Blustream Home . Blustream
blustream.co.uk
User Guide for BLUSTREAM models including: DA22OPT Dante Digital Signal, DA22OPT, Dante Digital Signal, Digital Signal, Signal
The DA22OPT also supports AES67 RTP audio transport. Introduction. DA22OPT. Quick Reference Guide. • Encodes 2ch optical S/PDIF audio to ...
18 ore fa — Sound Bar. FCC NOTICE. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules ...
6 hours ago — The DA22OPT also supports AES67 RTP audio transport. Introduction. DA22OPT. Quick Reference Guide. • Encodes 2ch optical S/PDIF audio to ...
File Info : application/pdf, 4 Pages, 1.17MB
DocumentDocumentDA22OPT Quick Reference Guide DA22OPT QUICK REFERENCE GUIDE Introduction Our DA22OPT has been designed to both encode 2ch optical S/PDIF audio to a Dante® digital signal, and decode a Dante® digital signal to 2ch optical S/PDIF audio. The DA22OPT is a plug & play device that is powered using PoE (Power Over Ethernet). The DA22OPT also supports AES67 RTP audio transport. FEATURES: · Encodes 2ch optical S/PDIF audio to a Dante® digital signal · Decodes a 2ch Dante® digital signal to optical S/PDIF audio · Supports: 44.1, 48, 88.2 & 96 KHz sample rates @ 16, 24 & 32 Bit · Configurable Dante® device latency (supports 2, 3, 4, 5 or 10ms configurable using Dante® Controller) · +6dB / -24dB input sensitivity and output gain control adjustment · Supports AES67 RTP audio transport · Features Class 0 802.3af PoE for powering of product from any PoE switch · Local 12v power supply input for when network switch does not support PoE* * PS121PH power supply sold separately Front Panel 1 2 Rear Panel 3 4 Side Panel 5 Connections: 1 DC Input - Connect to +12VDC power supply (not supplied) if device is not powered via a PoE switch 2 Dante® Audio Input/Output - RJ45 socket connects Dante® network and powers device via PoE 3 Optical S/PDIF Digital Input - 2ch optical digital audio input to Dante® 4 Optical S/PDIF Digital Output - 2ch optical digital audio output from Dante® 5 Reset Switch - Press and hold to reset device Contact: support@blustream.com.au | support@blustream-us.com | support@blustream.co.uk 01 DA22OPT QUICK REFERENCE GUIDE Dante Controller Dante Controller software is required in order to setup and configure the DA22OPT as well as control your Dante network. Audinate provide extensive training videos and documentation on their website. This can be found here: http://www.audinate.com/products/software/dante-controller Upon connecting your DA22OPT to a compatible network, the Dante Controller software should automatically discover the device. The DA22OPT will appear in the Dante Controller with a name denoted with "DA22OPT". On the "Routing" screen you can create audio routing between Dante transmitters and receivers in your system. Please ensure your PC is on the same network as your Dante devices. Dante is not able to transmit over WiFi and it is recommended to hardwire into the Dante network. Having multiple network devices enabled can also confuse the Dante Controller software so it is recommended to disable WiFi during configuration. It is also possible to change the settings of the DA22OPT under the "Device Info" screen in the Dante Controller software. To do so, select the "Device Config" menu. Here we can adjust the sample rate and the encoding bit rate of the DA22OPT. Please note that Dante products can only transmit or receive audio from other Dante products that are set up with the same sample rate. A mismatch in sample rate may stop audio from transmitting. Under the "Device Config" screen we can also adjust the latency of the DA22OPT from 2, 3, 4, 5 or 10 milliseconds. 02 www.blustream.com.au | www.blustream-us.com | www.blustream.co.uk DA22OPT QUICK REFERENCE GUIDE Web Interface Module The DA22OPT features an in-built Web GUI which can be used for control and configuration of the device. By default the device is set to DHCP, however if a DHCP server (eg: network router) is not installed the device will receive a link local address in the 169.254.xxx.xxx range. The device info screen of Dante Controller will provide you with the IP address information of each unit. By accessing the IP address of the DA22OPT in your web browser, you will gain access the the units web GUI. The following details will allow you to log in to the admin section: Default Username is: blustream Default Password is: 1234 This will provide access to change the network settings to meet your systems requirements. Settings Page: Contact: support@blustream.com.au | support@blustream-us.com | support@blustream.co.uk 03 DA22OPT_REVA2_QRG Example Schematic DA22OPT 1G Network Switch DA22OPT QUICK REFERENCE GUIDE Dante® Controller 4K UHD DISPLAY CAT Cable Optical Audio Sound Bar Specifications Audio Input/Output Connectors: 1 x RJ45, female (100 Mbps Dante® network) 2 x Optical Toslink (S/PDIF) Casing Dimensions (L x W x H): 120mm x 47mm x 26mm Shipping Weight: 0.3 Kg Operating Temperature: 32°F to 104°F (0°C to 40°C) Storage Temperature: - 4°F to 140°F (- 20°C to 60°C) Power Supply: Class 0 IEEE 802.3af POE PD or 5V USB Package Contents · 1 x DA22OPT · 1 x Quick Reference Guide Acknowledgements Dante® is a registered trademark of Audinate Pty Ltd. Certifications FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. CAUTION - changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CANADA, INDUSTRY CANADA (IC) NOTICES This Class B digital apparatus complies with Canadian ICES-003.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. CORRECT DISPOSAL OF THIS PRODUCT This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling. · Consult the dealer or an experienced radio/TV technician for help. 04 www.blustream.com.au | www.blustream-us.com | www.blustream.co.uk