Instruction Manual for BAG RIDERS models including: v16 PRO Control System, v16, PRO Control System, Control System, System
In order to make mounting your manifold / ECU as straightforward as possible, we have created an easy-to-use, printable drilling template. Instructions for ...
Use these buttons to select which pair of air springs are adjusted when using individual or paired control buttons. Front Only / Rear Only Buttons. REAR. FRONT.
Use these buttons to select which pair of air springs are adjusted when using individual or paired control buttons. ... HEX NIPPLE. 7.5 AMP FUSE. 40 AMP FUSE.
File Info : application/pdf, 2 Pages, 3.01MB
DocumentDocumentFigure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 PRO Control System Instruction manual 1 2 3 Controller Layout App Connection Status Left Front Corner Pressure Left Rear Corner Pressure Front Only Control Indicator Pressure Preset 2 Pressure Preset 1 Left Up Button Paired Up Button Left Down Button Front Only Control Button 70 68 Front 14.0V 130 Psi 70 68 Rear 1 23 FRONT REAR Air Compressor Indicator Air Tank Pressure Display Right Front Corner Pressure Right Rear Corner Pressure Rear Only Control Indicator Pressure Preset 3 Air Out Button Right Up Button Paired Down Button Right Down Button Rear Only Control Button App Connection Status Connected Not Connected This indicator tells you if your PRO Control System has established a connection with your mobile app. Left / Right Front Corner Pressure Pressure of left / right front air spring. Left / Right Rear Corner Pressure Pressure of left / right rear air spring. Manual Adjustment Pressure Preset 1 | 2 | 3 Easy pressure presets you can return to anytime. Left Up / Right Up Buttons Left Down / Right Down Buttons Use these buttons to adjust air pressure of individual air springs. Air Out Button Use this button to automatically release all air pressure from all 4 air springs at the same time. Paired Up / Down Buttons Use these buttons to adjust the air pressure of both front or rear air springs at the same time. Front Only / Rear Only Buttons Use these buttons to select which pair of air springs are adjusted when using individual or paired control buttons. Air Compressor Indicator This red dot apprears when your compressor is active. Air Tank Pressure Display This shows you the current pressure in your air tank. 70 68 Front 14.0V 130 Psi 70 68 Rear 70 68 Front 14.0V 130 Psi 70 68 Rear 70 68 Front 14.0V 130 Psi 70 68 Rear 1 23 1 2 3 1 2 3 Table of Contents Controller Layout Adjusting Your Pressure Front Rear Front & Rear 1 Mobile App / Connection 6 Serial Numbers 2 Download Mobile App App / PRO System Connection Wiring & Plumbing Diagram 7 Manual Adjustment 3 Manifold / ECU Mounting 8 Front Right & Left Air Spring Adjustment Rear Right & Left Air Spring Adjustment Front & Rear Air Spring Adjustment Mounting Instructions Mounting Template Presets 4 Pressure Preset Buttons Saving Pressure Presets Using A Pressure Preset All Down Overwriting Pressure Presets Failed Pressure Preset Settings Menu 5 Opening the Settings Menu Navigating the Settings Menu Navigating Options Minimum / Maximum Tank Pressure Front / Rear Weight Adjustment Ignition On / Off Preset Figure 1 Figure 2 Figure 3 Adjusting Your Pressure 70 68 Front 14.0V 130 Psi 70 68 Rear 1 23 70 68 Front 14.0V 130 Psi 70 68 Rear 1 2 3 70 68 Front 14.0V 130 Psi 70 68 Rear 1 23 REAR Front When the FRONT button is pressed, the controller is unlocked. The FRONT button as well as the Front indicator on screen will turn red. This indicates that you are now adjusting pressure of the front air springs. Press again to re-lock. Presets 70 68 Front 14.0V 130 Psi 70 68 Rear 1 23 FRONT REAR FRONT REAR Rear When the REAR button is pressed, the controller is unlocked. The REAR button as well as the Rear indicator on screen will turn red. This indicates that you are now adjusting pressure of the rear air springs. Press REAR again to re-lock. Front & Rear When the FRONT & REAR buttons are pressed, the controller is unlocked. The FRONT and REAR buttons as well as the Front & Rear indicators on screen will turn red. This indicates that you are now adjusting the front and rear air spring pressures simultaneously. Press re-lock. & REAR again to Preset Saved 70 68 Front 14.0V 130 Psi 70 68 