Hatco-logo

Hatco GRBW Series GLO-RAY Buffet Warmers

Hatco-GRBW-Series-GLO-RAY-Buffet-Warmers-product

CEEB TOOM
Do not operate this equipment unless you have read and understood the contents of this manual! Failure to follow the instructions contained in this manual may result in serious injury or death. This manual contains important safety information concerning the maintenance, use, and operation of this product. If you’re unable to understand the contents of this manual, please bring it to the attention of your supervisor. Keep this manual in a safe location for future reference. English = p 2.

COV NTAUB NTAWV TSEEM CEEB

Sau tus qauv naj npawb, serial tooj, voltage, and purchase date of the unit in the spaces below (specification label located on the front of the unit). Please have this information available when calling Hatco for service assistance.

  • Model Tsis. _______________________________________
  • Tsis tau. ________________________________________
  • Voltage __________________________________________
  • Hnub Yuav Khoom __________________________________

Sau npe koj lub tsev!
Completing online warranty registration will prevent delays in obtaining warranty coverage. Access the Hatco website ntawm www.hatcocorp.com, xaiv cov ntawv qhia txhawb nqa rub-down, thiab nyem rau ntawm "Warranty".

Sijhawm Ua Lag Luam:
7:00 AM to 5:00 PM Monday–Friday, Central Time (CT) (Summer Hours: June to September— AM7:00 to 5:00 PM Monday–Thursday AM7:00 to 4:00 PM Friday).

24-Hour 7-Day Parts and Service Assistance is available in the United States and Canada by calling 800-558-0607. Additional information can be found by visiting our website nyob www.hatcocorp.com.

TAW qHIA

Hatco Glo-Rite® Display Lights are durable and effective light strips ideal for use in food preparation, holding and display areas. The lights are made of extruded aluminum housings with bright annealed reflectors for maximum brightness and feature shatter-resistant incandescent lights. Each unit comes equipped for mounting and electrical hook-up along with a Power I/O (on/off) switch for operator control.

Hatco Display Lights are products of extensive research and field testing. The materials used were selected for maximum durability, attractive appearance, and optimum performance. Every unit is inspected and tested thoroughly prior to shipment. This manual provides the installation, safety, and operating instructions for Display Lights. Hatco recommends all installation, operating, and safety instructions appearing in this manual be read prior to installation or operation of a unit.

Cov ntaub ntawv kev nyab xeeb uas tshwm sim hauv phau ntawv no tau txheeb xyuas los ntawm cov lus qhia hauv qab no:

  • CEEB TOOM qhia txog qhov xwm txheej txaus ntshai uas, yog tias tsis zam, tuaj yeem ua rau tuag lossis raug mob hnyav.
  • CEEV FAJ qhia txog qhov xwm txheej txaus ntshai uas, yog tias tsis zam, tuaj yeem ua rau raug mob me lossis nruab nrab.
  • TSAB NTAWV CEEB TOOM yog siv los hais txog kev coj ua tsis cuam tshuam txog kev raug mob ntawm tus kheej.

LUS QHIA TSEEM CEEB HEEV

Nyeem cov ntaub ntawv kev nyab xeeb tseem ceeb hauv qab no ua ntej siv cov cuab yeej no kom tsis txhob raug mob hnyav lossis tuag thiab kom tsis txhob muaj kev puas tsuaj rau cov khoom siv lossis khoom.

CEEB TOOM

ELECTRIC SHOCK HAZARD:

  • The unit must be installed by a qualified electrician. Installation must conform to all local electrical codes. Installation by unqualified personnel will void unit warranty and may lead to electric shock or burn, as well as damage to the unit and/or its surroundings.
  • Consult a licensed electrical contractor for proper electrical installation conforming to local electrical codes and the National Electrical Code (N.E.C.).
  • Turn OFF the power at the fused disconnect switch/circuit breaker and allow the unit to cool before performing any cleaning, adjustments, or maintenance.
  • DO NOT submerge or saturate with water. The unit is not waterproof. Do not operate if the unit has been submerged or saturated with water.
  • Tsis txhob ntxuav lub tsev thaum nws muaj zog lossis kub.
  • The unit is not weatherproof. Locate the unit indoors where the ambient air temperature is a minimum of 70°F (21°C).
  • Tsis txhob ua kom huv si lossis siv dej ntau dhau ntawm chav tsev.
  • This unit is not “jet-proof” construction. Do not use a jet-clean spray to clean this unit.
  • Chav tsev no yuav tsum tau muab kev pabcuam los ntawm cov neeg ua haujlwm tsim nyog nkaus xwb. Kev pabcuam los ntawm cov neeg ua haujlwm tsis tsim nyog yuav ua rau hluav taws xob poob lossis hlawv.
  • Siv cov Hatco Hloov Qhov Tseeb tsuas yog thaum xav tau kev pabcuam. Kev tsis siv Cov Hatco Hloov Qhov Tseeb yuav ua rau tag nrho cov kev lav phib xaub thiab tej zaum yuav raug cov neeg ua haujlwm ntawm cov cuab yeej ua rau muaj teeb meem hluav taws xob vol.tage, ua rau hluav taws xob poob lossis hlawv. Hatco Qhov Chaw Hloov Kho Qhov Tseeb tau teev tseg kom ua haujlwm nyab xeeb hauv ib puag ncig uas lawv tau siv. Qee qhov chaw tom qab lossis cov khoom hloov pauv tsis muaj cov yam ntxwv uas yuav ua rau lawv ua haujlwm zoo hauv Hatco cov cuab yeej.

