FOS technologies Razor Laser Multibeam RGB Laser Moving Head
Kev ntim khoom
Thank you for choosing our products. For your own safety, please read this manual before installing the device. This manual covers important information on installation and applications. Please install and operate the fixture with the following instructions, make sure the power is off before opening the light or repairing it. Meanwhile, please keep this manual well for future needs.
It is made of a new type of high-temperature strength of engineering plastics and cast aluminum casing with nice outlook. The fixture is designed and manufactured strictly following CE standards, complying with international standard DMX512 protocol. It’s available independently controlled and linkable with each other for operation. And it is applicable for large-scale live performances, theaters, studios, nightclubs and discos. 6 modules RGB laser light which features high brightness and stability. Please carefully unpack it when you receive the fixture and check whether it is damaged during the transportation.
Cov Lus Qhia Kev Nyab Xeeb
CEEV FAJ!
Ceev faj nrog koj cov haujlwm. Nrog kev txaus ntshai voltage, you can suffer a dangerous electric shock when touching wires
This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this user manual.
Tseem ceeb:
Kev puas tsuaj tshwm sim los ntawm kev tsis saib xyuas ntawm tus neeg siv phau ntawv no yuav tsis raug lav. Tus neeg muag khoom yuav tsis lees txais kev lav phib xaub rau qhov tshwm sim los yog teeb meem.
If the device has been exposed to temperature changes due to environmental changes, do not switch it on immediately. The arising condensation could damage the device. Leave the device switched off until it has reached room temperature. This device falls under protection-class I. Therefore, it is essential that the device be earthed. The electric connection must carry out by a qualified person. The device shall only be used with rate voltage thiab zaus. Xyuas kom meej tias muaj voltage is not higher than stated at the end of this manual. Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case, replacement of the cable must be done by an authorized dealer.
Ib txwm txiav tawm ntawm lub mains, thaum lub cuab yeej tsis siv lossis ua ntej ntxuav nws. Tsuas yog tuav txoj hlua hluav taws xob los ntawm lub ntsaws. Tsis txhob rub tawm lub plug los ntawm rub lub hwj chim qaum.
During the initial start-up, some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective, it should decrease gradually. Please don’t project the beam onto combustible substances. Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for smooth air flow, so there should be no shelter for fans and ventilation for heat radiation. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
Ntsiab nta
- Voltage: AC100-240V,50/60HZ
- Laser color: RGB full color
- Laser hwj chim: 3W
- RGB 500mw*6PCS （R:100mw G:200mw B:200mw） Laser pattern: a variety of rough beam effect patterns.
- Y-Axis rotating: 240°
- Lub kaum sab xis: 270 °
- Control mode: Music / Automatic / DMX512 (11/26/38CH) Scanning system: stepping motor
- Scanning angle of motor: 25 degrees
- Rated power：<180W
- Working environment: indoor Lamp
- Khoom loj: 85 x 16 x 45 cm
- Size of carton case (1in1): 92 x 16 x 32 cm
- N.W: 11kgs / G.W：12.6kgs
- Size of carton case (2in1): 94.5 x 34 x 33.5 cm
- N.W: 23kgs / G.W：26.5kgs
Cov Lus Qhia Ua Haujlwm
- The moving head is for laser purposes.
- Don’t turn on the fixture if it’s been through severe temperature difference like after transportation because it might damage the light due to the environmental changes. So, make sure to operate the fixture until it is in normal temperature.
- Lub teeb no yuav tsum tau khaws cia kom deb ntawm qhov muaj zog tshee thaum lub sijhawm thauj lossis txav mus los.
- Tsis txhob rub lub teeb los ntawm lub taub hau xwb, lossis nws yuav ua rau muaj kev puas tsuaj rau cov khoom siv tshuab.
- Don’t expose the fixture in overheat, moisture or environment with too much dust when installing it. And don’t lay any power cables on the floor. Or it might cause electronic shock to the people.
- Xyuas kom tseeb tias qhov chaw installation yog nyob rau hauv kev nyab xeeb zoo ua ntej txhim kho lub fixture.
- Nco ntsoov muab cov saw hlau ruaj ntseg thiab xyuas seb cov ntsia hlau puas raug ntsia hlau zoo thaum txhim kho cov khoom siv.
- Make sure the lens is in good condition. It’s recommended to replace the units if there are any damages or severe scratches.
- Xyuas kom tseeb tias lub fixture yog ua los ntawm cov neeg ua haujlwm tsim nyog uas paub lub fixture ua ntej siv.
- Khaws cov pob khoom qub yog tias xav tau kev xa khoom thib ob.
- Tsis txhob sim hloov cov khoom siv yam tsis muaj kev qhia los ntawm cov chaw tsim khoom lossis cov chaw kho mob uas raug xaiv.
- Nws tsis yog nyob rau hauv warranty ntau yam yog hais tias muaj tej yam malfunctions los ntawm tsis ua raws li cov neeg siv phau ntawv ua hauj lwm los yog tej yam tsis raug cai ua hauj lwm, xws li shock short circuit, hluav taws xob shock, lamp tawg, etc.
