KRAMER AFM-20DSP-AEC 20-Port Audio Matrix Cov Lus Qhia

AFM-20DSP-AEC Quick Start Guide

https://de2gu.app.goo.gl/eibH3igKhyjKxEjy5

This guide helps you install and use your AFM-20DSP-AEC for the first time.
mus rau www.kramerav.com/downloads/AFM-20DSP-AEC txhawm rau rub tawm cov neeg siv phau ntawv siv kawg thiab txheeb xyuas yog tias firmware hloov kho dua tshiab.

Kauj ruam 1: Khij dab tsi hauv lub thawv

1. AFM-20DSP-AEC 20 Port Audio Matrix
2. 1 Lub hwj chim qaum
3. 1 Teeb ntawm pob ntseg pob ntseg
4. 4 Roj Hmab Ntiv Taw
5. 1 Quick Start guide

Step 2: Get to know your AFM-20DSP-AEC

#	feature		muaj nuj nqi
1	STATUS LED		Indicates the system’s status: •3 cycles of red/blue/off/green LEDs • Flashes green when the application starts. that flash in sequence for 30 seconds • Stays green when system is ready for use. when the system starts up, and the application has not been launched.
2	PORTS LEDs (1 to 20)		Indicate the port’s status: •Green when an input signal is • Red when in clipping state. detected, and the port is defined as • Yellow when in limiting state. line in. •Off when there is no signal on the input. •White when defined as line out. •Blue when defined as mic in.
3	IN OUT Dante TM LEDs (1 to 4)		Indicate the Dante’s signal status: •Green when a signal is detected. • Yellow when in limiting state. •Red when clipping occurs. • Off when no signal is detected.
4	HDMI LEDs	EMBED	Turns green when an analog audio signal is associated with the HDMI OUT signal. Otherwise, it stays OFF.
		DE-EMBED	Turns green when the HDMI IN audio signal is detected. Otherwise, it stays OFF.
5	IN OUT USB or S/PDIF LEDs		Indicate the USB or S/PDIF’s status: •Green when a signal is detected. • Off when no signal is detected. If a signal is detected on one channel, either left only or right only, the status LED is green.
6	CH 1(L)/CH 2(R) AMPLIFIER LEDs		Qhia tus amplifier’s signal status: •Green when a signal is detected. • Off when no signal is detected. Nyob rau web page, CH1 and CH2 are referred to as AMP 1 thiab AMP 2, muaj feem.

#	feature	muaj nuj nqi
7	PORTS 3-pin Terminal Block Connectors (1 to 20)	Interchangeable balanced mono-audio ports. Connect to an audio source or acceptor in 1 of 8 selectable I/O configurations: 16×4, 14×6, 12×8, 12×8 AEC ,10×10, 8×12, 6×14, 4×16. Define each port as line in, mic in, mic + 48V in, or line out.
8	USB	AFM-20DSP-AEC can process the USB audio as a stereo speaker or operate as an audio line-in or microphone for an audio recorder application or call conferencing. When the AFM-20DSP-AEC is connected to a computer via USB-B: •In the computer’s Settings > Manage sound devices > Output devices, the AFM20DSP-AEC USB shows as “Speaker USB AUDIO CODEC”. •In a computer recoding application, the audio input settings for AFM-20DSP-AEC show as ‘tine USB AUDIO CODEC”. Tseem ceeb: •The computer’s “Output” device (such as speakers) shows in the AFM-20DSP-AEC embedded web pages as a USB Digital “Input”. •The computer’s “Input” device (such as a microphone) shows in the AFM-20DSPAEC embedded web pages as a USB Digital “Output”.
9	HDMI OUT Connector	Connect to an HDMI acceptor to embed an audio signal from the matrix.
10	HDMI hauv Connector	Connect to an HDMI source to de-embed the audio signal (the video signal is passed through to the output).
11	S/PDIF OUT RCA Connector	Connect to a digital stereo audio acceptor.
12	S/PDIF IN RCA Connector	Connect to a digital stereo audio source.
13	Hais lus tawm	Outputs two selected audio signals in two channels. •For Lo-Z: connect stereo output to Lo-Z speakers: L+ and L- to the left speaker; R+R- to the right speaker. •For Hi-Z (70V or 100V): connect Hi-Z and COM to mono Hi-Z speakers.
14	Dante PoE RJ-45 Port	Connect to Dante audio through the network. Provides 4 Tx channels and 4 Rx channels. By default, DHCP is enabled.
15	RS-232 3-pin Terminal Thaiv Connector	Txuas mus rau lub PC/cov tswj hwm los tswj lub cuab yeej.
16	ETHERNET RJ-45 Txuas	Connect to a PC via a LAN to control the device and for firmware upgrades.
17	Micro USB PROG. PORT	Connect to your PC to control the device.
18	RESET khawm Recessed	Press and hold for 5 seconds, to reset the configuration to its default parameters.
19	Mains Power Connector and Fuse	Plug in for the power cord.
20	POWER Illuminated Power Switch	Nws qhib thiab kaw lub cuab yeej.