HLUAV TAWS KUB:

  • Locate the unit at the correct distance from combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur.
  • Make sure food product has been heated to the proper food-safe temperature before placing them on the unit. Failure to heat food products properly may result in serious health risks. This unit is for holding preheated food products only.
  • Xyuas kom txhua tus neeg ua haujlwm tau qhia txog kev nyab xeeb thiab siv tau zoo ntawm chav tsev.
  • Chav tsev no tsis yog tsim los siv los ntawm cov menyuam yaus lossis cov neeg uas muaj peev xwm txo lub cev, hnov ​​​​lus, lossis lub hlwb. Xyuas kom cov menyuam saib xyuas kom raug thiab kom lawv nyob deb ntawm chav tsev.

CEEB TOOM

  • ZOO TSHAJ PLAWS: Tsis txhob tso roj lossis siv roj av lossis lwm yam khoom siv hluav taws xob lossis kua dej nyob ib puag ncig qhov no lossis lwm yam khoom siv.
  • Xyuas kom txhua tus neeg ua haujlwm tau qhia txog kev nyab xeeb thiab siv tau zoo ntawm chav tsev.
  • Chav tsev no tsis yog tsim los siv los ntawm cov menyuam yaus lossis cov neeg uas muaj peev xwm txo lub cev, hnov ​​​​lus, lossis lub hlwb. Xyuas kom cov menyuam saib xyuas kom raug thiab kom lawv nyob deb ntawm chav tsev.
  • Use only light bulbs that meet or exceed National Sanitation Foundation (NSF) standards and are specifically designed for food-holding areas. Breakage of light bulbs not specially-coated could result in personal injury and/or food contamination.
  • Chav tsev no tsis muaj "neeg siv-kev pabcuam" qhov chaw. Yog xav tau kev pab cuam ntawm chav tsev no, hu rau Tus Neeg Saib Xyuas Kev Tso Cai Hatco lossis hu rau Hatco Service Department ntawm 800-558-0607 lossis 414-671-6350.

CEEV FAJ
Standard and approved manufacturing oils may smoke up to 30 minutes during initial startup. This is a temporary condition. Operate unit without food product until the smoke dissipates.

TSAB NTAWV CEEB TOOM
Tsuas yog siv cov tshuaj ntxuav thiab cov ntaub uas tsis yog abrasive. Abrasive cleaners thiab ntaub yuav khawb qhov kawg ntawm chav tsev, marring nws cov tsos thiab ua rau nws raug rau cov av nkos.

Qauv DESCRIPTION

Tag nrho cov qauv
Hatco Glo-Ray® Buffet Warmers are ideal for holding hot food on a buffet line or temporary serving areas. The GRBW models are available in various widths from 25-1/8″ to 73-1/8″ (638 to 1857 mm). a metal-sheathed heating element directs heat from above while below the thermostatically-controlled heated base conducts heat from 80°–180°F (27°–82°C).

Standard features include stainless steel top surface, sturdy plastic sneeze guards, shatter-resistant incandescent display lighting, and a 6′ (1829 mm) cord and plug set.
Optional features available include plastic side panels, a plastic front enclosure, sign holders, 9-3/8″ (238 mm) or 14″ (356 mm) sneeze guards, a hard-coated base, overhead heat controls (GRBW-24 through GRBW-60 models only), Designer colors, and halogen display light bulbs. Pan Rails and 4″ (102 mm) adjustable legs are available as accessories.

CEEB TOOM: Refer to the OPTIONS AND ACCESSORIES section for additional information.Hatco-GRBW-Series-GLO-RAY-Buffet-Warmers-fig-1

Qauv DESIGNATIONHatco-GRBW-Series-GLO-RAY-Buffet-Warmers-fig-2

specifications

Plug Configurations
Cov chav nyob yog muab los ntawm lub Hoobkas nrog rau cov hlua hluav taws xob thiab ntsaws ntsaws. Plugs yog muab los ntawm cov ntawv thov.

CEEB TOOM
ELECTRIC SHOCK HAzARD: Plug unit into a properly grounded electrical receptacle of the correct voltage, loj, thiab ntsaws configuration. Yog tias lub ntsaws thiab lub thawv ntim tsis sib xws, hu rau tus kws tshaj lij hluav taws xob tsim nyog los txiav txim siab thiab nruab qhov tsim nyog voltage thiab loj hluav taws xob txais.

