 354188046912460 Parameter Inquiry PARAM# Latitude&Longitude Inquiry Map URL Inquiry WHERE# URL# Check All Alarms Status ALARM# Status Inquiry STATUS# Time Zone Setting GMT,Time zone orientation,Whole Time Zone[,Half Time Zone]# Check ID,IMEI,APN, IP,PORT,TIMER,Center number,SOS number,Time Zone BATTERY: XX% (Built-in Battery Power Percent) NET: CLOSED (No Network) FAILED (Connecting Network or Failure) SUCCESS(Connected to Network), NONE (No GSM Signal) HIGH / MED / LOW (Signal Strength) GPS: CLOSED (GPS Module Closed) FIXED, N(Positioned and satellite number) UNFIX, 0 (Not Positioned yet) TEMPERATURE: 30°C(the temperature around the device) ANGLE: 20 (the data upload angle) SENSOR: ON/OFF (the status of the shake sensor) LEVEL: 3 (the sensitivity of the shake sensor) STATE: ARM/DISARM (the defense status of the device) GMT,E,8# (if no half time zone) GMT,W,9,30# (if has half time zone) NOTE: Parameter : E / W; 0 ~ 12; 0/15/30/45 Functions Set the angle upload Mileage Statistics Add SOS Administrator Number Delete SOS Administrator Number Command Format Explanation ANGLEREP,[X][,A][,B]# X=ON/OFF,default:ON; A=5~180 degrees,diversion angle degree, default: 30 degrees;B=2~5 seconds, detecting time, default: 3 seconds. ANGLEREP,OFF# MILEAGE,[A],[B]# MILEAGE# A=ON/OFF, On/Off mileage calculation, default: Off B=0~999999, Mileage initial value , unit: km ; default: 0, mileage return to zero Query current mileage SOS,A,1st number,2nd number, 3rd number# Set 3 numbers at a time: SOS,A,13800138000,1380013800 1,13800138002# Set the first numberseparately: SOS,A,13800138000# Set the second number separately: SOS,A,,13800138001# Means to set 3rd number separately: SOS,A,,,13800138002# SOS,D,1st number,2nd number, 3rd number# or SOS,D,1,2,3# Directly delete the number: SOS,D,13800138000# Delete 1st number: SOS,D,1# Delete 2nd number: SOS,D,2# Delete the 2nd and 3rd number: SOS,D,2,3# Add Center Number CENTER,password,A, center number# Example: CENTER,888888,A,+8613800138000# Note: Please set up the center number with the country code as prefix! Delete Center Number Set the instruction password CENTER,password,D# PWD,password,ON# PWD,password,OFF# Example: CENTER,888888,D# Enable instruction password successfully! Cancel instruction password successfully! Change the instruction password PWDCHG,[A],[B]# A=old password, six digitals, digital range: 0-9, default888888; B=new password, six digitals, digital range: 0-9 Reset password RSTPWD,A# A=ID Number, ID number of the device; Data Upload Time Zone Setting DATAGMT,Time zone orientation,Whole Time Zone [,Half Time Zone]# DATAGMT,E,8# (if no half time zone) DATAGMT,W,9,30# (if has half time zone) NOTE: Parameter : E / W0 ~ 12; 0/15/30/45 Functions Command Format Working Mode Setting MODE,A,T1,T2# Sleep Mode Setting Voice Monitor Mode Track Mode Heartbeat Packet Upload Sensor Sensitivity Arm manually Disarm manually Overspeed Alarm Setting Vibration Alarm Setting SLEEP# SLEEP,OFF# MONITOR# TRACK# HBT,time# MOTION,sensitivity# ARM# DISARM# SPEED,[A][,B][,C]# SPEED,OFF# SENALM,[A][,M]# SENALM,OFF# Shift Alarm Setting SHIFT,[A][,B][,M]# SHIFT,OFF# Explanation A=1/2/3, 1:Tracking mode 2:Power saving mode 3:Hibernation mode; Default mode: 1 A=1 T1: upload interval of GPS data in moving status, unit: second,10-3600s; default: 10s T2: upload interval of GPS data in static status, unit: second, 180-65535s; default: 3600s A=2 T1: interval start time,format: HH:MM T2: time interval,range: 1-72 unit: hour,default interval: 24hours A=3 T1: interval start time,format: HH:MM T2: time interval,range: 1-72 unit: hour,default interval: 24hours NOTE: After set this sleep mode, the device will enter into sleep mode automatically when the device keep stationary status more than 5min. NOTE: Before monitoring the voice around the device, the user must change the device to this monitor mode firstly. NOTE: After used the voice monitor mode, user can switch the device back to track mode by this command. HBT,3# NOTE: Range :1-60min, default 3min. MOTION,2# NOTE: Sensitivity Level1-9 (1-9 is from week to strong vibration) Set the device into arm mode Set the device out of arm mode A=ON/OFF, open or close over speed alarm, defaultOFF B=1j255(km/h), speed limit, default100(km/h); C=0/1, way of alarm, 0 : GPRS only, 1: SMS+GPRS, default1. A=ON/OFF, default: OFF; M=0/1/2, way of alarming, 0 :GPRS only, 1: SMS+ GPRS, 2 : GPRS+SMS+phone call, default:2 Example: SHIFT,ON,100,1# ( Means Setting 100 meters shift alarm range, when the ignition turned off, vehicle's 100 meters' shift will trigger the alarm.) A=ON/OFF; default:ON B=Shift Distance (Range: 100-9999m) M=0/1/2; way of alarm, 0 : GPRS only, 1: SMS+ GPRS, 2: GPRS+SMS+CALL, default:1 Functions Disassemble Alarm Setting Temperature Alarm Setting Low Battery Alarm Setting Command Format TEARDOWN,A,M# TEARDOWN,OFF# TEMP,ON,10,20,1# TEMP,OFF# BATALM, [A][, M]# BATALM,OFF# Explanation A=ON/OFF; default:ON M=0/1/2; way of alarm, 0 : GPRS only, 1: SMS+ GPRS, 2: GPRS+SMS+CALL, default:1 Example: TEMP,-1,50,2# NOTE: A: ON/OFF, Default: OFF L: (LOW TEMPERATURE, Range:-40¥~125¥); H: (HIGH TEMPERATURE, Range:-40¥~125¥) M=0/1/2, way of alarming, 0 :GPRS only, 1: SMS +GPRS, 2 : GPRS+SMS+phone call, default:2 A=ON/OFF, defaultON; M=0/1, way of alarming, 0: GPRS only, 1: SMS+GPRS, default1 9. Any Questions? E-mail: support@micodus.com Skype: MiCODUS 10. Download the APP Search "MiCODUS" in iOS APP store or Google Play Store, or just scan the QR code as below to download MiCODUS APP: Download on the APP Store Download for Android HarmonyOS