Rear 1 2 3 Preset Reached 70 68 Front 14.0V 130 Psi 70 68 Rear 1 2 3 Figure 10 Figure 11 Figure 12 Figure 13 Figure 14 Figure 15 REAR FRONT REAR FRONT REAR Front Right & Left Air Spring Adjustment When button is selected: Press up or down arrow to adjust pressure for the FRONT right or left air spring individually. Press up or down arrow to adjust pressure for the FRONT right and left air springs simultaneously. Presets Continued Rear Right & Left Air Spring Adjustment When REAR button is selected: Press up or down arrow to adjust pressure for the REAR right or left air spring individually. Press up or down arrow to adjust pressure for the REAR right and left air springs simultaneously. Front & Rear Air Spring Adjustment When & REAR buttons are selected: Press or to adjust pressure for both FRONT & REAR air springs simultaneously. 70 68 Front 14.0V 130 Psi 70 68 Rear Preset Saved 70 68 Front 14.0V 130 Psi 70 68 Rear PrPerseesteRt eFacilheedd 70 68 Front 14.0V 130 Psi 70 68 Rear 1 2 3 1 2 3 1 23 REAR REAR Pressure Preset Buttons The four buttons in this section of the controller all function as presets. 1, 2, and 3 can be defined by the user and the last button will always be the air out preset. The controller must be unlocked to use or to save any preset. 1 2 3 To unlock controller either FRONT or REAR button must be selected. or REAR Settings Menu 70 68 Front 14.0V 130 Psi 70 68 Rear 1 23 Saving Pressure Presets After making adjustments to reach your desired pressure settings, press and hold any of the 3 buttons for 5 seconds to save these settings as a preset. 1 2 3 Preset Saved will pop up in the top left corner of the screen indicating you have successfully saved a preset. R-ID: PRO000000 S-ID: PRO000000 PWD: 000000 1.1.01 Minimum tank pressure 110 PSI > Maximum tank pressure 130 PSI > Front weigth adjustment High load > 1 2 3 FRONT REAR Using A Pressure Preset Unlock controller. Select your desired preset. 1 23 Preset Reached will pop up in the top left corner of the screen indicating you have successfully reached your preset. Front weight adjustment High load > Rear weight adjustment Low load > Ignition off preset Off > Ignition on preset Off > 1 2 3 FRONT REAR FRONT REAR Air Out Unlock controller. Hold for 3 seconds to release ALL pressure from air springs. Button will illuminate red when fully aired out. Overwriting Pressure Presets If you would like to change an existing preset, simply set your desired pressures, then hold any of these 3 buttons for 5 seconds and your new preset will be set to the 1 2 3 given number. Preset Saved will pop up in the top left corner of the screen indicating you have successfully saved a new preset. FRONT REAR Failed Pressure Preset It is possible that your system will be unable to reach a pressure preset due to certain operating conditions, such as low air tank pressure. If this occurs, Preset Failed will pop-up in the topleft corner of the screen, indicating that the preset was not successfully reached. Ensure your air tank is at the maximum pressure before trying again. FRONT REAR Opening the Settings Menu Hold FRONT & REAR simultaneously for 3 seconds to enter the settings menu. FRONT REAR FRONT REAR Navigating The Settings Menu Press & to navigate through the settings menu. The selected option will be highlighted in white. Navigating Options Press & to scroll through the options for the current setting. The selected option will be highlighted in red. To adjust another setting, use the up & down arrows indicated in figure 14. Press REAR to exit Figure 16 Figure 17 Figure 18 Figure 19 Settings Menu Continued R-ID: PRO000000 S-ID: PRO000000 PWD: 000000 1.1.01 Minimum tank pressure 110 PSI > Maximum tank pressure 130 PSI> Front weight adjustment High load > 1 2 3 Front weight adjustment High load > Rear weight adjustment < Low load Ignition off preset Off > Ignition on preset Off > 1 2 3 Front weight adjustment High load > Rear weight adjustment < Low load Ignition off preset Preset 1 > Ignition on preset < Preset 2 > 1 23 FRONT REAR FRONT REAR FRONT REAR Minimum Tank Pressure Set a pressure for your compressor to TURN ON at. Selection range: 110-210 PSI *To raise minimum tank pressure, first increase the maximum. Maximum Tank Pressure Set a pressure for your compressor to TURN OFF at. Selection