  • CEEB TOOM: The specification label is located on the top rear of the unit. See label for serial number and verification of unit electrical information.
  • CEEB TOOM: Receptacle tsis muab los ntawm Hatco.Hatco-GRBW-Series-GLO-RAY-Buffet-Warmers-fig-3
Electrical Rating Chart — GRBW-24–GRBW-36
qauv Voltage watts Amps Plug configuration Shipping Nyhav
GRBW-24 100 934 9.3 NEma 5-15P 48 lbs. (22 kg)
120 970 8.1 NEma 5-15P 48 lbs. (22 kg)
120 / 208 970 4.2 NEma L14-20P 48 lbs. (22 kg)
120 / 240 970 4.2 NEma L14-20P 48 lbs. (22 kg)
220 920 4.2 CEE 7/7 Schuko 48 lbs. (22 kg)
240

220–230 (CE)

1000

920-1006

4.2

4.2-4.4

BS-1363

CEE 7/7 Schuko

48 lbs. (22 kg)

48 lbs. (22 kg)

230–240 (CE) 918-1000 4.0-4.2 BS-1363 48 lbs. (22 kg)
GRBW-30 100 1194 11.9 NEma 5-15P 52 lbs. (24 kg)
120 1230 10.3 NEma 5-15P 52 lbs. (24 kg)
120 / 208 1230 5.5 NEma L14-20P 52 lbs. (24 kg)
120 / 240 1230 5.5 NEma L14-20P 52 lbs. (24 kg)
220 1172 5.3 CEE 7/7 Schuko 52 lbs. (24 kg)
240 1270 5.3 BS-1363 52 lbs. (24 kg)
220–230 (CE) 1172-1281 5.3-5.6 CEE 7/7 Schuko 52 lbs. (24 kg)
230–240 (CE) 1166-1270 5.1-5.3 BS-1363 52 lbs. (24 kg)
GRBW-36 100 1476 14.8 NEma 5-15P 58 lbs. (26 kg)
120 1530 12.8 NEma 5-15P* 58 lbs. (26 kg)
120 / 208 1530 6.7 NEma L14-20P 58 lbs. (26 kg)
120 / 240 1530 6.7 NEma L14-20P 58 lbs. (26 kg)
220 1454 6.6 CEE 7/7 Schuko 58 lbs. (26 kg)
240 1578 6.6 BS-1363 58 lbs. (26 kg)
220–230 (CE) 1454-1589 6.6-6.9 CEE 7/7 Schuko 58 lbs. (26 kg)
230–240 (CE) 1449-1578 6.3-6.6 BS-1363 58 lbs. (26 kg)
GRBW-42 120 1730 14.4 NEma 5-15P* 68 lbs. (31 kg)
120 / 208 1730 7.9 NEma L14-20P 68 lbs. (31 kg)
120 / 240 1730 7.9 NEma L14-20P 68 lbs. (31 kg)
220 1648 7.5 CEE 7/7 Schuko 68 lbs. (31 kg)
240 1782 7.4 BS-1363 68 lbs. (31 kg)
220–230 (CE) 1648-1801 7.5-7.8 CEE 7/7 Schuko 68 lbs. (31 kg)
230–240 (CE) 1636-1782 7.1-7.4 BS-1363 68 lbs. (31 kg)
GRBW-48 120 2040 17.0 NEma 5-20P† 74 lbs. (34 kg)
120 / 208 2040 9.2 NEma L14-20P 74 lbs. (34 kg)
120 / 240 2040 9.2 NEma L14-20P 74 lbs. (34 kg)
220 1940 8.8 CEE 7/7 Schuko 74 lbs. (34 kg)
240 2040 8.5 BS-1363 74 lbs. (34 kg)
220–230 (CE) 1940-2120 8.8-9.2 CEE 7/7 Schuko 74 lbs. (34 kg)
230–240 (CE) 1875-2040 8.1-8.5 BS-1363 74 lbs. (34 kg)

Cov chaw ntxoov ntxoo muaj cov ntaub ntawv hluav taws xob rau International qauv nkaus xwb.

