Daim ntawv

HUNTER-LOGO

HUNTER 19438 Klein 1 Light Glass Pendant

HUNTER-19438 -Klein-1-Light-Glass-Pendant-product

tshajview

HUNTER-19438 -Klein-1-Light-Glass-Pendant-fig-1

COV LUS QHIA INSTALLATION

CEEB TOOM 

  • To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location
  • Lub teeb siv hluav taws xob yuav tsum yog av. Yog tias cov hlau hluav taws xob rau lub chaw teeb tsa tsis nyob, tam sim ntawd TSUM txoj kev teeb tsa thiab sab laj tus kws siv hluav taws xob tsim nyog.
  • Txhua qhov kev xaim yuav tsum yog ua raws li lub teb chaws thiab cheeb tsam hluav taws xob cov lej ANSI / NFPA 70. Yog tias koj tsis paub nrog cov xaim hluav taws xob lossis tsis paub tseeb, sab laj hluav taws xob tsim nyog.

NYEEM THIAB SAIB COV LUS QHIA NO
Cov lus qhia no tau muab rau koj kev nyab xeeb. Nws yog ib qho tseem ceeb heev uas lawv yuav tsum tau nyeem kom zoo thiab tag nrho ua ntej pib lub installation ntawm lub teeb pom kev zoo fixture.

Ntawm no yog cov cuab yeej koj yuav tsum tau ua kom tiav koj lub installation

HUNTER-19438 -Klein-1-Light-Glass-Pendant-fig-3

NPAJ RAU INSTALLATION

Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture. Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. One end of the threaded post (H) should be attached to the mounting bracket (A) with a hex nut (G) in place. The other end should be connected to the canopy loop (E). Unscrew the canopy loop ring (F) from the canopy loop (E). Depending on the placement of your junction box the position of the threaded post (H) may need to be adjusted to allow the canopy to be flush with the ceiling. Determine this by lifting mounting bracket (A) up to the junction box and placing canopy (D) over the canopy loop (E), so that it is flush with the ceiling. Adjust the position of the threaded post (H) on the mounting bracket (A) so that the canopy (D) covers at least half of the exterior threads on the canopy loop  (E) while it is securely connected to the threaded post (H). The threaded post (H) can be adjusted by loosening the hex nut (G) to allow movement of the threaded post (H) on the mounting bracket (A). Once the ideal position of the threaded post (H) is determined, tighten up the hex nut (G) onto the threaded post (H) just beneath the mounting bracket (A) to secure the threaded post in place..

SIB DHOS RAU TUS NEEG PHEM

There are 4 12-inch rods (I), and 1 6-inch rod (J) included for each fixture. Determine the correct number of rods needed for proper hanging height. To lengthen the fixture, add additional rods. To shorten the fixture, trim the wires to the desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the fixture’s wiring to discard. Keep in mind that you must use at least one rod to hang the fixture. Thread the wires through the rods and pull the wires until taut before connecting the rods together. Screw rod onto threaded post (K) on the fixture. Pull the fixture wires through the canopy loop ring (F), top of the canopy (D), and canopy loop (E). Screw the top rod to the canopy loop (E). Have a helper support the fixture’s weight and attach the mounting bracket (A) to the junction box by securely tightening the mounting screws (B).

HUNTER-19438 -Klein-1-Light-Glass-Pendant-fig-2

CONNECTING COV PHEEJ 
Txuas lub fixture cov xov hlau mus rau lub hwj huam mov xaim los ntawm lub thawv sib txuas. Txuas dub rau dub (Live); dawb mus rau dawb (grounded); grounding rau grounding (ntsuab los yog tooj liab). Twist qhov kawg ntawm cov hlau ua ke. Tom qab ntawd, twist ntawm ib tug hlau connector. Xyuas kom tag nrho cov twists nyob rau hauv tib txoj kev. Loop fixture lub hauv av xaim nyob ib ncig ntawm grounding ntsia hlau (C) thiab ceev. Yog tias tsis muaj cov xaim hauv av (ntsuab lossis tooj liab) los ntawm lub thawv sib txuas, hu rau tus kws tshaj lij hluav taws xob tsim nyog

XOV XWM TXOG TXIM

Muab lub qhov (D) ntws mus rau lub qab nthab thiab xaub lub voj voos (F) nyob rau hauv qab lub canopy. Tightly ntsia hlau canopy voj nplhaib (F) mus rau lub canopy voj (E) kom ruaj ntseg canopy (D) nyob rau hauv qhov chaw. Ua tib zoo nruab iav ntxoov ntxoo (M) hla lub qhov (socket) (L), tom qab ntawd nruab lub qhov (socket) npog (N) thiab tuav lub iav ntxoov ntxoo nrog lub nplhaib (O). Nruab qhov muag teeb (tsis suav nrog) raws li cov khoom siv tshwj xeeb. Tsis txhob tshaj qhov pom zoo wattage. Tam sim no koj lub installation tiav lawm. Tig lub hwj chim thiab sim lub fixture.

TU COV TSWV YIM

Kho lub fixture maj mam muab! Kev tu kom tsis tu ncua yuav txo qhov xav tau kev tu kom huv. Rau kev tu kom tsis tu ncua, tua lub teeb thiab so lub fixture nrog ib daim ntaub dawb huv-lossis paj rwb microfiber. Tsis txhob muab tshuaj tsuag rau qhov chaw nyob ntawd kiag li.

TSAB NTAWV CEEB TOOM
In order to use a 12-in rod by itself, you must first remove the post from the 6-in rod and install it on one of the ends of the 12-in rod

Hunter Pro Tswv Yim 
Twist or tape wire ends together to make it easier to pass them through the down rods. Threaded posts may also be removed for easier wire access

Cov ntaub ntawv / Cov ntaub ntawv

HUNTER 19438 Klein 1 Light Glass Pendant [pdf] Owner's Manual
19438, 19439, Glass Pendant, Pendant

Cia ib saib

Koj email chaw nyob yuav tsis tsum luam tawm.