Press MENU to choose Address / DMX/ Color/ Manual/ Demo /Auto/Sound/ Temp /Version /Hours, then press ENTER to confirm or to enter the next step.if there are more function for options, press UP/DOWN to choose, then press ENTER to confirm, then press MENU to exit, or wait for 10 and exit automatically.
Lus Cim:
If no operation on any button, the display will turn off automatically in 20 seconds; if no DMX signal, the first dot of the display will turn on statically, if with DMX signal, the dot will flash
- DMX Address A001
- A512 Address Code
- Channel Mode 11CH, 26CH, 38
- CH channel selection
- Show Mode SOUND AUTO, effect selection
- Slave Mode MASTER, SLAVE, main and auxiliary machine selection
- Black Out YES, NO Standby mode
- Sound State ON, OFF voice switch
- Sound Sense sound sensitivity (0 off, 100 most sensitive)
- Pan Inverse
- YES, NO level reverse
- Tilt1 Inverse YES, NO vertical reverse
- Tilt2 Inverse YES, NO vertical reverse
- Tilt3 Inverse YES, NO vertical reverse
- Tilt4 Inverse YES, NO vertical reverse
- Tilt5 Inverse YES, NO vertical reverse
- Tilt6 Inverse YES, NO vertical reverse
- Back Light ON, OFF backlight switch
- Auto Test Auto Test
- Firmware Version V104 software version number
- Defaults YES, NO Restore factory settings
- System Reset YES, NO Machine reset
DMX Channels 11Channel Mode
| CH | muaj nuj nqi | DMX Tus Nqi | Paub meej |
| 1 | Yias Tsav | 0-255 | 0-360°positioning |
| 2 | Yias Tsav
ceev |
0-255 | Los ntawm ceev mus qeeb |
| 3 | Tilt1—Tilt6
motor stroke |
0-255 | 0 no function 1-255
0°-360° positioning |
| 4 | Tilt lub cev muaj zog
ceev |
0-255 | Los ntawm ceev mus qeeb |
|
5 |
Yuav tus kheej |
0-55 | Tsis muaj nuj nqi |
| 56-80 | Self-propelled effect 1 (XY
uncontrollable) |
||
| 81-105
106-130 131-155 156-180 |
Self-propelled effect 2 (XY uncontrollable)…Self-propelled effect 5 (XY uncontrollable) | ||
| 181-205 | Sound control (XY
uncontrollable) |
||
| 206-230 | Self-propelled effect 6 (XY
uncontrollable) |
||
| 231-255 | Sound control (XY
uncontrollable) |
||
| 6 | Yuav tus kheej
ceev |
0-255 | self-propelled speed and
Sound-activated sensitivity |
| 7 | Dimmer | 0-255 | 0-100% total dimming |
|
8 |
Strobe |
0-9 | Tsis muaj strobe |
| 10-255 | Strobe ceev los ntawm qeeb mus ceev | ||
|
9 |
Laser nyhuv |
0-15 | Tsis muaj nuj nqi |
| 16-27 | Nyhuv 1 | ||
|
...... |
Every time the DMX value is increased by 12, there will be
an effect |
||
| 232-243 | Nyhuv 19 | ||
| 244-255 | Nyhuv 20 | ||
| 10 | Laser nyhuv | 0-255 | self-propelled speed from fast |
| ceev | kom qeeb | ||
|
11 |
Pib dua |
0-249 | Tsis muaj nuj nqi |
| 250-255 | machine reset (value stays for
5 vib nas this) |
26Channel Mode
| CH | muaj nuj nqi | DMX Tus Nqi | Paub meej |
| 1 | Yias Tsav | 0-255 | 0-360°positioning |
| 2 | Yias Tsav
ceev |
0-255 | Los ntawm ceev mus qeeb |
| 3 | Tilt1 motor | 0-255 | 0°-360° positioning |
| 4 | Tilt2 motor | 0-255 | 0°-360° positioning |
| 5 | Tilt3 motor | 0-255 | 0°-360° positioning |
| 6 | Tilt4 motor | 0-255 | 0°-360° positioning |
| 7 | Tilt5 motor | 0-255 | 0°-360° positioning |
| 8 | Tilt6 motor | 0-255 | 0°-360° positioning |
| 9 | Tilt1-Tilt6
lub cev muaj zog |
0-255 | 0 no function 1-255 0°-360°
teeb tsa |
| 10 | Tilt lub cev muaj zog
ceev |
0-255 | speed from fast to slow |
|
11 |
Yuav tus kheej |
0-55 | Tsis muaj nuj nqi |
| 56-80 | Self-propelled effect 1 (XY
uncontrollable) |
||
| 81-105
106-130 131-155 156-180 |
Self-propelled effect 2 (XY uncontrollable)…Self-propelled effect 5 (XY uncontrollable) | ||