  • NEma 5-20P for Canada.
  • Not available in Canada.
Electrical Rating Chart — GRBW-42–GRBW-72
qauv Voltage watts Amps Plug configuration Shipping Nyhav
GRBW-54 120 / 208 2290 10.4 NEma L14-20P 81 lbs. (37 kg)
120 / 240 2290 10.4 NEma L14-20P 81 lbs. (37 kg)
220 2182 9.9 CEE 7/7 Schuko 81 lbs. (37 kg)
240 2360 9.8 BS-1363 81 lbs. (37 kg)
220–230 (CE) 2182-2385 9.9-10.4 CEE 7/7 Schuko 81 lbs. (37 kg)
230–240 (CE) 2167-2360 9.4-9.8 BS-1363 81 lbs. (37 kg)
GRBW-60 120 / 208 2600 11.7 NEma L14-20P 90 lbs. (41 kg)
120 / 240 2600 11.7 NEma L14-20P 90 lbs. (41 kg)
220 2474 11.2 CEE 7/7 Schuko 90 lbs. (41 kg)
240 2680 11.2 BS-1363 90 lbs. (41 kg)
220–230 (CE) 2474-2704 11.2-11.8 CEE 7/7 Schuko 90 lbs. (41 kg)
230–240 (CE) 2470-2680 10.7-11.2 BS-1363 90 lbs. (41 kg)
GRBW-66 120 / 208 2860 13.0 NEma L14-20P 96 lbs. (44 kg)
120 / 240 2860 13.0 NEma L14-20P 96 lbs. (44 kg)
220 2726 12.4 CEE 7/7 Schuko 96 lbs. (44 kg)
240 2948 12.3 BS-1363 96 lbs. (44 kg)
220–230 (CE) 2726-2978 12.4-12.9 CEE 7/7 Schuko 96 lbs. (44 kg)
230–240 (CE) 2707-2948 11.8-12.3 BS-1363 96 lbs. (44 kg)
GRBW-72 120 / 208 3125 14.4 NEma L14-20P 107 lbs. (49 kg)
120 / 240 3125 14.4 NEma L14-20P 107 lbs. (49 kg)
220 2983 13.6 CEE 7/7 Schuko 107 lbs. (49 kg)
240 3113 13.0 BS-1363 107 lbs. (49 kg)
220–230 (CE) 2983-3260 13.6-14.2 CEE 7/7 Schuko 107 lbs. (49 kg)
230–240 (CE) 2859-3113 12.4-13.0 BS-1363 107 lbs. (49 kg)

Cov chaw ntxoov ntxoo muaj cov ntaub ntawv hluav taws xob rau International qauv nkaus xwb.

Qhov ntev
qauv dav (A) qhov tob (B) Qhov siab (C) qhov tob (D) Hneev taw dav (E) Hneev taw qhov tob (F)
GRBW-24 ‡ 25-1 / 8 ″ (638 hli) 22-1 / 2 ″ (572 hli) 17-3 / 4 ″ (451 hli) 19-1 / 2 ″ (495 hli) 22-5 / 8 ″ (575 hli) 17-15 / 16 ″ (456 hli)
GRBW-30 ‡ 31-1 / 8 ″ (791 hli) 22-1 / 2 ″ (572 hli) 17-3 / 4 ″ (451 hli) 19-1 / 2 ″ (495 hli) 28-5 / 8 ″ (727 hli) 17-15 / 16 ″ (456 hli)
GRBW-36 ‡ 37-1 / 8 ″ (943 hli) 22-1 / 2 ″ (572 hli) 17-3 / 4 ″ (451 hli) 19-1 / 2 ″ (495 hli) 34-5 / 8 ″ (879 hli) 17-15 / 16 ″ (456 hli)
GRBW-42 43-1 / 8 ″ (1095 hli) 22-1 / 2 ″ (572 hli) 20-3 / 4 ″ (527 hli) 19-1 / 2 ″ (495 hli) 40-5 / 8 ″ (1032 hli) 17-15 / 16 ″ (456 hli)
GRBW-48 49-1 / 8 ″ (1248 hli) 22-1 / 2 ″ (572 hli) 20-3 / 4 ″ (527 hli) 19-1 / 2 ″ (495 hli) 46-5 / 8 ″ (1184 hli) 17-15 / 16 ″ (456 hli)
GRBW-54 55-1 / 8 ″ (1400 hli) 22-1 / 2 ″ (572 hli) 20-3 / 4 ″ (527 hli) 19-1 / 2 ″ (495 hli) 52-5 / 8 ″ (1337 hli) 17-15 / 16 ″ (456 hli)
GRBW-60 61-1 / 8 ″ (1553 hli) 22-1 / 2 ″ (572 hli) 20-3 / 4 ″ (527 hli) 19-1 / 2 ″ (495 hli) 58-5 / 8 ″ (1489 hli) 17-15 / 16 ″ (456 hli)
GRBW-66 67-1 / 8 ″ (1705 hli) 22-1 / 2 ″ (572 hli) 20-3 / 4 ″ (527 hli) 19-1 / 2 ″ (495 hli) 64-5 / 8 ″ (1641 hli) 17-15 / 16 ″ (456 hli)
GRBW-72 73-1 / 8 ″ (1857 hli) 22-1 / 2 ″ (572 hli) 20-3 / 4 ″ (527 hli) 19-1 / 2 ″ (495 hli) 70-5 / 8 ″ (1794 hli) 17-15 / 16 ″ (456 hli)

Standard units are equipped with 1” (25 mm) feet, add 3” (76 mm) to Height (C) when equipped with 4” (102 mm) legs.

CEEB TOOM: Depth (B) is for units equipped with the standard 7-1/2” (191 mm) sneeze guard.Hatco-GRBW-Series-GLO-RAY-Buffet-Warmers-fig-4

INSTALLATION

General
Glo-Ray® Buffet Warmers are shipped with most components pre-assembled. Care should be taken when unpacking shipping carton to avoid damage to unit and components enclosed.

