Installation Guide for PHILIPS models including: DTE1210 Trailing Edge Dimmer Controller, DTE1210, DTE1210 Dimmer Controller, Trailing Edge Dimmer Controller, Dimmer Controller
File Info : application/pdf, 4 Pages, 1.16MB
DocumentDocumentDTE1210 Trailing Edge Dimmer Controller Installation Instructions Instructions d'installation Installationsanweisungen Instrucciones de instalación Istruzioni per l'installazione Installatie-instructies Devices must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations. Les appareils doivent être installés par un électricien diplômé conformément à tous les codes et réglementations électriques et de construction nationaux et locaux. Die Geräte sind von einem qualifizierten Elektriker in Übereinstimmung mit allen geltenden Vorschriften zu installieren. Los dispositivos deben ser instalados por un electricista calificado y cumpliendo todas las normas y regulaciones, tanto nacionales como locales, sobre instalaciones eléctricas y obras. I dispositivi devono essere installati da un elettricista qualificato in conformità con le norme locali e nazionali vigenti in materia di costruzioni edilizie e installazione di impianti elettrici. De apparaten moeten worden aangebracht door een gekwalificeerde elektricien en in overeenstemming met alle nationale en plaatselijke elektriciteits- en bouwvoorschriften. / . X 4 X 4 1 30 mm (1.18 in) 30 mm (1.18 in) 620 mm (24.40 in) 600 mm (23.62 in) X 4 RJ12 206 mm (8.11 in) 202 mm (7.95 in) 286 mm (11.25 in) 200 mm (7.87 in) 200 mm (7.87 in) 200 mm (7.87 in) IEC Pollution Degree II 200 mm (7.87 in) 40° C (104° F) 0° C (32° F) 90% 2 3 2 4 10 A/CH 120 A 16 mm2 6+ AWG 1.5 Nm 13.3 Lb-in L CH1 N CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 5 mm2 10+ AWG 2.0 Nm 17.7 Lb-in 5 CH1 N CH2 N CH3 N CH4 N CH5 N CH6 N CH7 N CH8 N CH9 N CH10 N CH11 N CH12 N µP L1 L2 L3 N E 1 230 V ± 14% 63 A = 3 230/400 V ± 14% 3 x 40 A SELV/Class 2 (UL) µP backup power + 12 V 1 A D - DMX D + Rx 2 x RJ12 AUX/ UL924 RS-485 DyNet DMX Rx +12 V D - D + GND SHIELD 12 V 200 mA IEC Overvoltage Category III 6A 1 16 mm2 6+ AWG 1.4 Nm 12.4 Lb-in 6B 3 16 mm2 6+ AWG 1.4 Nm 12.4 Lb-in L1 L2 L3 N 16 mm2 6+ AWG 2.0 Nm 17.7 Lb-in L1 L2 L3 N 16 mm2 6+ AWG 2.0 Nm 17.7 Lb-in 3 7A 7B AUX/UL924 +12 V DD+ GND SHLD +12V +12V DD+ GND GND 2 A RS-485 DyNet GND AUX/UL924 <20 m 0.3-2.5 mm2 22-12 AWG 0.4 Nm 3.5 Lb-in 1 GND 2 GND 3 D+ 4 D 5 +12V 6 +12V 8 9 RS-485 DyNet RS-485 DyNet Apply de-rating for electronic and LED loads. Not compatible with magnetic transformers. The manufacturer is not responsible for dimmable lamp selection. Each lamp/dimmer combination must be tested for compatibility prior to installation. Professional dimmers rated > 1000 W are out of scope of EN 61000-3-2. © 2022 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners. www.dynalite.com AZZ 422 0922 R16