Step 3: Mount AFM-20DSP-AEC

To rack mount the machine, attach both rack ears (remove the screws from each side of the machine and replace screws through the rack ears) or place the machine on a table.

• Ensure that the environment (e.g., maximum ambient temperature & airflow) is compatible for the device.
• Zam kev thauj khoom tsis sib xws.
• Kev txiav txim siab tsim nyog ntawm cov khoom siv npe npe yuav tsum tau siv kom tsis txhob muaj overloading ntawm circuits.
• Lub pob ntseg txhim khu kev qha ntawm cov khoom siv sib dhos yuav tsum tswj xyuas.

Kauj Ruam 4: Txuas cov kev tawm tswv yim thiab cov tawm

Always turn off the power on each device before it is connected to the AFM-20DSP-AEC device.

For optimum range and performance, use the recommended Kramer cables available at
www.kramerav.com/product/AFM-20DSP-AEC. The use of third-party cables may cause damage!

Kauj Ruam 5: Txuas lub hwj chim

Connect the power cord to AFM-20DSP-AEC and plug it into the mains electricity.
Cov Lus Qhia Kev Nyab Xeeb (Saib www.kramerav.com rau cov ntaub ntawv tshiab txog kev nyab xeeb)
Ceeb toom:

• Tsis muaj cov tswj hwm kev pabcuam hauv cov chav ua haujlwm.

Ceeb toom:

• Siv cov hlua hluav taws xob tsuas yog tau txuas nrog chav ntsuas.
• Txuas lub hwj huam thiab tshem tawm ntawm chav tsev ntawm phab ntsa ua ntej nruab.
• Tsis txhob qhib chav nyob. Siab heevtages tuaj yeem ua rau hluav taws xob poob siab! Kev pabcuam los ntawm cov neeg ua haujlwm tsim nyog nkaus xwb.
• To ensure continuous risk protection, replace fuses only according to the rating specified on the product label is located on the bottom of the unit.

Step 6: Operate AFM-20DSP-AEC

To operate AFM-20DSP-AEC, use:

• embedded web nplooj ntawv ntawm Ethernet.
• RS-232 serial commands are transmitted by a touch screen system, PC, or another serial controller.

Tus nqi Baud:	115,200	Parity:	tsis muaj leej twg
Cov ntaub ntawv khoom:	8	Hais Hom Ntawv:	ASCII
Cov khoom nres:	1
Example: (adjust the amplified audio from analog audio 1 to -10dB): #x-aud-lvl out.amplified_audio.1.audio.1,-10
Default Ethernet Parameters
Tus IP Chaw Nyob:	192.168.1.39	UDP Chaw nres nkoj #:	50000
Subnet Mask:	255.255.0.0	TCP Chaw nres nkoj #:	5000
Rooj vag:	192.168.0.1	Tus username/password	Tsev/Admin
Cov Hoobkas Rov Tuaj
Recessed Khawm	default parameters.
Raws tu qauv 3000:	"#Factory" hais kom ua.
Web Nplooj ntawv:	In the Settings page, click Factory Reset.

www.KRAMERAV.com

Cov ntaub ntawv / Cov ntaub ntawv

KRAMER AFM-20DSP-AEC 20-Port Audio Matrix [pdf] Daim Ntawv Qhia Tus Neeg Siv AFM-20DSP-AEC 20 Port Audio Matrix, AFM-20DSP-AEC, 20 Port Audio Matrix