CEEB TOOM

  • ELECTRIC SHOCK HAzARD: unit is not weatherproof. Locate unit indoors where the ambient air temperature is a minimum of 70°F (21°C).
  • FIRE HAzARD: Locate unit a minimum of 1″ (25 mm) from combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur.

CEEV FAJ

  • Locate unit at the proper counter height in an area that is convenient for use. The location should be level to prevent the unit or its contents from falling accidentally and strong enough to support the weight of the unit and contents.
  • Lub National Sanitation Foundation (NSF) xav kom cov chav nyob ntau dua 36 "(914 mm) hauv qhov dav lossis hnyav dua 80 lbs. (36 kg) yog muab kaw rau los yog tsa saum npoo ntawm lub installation. Yog tias chav tsev tsis tuaj yeem raug kaw ntawm qhov chaw siv, 4 "(102 mm) ob txhais ceg raug tso cai rau kev tu kom zoo hauv qab chav tsev.
  • Transport unit in upright position only. Failure to do so may result in damage to unit or personal injury.

TSAB NTAWV CEEB TOOM
Do not drag or slide unit when moving or installing. Carefully lift unit to prevent the rubber feet from tearing off.

  1. Tshem cov chav tsev hauv lub thawv.
    CEEB TOOM: To prevent delay in obtaining warranty coverage, complete online warranty registration. See the ImPORTaNT OWNER INFORmaTION section for details.
  2. Tshem cov ntaub nplaum thiab cov ntaub thaiv npog los ntawm txhua qhov chaw ntawm chav tsev.
  3. Install the sneeze guards. Refer to the “Installing the Sneeze Guard” procedure in this section.
  4. Place the unit in the desired location. Two people are required for this step.
    • Locate the unit in an area where the ambient air temperature is constant and a minimum of 70°F (21°C). avoid areas that may be subject to active air movements or currents (i.e., near exhaust fans/hoods, exterior doors, and air conditioning ducts).
    • make sure the unit is at the proper counter height in an area convenient for use.
    • make sure the countertop is level and strong enough to support the weight of the unit and food product.

CEEB TOOM: Refer to the OPTIONS AND ACCESSORIES section for additional installation information.

Installing the Sneeze Guard
all models are shipped with sneeze guards. Use the following procedure to install sneeze guards on the unit.

  1. assemble each weld screw through the top of the sneeze guard and through the support trim. Loosely thread a cap nut onto each of the weld screws below the support trim.
  2. Lift the sneeze guard assembly and carefully slide each of the weld screws that are loosely attached to the sneeze guard into the T-slot.
  3. align each end of the sneeze guard with the ends of the unit and then tighten the cap nuts to secure the sneeze guard in position. Do not over-tighten the cap nuts.Hatco-GRBW-Series-GLO-RAY-Buffet-Warmers-fig-5

General
Use the following procedures to operate Glo-Ray Buffet Warmers.

CEEB TOOM
Nyeem tag nrho cov lus hais txog kev nyab xeeb nyob rau hauv nqe lus tseem ceeb SAFETY INFORMATION ua ntej siv cov cuab yeej no.

  1. Txuas lub tsev rau hauv qhov chaw txais hluav taws xob hauv av kom raug ntawm qhov raug voltage, size and plug configuration. See the SPECIFICaTIONS section for details.
  2. move the Power ON/OFF (I/O) toggle switch to the ON (I) position.
    • The base blanket heating elements and the overhead heating elements will energize.
    • The display lights will turn on.
      CEEB TOOM: If the unit is equipped with optional top heat control, then the top heat control will control the overhead heating elements. The Power ON/OFF (I/O) toggle switch will control the base blanket heating elements and the display lights only.
  3. Turn the base heat control to the desired setting between LOW and HIGH. The base temperature range is approximately from 80°–180°F (27°–82°C).
  4. Turn the optional top heat control (if equipped) to the desired setting.

Shutdown

  1. move the Power ON/OFF (I/O) toggle switch to the OFF (O) position. all the heating elements and the display lights will shut off.
  2. If the unit is equipped with the optional top heat control, turn the top heat control to the OFF position. The overhead heating elements will shut off.Hatco-GRBW-Series-GLO-RAY-Buffet-Warmers-fig-6 Overhead Controls for GRBW-XX modelsHatco-GRBW-Series-GLO-RAY-Buffet-Warmers-fig-7 Base Controls for GRBW-XX models

Maximum Pan Capacities

  • GRBW-24 ………………………………………………..1 Full-Size Pan
  • GRBW-30 and -36 ……………………………………2 Full-Size Pans
  • GRBW-42 and -48 ……………………………………3 Full-Size Pans
  • GRBW-54 and -60 ……………………………………4 Full-Size Pans
  • GRBW-66 and -72 ……………………………………5 Full-Size Pans

TU

General
Hatco Glo-Ray Buffet Warmers are designed for maximum durability and performance, with minimum maintenance.