range: 130-230 PSI *Recommended operating tank pressure is 200PSI or less in order to be safe and compatible with all components. Wiring & Plumbing Diagram Front/Rear Weight Adjustment For the best results when trying to reach presets, we recommend testing both High load and Low load for the front and rear of your car. You may find that one setting improves your system's ability to consistently hit your desired height. NOTE: Vehicles with sleeve-style air springs will always benefit from being inflated ABOVE your preset, before pressing a given preset button. Ignition On/Off Presets If assigned, the system will automatically attempt to reach the selected preset when the vehicle's ignition is turned on, or off. Selection options: Preset 1-2-3-4 KEY: 1 2 3 Preset 1 Preset 2 Preset 3 Air Out (Preset 4) Mobile App/Connection R-ID: PRO000000 S-ID: PRO000000 PWD: 000000 1.1.01 Minimum tank pressure 110 PSI > Maximum tank pressure 130 PSI> Front weight adjustment High load > 1 2 3 Download on the App Store Bag Riders Pro Air Ride Control System Get Download on Google Play FRONT REAR Bag Riders Pro Air Ride Control System 4.0 Serial Numbers R-ID: PRO000000 Controller Bluetooth module serial number S-ID: PRO000000 Manifold serial number PWD: 000000 Remote control Bluetooth password Download App Scan the QR Code below to find app download links. Available for iOS and Android. App Pairing 1. When you use the app for the first time, the Bluetooth device list will pop up. Tap the Bluetooth device and select the serial number that matches your PRO Control System. This will be the R-ID serial number displayed on top left of the wired controller when the Settings Menu is open. (Figure 19) 2. Once you have selected the Bluetooth device, a password prompt will pop up. Enter your password to start using the app. The password (PWD) can be found on top left of the wired controller when the Settings Menu is open. (Figure 19) DIAGRAM KEY COMPONENTS WITHIN GREY BOXES ARE OPTIONAL ADDITIONS TO YOUR SYSTEM CONNECT TO CAR BATTERY POSITIVE [+] CONNECT TO CAR BATTERY NEGATIVE [-] 40 AMP FUSE 7.5 AMP FUSE 40 AMP FUSE COMPRESSOR PRE-WIRED RELAY VCC VCC 1/4" OR 3/8" NPT SWIVEL ELBOW 1/4" OR 3/8" PTC OPTIONAL SMC CHECK V A LV E 3/8" TO 1/4" NPT HEX NIPPLE AIR TANK HEX PLUG OPTIONAL SMC CHECK V A LV E 3/8" TO 1/4" NPT HEX NIPPLE AIR LINE AIR LINE AIR LINE S U P P LY L I N E AIR LINE OPTIONAL 1/4" WATER TRAP EXTERNAL DRAIN/FILL LINE AIR LINE AIR LINE AIR LINE AIR LINE AIR LINE AIR LINE SWIVEL ELBOW 1/4" NPT TO 1/4" PTC 1/4" PTC I N F L AT I O N V A LV E 70 68 Front 3.4V 130 Psi 70 68 Rear 1 23 REAR OPTIONAL 1/4" SECOND WATER TRAP MANIFOLD / ECU EXHAUST 1/4" G-THREAD SWIVEL ELBOW 1/4" OR 3/8" PTC MALE STRAIGHTS AIR LINE ATTACH TO CONTROLLER EXHAUST ALLEN PLUG 1/4" G-THREAD 1/4" OR 3/8" PTC 1/4" G-THREAD SWIVEL ELBOW 1/4" OR 3/8" PTC AIR LINE AIR LINE AIR LINE AIR LINE AIR LINE S E C O N D A RY S U P P LY L I N E AIR LINE AIR LINE AIR LINE AIR LINE AIR LINE AIR LINE 1/4" NPT SWIVEL ELBOW 1/4" OR 3/8" PTC SYSTEM WIRING HARNESS AIR LINE AIR LINE AIR LINE AIR LINE AIR LINE AIR LINE AIR LINE AIR LINE AIR LINE AIR LINE AIR LINE AIR LINE AIR LINE CONNECT TO IGNITION SOURCE POSITIVE [+] FUSE TAP 3 AMP FUSE IGN OPTIONAL SECOND PRE-WIRED RELAY SECOND PRE-WIRED RELAY Manifold / ECU Mounting 8 SECOND COMPRESSOR AIR LINE AIR LINE FRONT RIGHT AIR SPRING AIR LINE REAR RIGHT AIR SPRING OPTIONAL SECOND AIR COMPRESSOR AIR LINE AIR LINE REAR LEFT AIR LINE A I R S P R I N G AIR LINE AIR LINE AIR LINE 1/4" OR 3/8" AIR LINE FRONT LEFT AIR SPRING Mounting Instructions Mounting points are located at each corner of the underside of the manifold / ECU. Use these threaded holes to anchor your manifold to your mounting surface using the included hardware. If you require longer hardware (not included), the thread pitch of these holes is M4x0.7. In order to make mounting your manifold / ECU as straightforward as possible, we have created an easy-to-use, printable drilling template. Instructions for downloading the drill template are found to the right. Mounting Template Scan the QR to access the Bag Riders PRO Control System Manifold / ECU Mounting Template PDF. Print the PDF and follow the instructions to ensure proper mounting. V16Adobe PDF library 17.00 Adobe Illustrator 27.6 (Windows)