CEEB TOOM

ELECTRIC SHOCK HAzARD:

  • Turn OFF the power switch, unplug the power cord and allow the unit to cool before performing any maintenance or cleaning.
  • DO NOT submerge or saturate with water. unit is not waterproof. Do not operate if the unit has been submerged or saturated with water.
  • Tsis txhob ua kom huv si lossis siv dej ntau dhau ntawm chav tsev.
  • This unit is not “jet-proof” construction. Do not use a jet-clean spray to clean this unit.
  • Tsis txhob ntxuav lub tsev thaum nws muaj zog lossis kub.

This unit has no “user-serviceable” parts. If service is required on this unit, contact an Authorized Hatco Service Agent or contact the Hatco Service Department at 800-558-0607 or 414-671-6350; fax 800-690-2966; or International fax 414-671-3976.

Ntxuav
To preserve the finish of the unit as well as maintain performance, it is recommended that the unit be cleaned daily.

TSAB NTAWV CEEB TOOM

  • Submerging or saturating the unit with water will damage the unit and void the product warranty.
  • Do not drag or slide the unit when moving or installing. Carefully lift the unit to prevent the rubber feet from tearing off.
  • TSEEM CEEB—DO NOT use paper towels or glass cleaners to clean plastic surfaces such as sneeze guards and flip-up doors. Paper towels and glass cleaners may scratch the material. Wipe off plastic surfaces using a soft, clean, and damp daim ntaub.
  1. Tua lub tsev, tshem tawm cov hlua hluav taws xob, thiab cia lub tsev txias.
  2. Wipe down all exterior and interior surfaces using a damp cloth. a non-abrasive cleaner may be used for difficult stains. Hard-to-reach areas should be cleaned using a small brush and mild soap.
  3. Clean the plastic sneeze guards, side panels, and front enclosure using a mild, soapy water solution and a damp, soft cloth. NOTICE: DO NOT use paper towels or glass cleaners.

Replacing Display Light Bulbs

CEEB TOOM
use only light bulbs that meet or exceed National Sanitation Foundation (NSF) standards and are specifically designed for food holding areas. Breakage of light bulbs not specially coated could result in personal injury and/or food contamination.

The display lights are incandescent light bulbs that illuminate the warming area. Each bulb has a special coating to guard against injury and food contamination in the event of breakage.

  1. Tua lub tsev, tshem tawm cov hlua hluav taws xob, thiab cia lub tsev txias.
  2. Unscrew the light bulb from the unit and replace it with a new, specially-coated incandescent light bulb.

CEEB TOOM:

  • Hatco shatter-resistant light bulbs meet NSF standards for food holding and display areas. For 120 V applications, use Hatco P/N 02.30.081.00. For 220, 240, 220–230, and 230–240 V, use Hatco P/N 02.30.082.00.
  • Shatter-resistant halogen bulbs are available in place of standard incandescent bulbs. Halogen bulbs have a special coating to guard against injury and food contamination in the event of breakage. For 120 V applications, use Hatco P/N 02.30.081.00. For 220, 240, 220–230, and 230–240 V applications use Hatco P/N 02.30.082.00.

CEEB TOOM

ELECTRIC SHOCK HAzARD:
use only Genuine Hatco Replacement Parts when service is required. Failure to use Genuine Hatco Replacement Parts will void all warranties and may subject operators of the equipment to hazardous electrical voltage, ua rau hluav taws xob poob lossis hlawv. Hatco Qhov Chaw Hloov Kho Qhov Tseeb tau teev tseg kom ua haujlwm nyab xeeb hauv ib puag ncig uas lawv tau siv. Qee qhov chaw tom qab lossis cov khoom hloov pauv tsis muaj cov yam ntxwv uas yuav ua rau lawv ua haujlwm zoo hauv Hatco cov cuab yeej.

CUA LWM YAM

CEEB TOOM

  • This unit must be serviced by trained and qualified personnel only. Service by unqualified personnel may lead to electric shock or burn.
  • ELECTRIC SHOCK HAzARD: Turn OFF the power switch, unplug the power cord, and allow the unit to cool before performing any maintenance or cleaning.

Hatco-GRBW-Series-GLO-RAY-Buffet-Warmers-fig-14

OPTIONS THIAB ACCESSORIES

Front Enclosure and Side Panels
One plastic front enclosure and two plastic side panels are available as an option for all GRBW models. Use the following procedure to install the front enclosure and side panels.

  1. attach the two enclosure brackets and the two-panel brackets to the bottom of the unit.
    • Unscrew the four feet or legs from each corner of the unit.
    • Screw the feet or legs through the appropriate brackets and into the base. The two enclosure brackets should be installed on the front of the unit. The two-panel brackets should be installed on the rear of the unit.Hatco-GRBW-Series-GLO-RAY-Buffet-Warmers-fig-8 CEEB TOOM: Enclosure brackets support the front enclosure and the side panels. Panel brackets only support the side panels.
  2. Install the front enclosure.
    • Slide weld screws into the T-slot. Place the weld screws into the approximate position to align with the holes in the front enclosure.Hatco-GRBW-Series-GLO-RAY-Buffet-Warmers-fig-9
    • Position the bottom of the front enclosure into the two enclosure brackets.
    • align the weld screws with the holes in the top of the front enclosure and support trim. Secure using the supplied cap nuts. Do not over-tighten the cap nuts.Hatco-GRBW-Series-GLO-RAY-Buffet-Warmers-fig-10
  3. Install the side panels. To install each side panel:
    • Remove the screw on the top of each support post.
    • Position the side panel in the panel bracket and the enclosure bracket. make sure the side panel sits under the front enclosure.
    • attach the upper bracket to the top of the support posts using the previously removed screws.Hatco-GRBW-Series-GLO-RAY-Buffet-Warmers-fig-11

Sab Panels
Two plastic side panels are available as an option for all GRBW models. Use the following procedure to install each side panel.

  1. attach the four-panel brackets to the bottom of the unit.
    • Unscrew the four feet or legs from each corner of the unit
    • Screw the feet or legs through the appropriate bracket and into the base.
      CEEB TOOM: The four-panel brackets must be installed in the proper location and orientation. Refer to the illustration for proper bracket installation information.
  2. Position the side panels in the panel brackets.
  3. attach the two upper brackets to the top of each side of the unit using supplied screws.Hatco-GRBW-Series-GLO-RAY-Buffet-Warmers-fig-12

Overhead Heat Control
Optional overhead heat control is available for models GRBW-24 through GRBW-60. This infinite control allows the operator to manually adjust the overhead heat output from full wattage down to any desired level.

4 "(102 hli) Adjustable Legs
4″ (102 mm) adjustable legs are available as an accessory. 4″ (102 mm) adjustable legs come standard on GRBW-42 or larger models. Install the legs by screwing into the bottom of the unit until hand tight. Do not over-tighten.

Pan Rails
Pan Rails are available accessories for all GRBW models and come in 2, 3, 4, or 5 pan sizes.

Hardcoated Surface
an optional hard coated base surface is available for all GRBW models in place of the standard stainless steel surface.

Sneeze Guards
additional sneeze guard sizes are available for all GRBW models. The two additional sizes are 9-3/8″ (238 mm) and 14″ (356 mm).

Sign Holder
Display sign holders are available as accessories for all GRBW models. Use the following procedure to install a sign holder.

  1. Remove the two screws from each side of the unit. The screws are located toward the front and on the side of the unit.
  2. align sign holder holes with the screw holes on the side of the unit.
  3. Install the sign holder to the unit using the original screws.Hatco-GRBW-Series-GLO-RAY-Buffet-Warmers-fig-13

Display Sign Holder assembly

TSIS TXAUS SIAB

KHOOM NTOO

Hatco lav cov khoom lag luam uas nws tsim khoom ("Cov Khoom") kom tsis txhob muaj qhov tsis zoo ntawm cov khoom siv thiab kev ua haujlwm, raws li kev siv thiab kev pabcuam, rau ib lub sijhawm ntawm ib (1) xyoo txij li hnub ntawm kev yuav khoom thaum nruab thiab tswj raws li Hatco cov lus qhia sau lossis 18 lub hlis txij li hnub xa khoom los ntawm Hatco. Tus neeg yuav khoom yuav tsum tsim cov khoom hnub yuav khoom los ntawm kev sau npe cov khoom nrog Hatco lossis los ntawm lwm txoj kev txaus siab rau Hatco hauv nws qhov kev txiav txim siab ib leeg.

Hatco lav cov khoom nram qab no kom tsis txhob muaj qhov tsis xws luag hauv cov ntaub ntawv thiab kev ua haujlwm txij li hnub ntawm kev yuav khoom (raws li cov xwm txheej hauv qab no) rau lub sijhawm (s) ntawm lub sijhawm thiab ntawm cov xwm txheej hauv qab no:

  • Ib (1) Xyoo Parts thiab Labor PLUS Ib (1) Xyoo Ntxiv Ntxiv-tsuas Warranty:
    • Conveyor Toaster Elements (hlau sheathed)
    • Drawer Warmer Elements (hlau sheathed)
    • Drawer Warmer Drawer Rollers thiab Slides
    • Strip Heater Elements (hlau sheathed)
    • Zaub Warmer Elements (hlau sheathed cua cua sov)
    • Tuav Txee Elements (hlau sheathed cua cua sov)
    • Heated Well Elements — HW and HWB Series (metal sheathed)
  • Ob (2) Xyoo Kev Ua Haujlwm thiab Kev Ua Haujlwm Warranty:
    • Induction Ranges
    • Induction cua sov
  • Ib (1) Xyoo Parts thiab Labor PLUS Plaub (4) Xyoo Parts-tsuas Warranty:
    3CS thiab FR Tank
    Ib (1) Xyoo Parts thiab Labor PLUS Cuaj (9) Xyoo Parts-Tsuas Warranty ntawm:
    • Electric Booster Heater Tanks
    • Gas Booster rhaub Tanks
  • Cuaj caum (90) Hnub Parts-Tsuas Warranty:
    Hloov Xaiv

COV NTAUB NTAWV KHWV NYIAJ HAIS TIAS UA NTEJ THIAB RAU LWM YAM LOS NTAWM LWM YAM LOS TXOG, LOSSIS UA NTEJ, TXWV TSIS PUB COJ MUS RAU LEEJ TWG UA NTEJ LOS NTAWM TXOJ CAI LOSSIS TXUJ CI RAU LUB HOM PHIAJ LOSSIS LUB CAIJ LOSSIS TXOJ CAI LOSSIS TXUJ CI.

Tsis muaj kev txwv qhov dav dav ntawm cov lus hais saum toj no, TSEEM CEEB TSIS TXAUS SIAB: Coated incandescent teeb qhov muag teev, fluorescent teeb, kub lamp qhov muag teev, coated halogen teeb qhov muag teev, halogen tshav kub lamp qhov muag teev, xenon teeb qhov muag teev, LED teeb lub raj, iav Cheebtsam, thiab fuses; Cov khoom lag luam tsis ua haujlwm hauv lub tank booster, fin tube heat exchanger, lossis lwm yam khoom siv cua sov los ntawm liming, sediment buildup, tshuaj tua kab mob, los yog khov; los yog khoom misuse, tamping los yog misapplication, tsis tsim nyog installation, los yog daim ntawv thov ntawm tsis tsim nyog voltage.

TXOJ CAI TXOJ CAI NTAWM LUB SIJ HAWM
Hatco’s liability and Buyer’s exclusive remedy hereunder will be limited solely, at Hatco’s option, to repair or replacement using new or refurbished parts or Products by Hatco or a Hatco-authorized service agency (other than where Buyer is located outside of the United States, Canada, United Kingdom, or Australia, in which case Hatco’s liability and Buyer’s exclusive remedy hereunder will be limited solely to replacement of a part under warranty) with respect to any claim made within the applicable warranty period referred to above. Hatco reserves the right to accept or reject any such claim in whole or in part. In the context of this Limited Warranty, “refurbished” means a part or Product that has been returned to its original specifications by Hatco or a Hatco-authorized service agency. Hatco will not accept the return of any Product without prior written approval from Hatco, and all such approved returns shall be made at Buyer’s sole expense.

HATCO yuav tsis raug lav, nyob rau hauv ib qho xwm txheej, rau qhov kev puas tsuaj los yog raug xwm txheej, suav nrog tab sis tsis txwv rau cov nqi zog lossis cov txiaj ntsig poob uas tshwm sim los ntawm kev siv lossis khoom siv tsis tau zoo Lwm yam khoom lossis khoom siv.

AUTHORIZED PARTS DISTRIBUTORS

CALIFORNIA

  • Industrial Electric Commercial Parts & Service, Inc. Huntington Beach 714-379-7100
  • Chapman Appl. Service San Diego 619-298-7106 P & D Appliance Commercial Parts & Service, Inc. S. San Francisco 650-635-1900

NEW YORK

  • Alpro Service Co.
  • Maspeth 718-386-2515
  • Duffy’s – AIS
  • Buffalo 716-884-7425 3Wire
  • Plattsburgh 800-634-5005
  • Duffy’s – AIS Sauquoit 800-836-1014
  • J.B. Brady, Inc. Syracuse 315-422-9271

Canada

ALBERTA

  • Cov Khoom Siv Khoom Noj Khoom Haus Tseem Ceeb
  • Edmonton 780-438-1690

COJ COLUMBIA

  • Cov Khoom Siv Khoom Noj Khoom Haus Tseem Ceeb
  • Vancouver 604-433-4484
  • Cov Khoom Siv Khoom Noj Khoom Haus Tseem Ceeb
  • Victoria 250-920-4888

Sau npe koj chav nyob online!
See the IMPORTANT OWNER INFORMATION section for details.

Enregistrez votre appareil en ligne!
Lisez la section INFORMATIONS TSEEM CEEB POUR LE PROPRIETAIRE pour plus d'informations.

HATCO CORPORATION
P.O. Box 340500 Milwaukee, WI 53234-0500 U.S.A. 800-558-0607 414-671-6350 support@hatcocorp.com. www.hatcocorp.com.

Cov ntaub ntawv / Cov ntaub ntawv

Hatco GRBW Series GLO-RAY Buffet Warmers [pdf] Owner's Manual
GRBW Series GLO-RAY Buffet Warmers, GRBW Series, GLO-RAY Buffet Warmers, Buffet Warmers, GLO-RAY, Warmers
Hatco GRBW Series GLO-RAY Buffet Warmers [pdf] Phau Ntawv Qhia
GRBW Series GLO-RAY Buffet Warmers, GRBW Series, GLO-RAY Buffet Warmers, Buffet Warmers, Warmers

References

Cia ib saib

Koj email chaw nyob yuav tsis tsum luam tawm. Yuav tsum tau teb cov cim *