| 181-205 | Sound control (XY
uncontrollable) |
||
| 206-230 | Self-propelled effect 6 (XY
uncontrollable) |
||
| 231-255 | Sound control (XY
uncontrollable) |
||
| 12 | Yuav tus kheej
ceev |
0-255 | self-propelled speed and
Sound-activated sensitivity |
| 13 | Dimmer | 0-255 | 0-100% total dimming |
| 14 | Strobe | 0-9 | Tsis muaj strobe |
| 10-255 | Strobe ceev los ntawm qeeb mus ceev | ||
| 15 | Red laser 1-6 tsuav |
0-255 | 0 tsis muaj haujlwm
1-255 1-100% dimming |
| 16 | Ntsuab laser
1-6 dimming |
0-255 | 0 tsis muaj haujlwm
1-255 1-100% dimming |
| 17 | Blue laser 1-6
tsuav |
0-255 | 0 no function 1-255 1-100%
tsuav |
|
18 |
The first group of RGB lasers |
0-31 | Off |
| 32-63 | Liab | ||
| 64-95 | Ntsuab | ||
| 96-127 | Blue | ||
| 128-159 | Daj | ||
| 160-191 | Ntshav | ||
| 192-223 | Cyan | ||
| 224-255 | Tas kaj | ||
|
19 |
The second group of RGB lasers |
0-31 | Off |
| 31-63 | Liab | ||
| 64-95 | Ntsuab | ||
| 96-127 | Blue | ||
| 128-159 | Daj | ||
| 160-191 | Ntshav | ||
| 192-223 | Cyan | ||
| 224-255 | Tas kaj | ||
|
20 |
The third group of RGB lasers |
0-31 | Off |
| 32-63 | Liab | ||
| 64-95 | Ntsuab | ||
| 96-127 | Blue | ||
| 128-159 | Daj | ||
| 160-191 | Ntshav | ||
| 192-223 | Cyan | ||
| 224-255 | Tas kaj | ||
|
21 |
The fourth group of RGB lasers |
0-31 | Off |
| 32-63 | Liab | ||
| 64-95 | Ntsuab | ||
| 96-127 | Blue | ||
| 128-159 | Daj | ||
| 160-191 | Ntshav | ||
| 192-223 | Cyan | ||
| 224-255 | Tas kaj | ||
|
22 |
The fifth group of RGB lasers |
0-31 | Off |
| 32-63 | Liab | ||
| 64-95 | Ntsuab | ||
| 96-127 | Blue | ||
| 128-159 | Daj | ||
| 160-191 | Ntshav | ||
| 192-223 | Cyan | ||
| 224-255 | Tas kaj | ||
| 23 | Qhov thib rau | 0-31 | Off |
| group of RGB lasers | 32-63 | Liab | |
| 64-95 | Ntsuab | ||
| 96-127 | Blue | ||
| 128-159 | Daj | ||
| 160-191 | Ntshav | ||
| 192-223 | Cyan | ||
| 224-255 | Tas kaj | ||
|
24 |
Laser nyhuv |
0-15 | Tsis muaj nuj nqi |
| 16-27 | Nyhuv 1 | ||
|
...... |
Every time the DMX value is
increased by 12, there will be an effect |
||
| 232-243 | Nyhuv 19 | ||
| 244-255 | Nyhuv 20 | ||
| 25 | Laser nyhuv
ceev |
0-255 | self-propelled speed from fast to
qeeb |
|
26 |
Pib dua |
0-249 | Tsis muaj nuj nqi |
| 250-255 | machine reset (value stays for 5 seconds) |
38Channel Mode
| CH | muaj nuj nqi | DMX Tus Nqi | Paub meej |
| 1 | Yias Tsav | 0-255 | 0-360°positioning |
| 2 | Yias Tsav
ceev |
0-255 | Los ntawm ceev mus qeeb |
| 3 | Tilt1 motor | 0-255 | 0-360°positioning |
| 4 | Tilt2 motor | 0-255 | 0-360°positioning |
| 5 | Tilt3 motor | 0-255 | 0-360°positioning |
| 6 | Tilt4 motor | 0-255 | 0-360°positioning |
| 7 | Tilt5 motor | 0-255 | 0-360°positioning |
| 8 | Tilt6 motor | 0-255 | 0-360°positioning |
| 9 | Tilt1—Tilt6
motor stroke |
0-255 | 0 tsis muaj haujlwm
1-255 0°-360° positioning |
| 10 | Tilt motor speed | 0-255 | speed from fast to slow |
|
11 |
Yuav tus kheej |
0-55 | Tsis muaj nuj nqi |
| 56-80 | Self-propelled effect 1 (XY
uncontrollable) |
||
| 81-105
106-130 131-155 156-180 |
Self-propelled effect 2 (XY uncontrollable)…Self-propelled effect 5 (XY uncontrollable) | ||
| 181-205 | Sound control (XY uncontrollable) | ||
| 206-230 | Self-propelled effect 6 (XY |
| uncontrollable) | |||
| 231-255 | Sound control (XY uncontrollable) | ||
| 12 | Yuav tus kheej
ceev |
0-255 | self-propelled speed and
Sound-activated sensitivity |
| 13 | Dimmer | 0-255 | 0-100% total dimming |
| 14 | Strobe | 0-9 | Tsis muaj strobe |
| 10-255 | Strobe ceev los ntawm qeeb mus ceev | ||
| 15 | Red laser 1-6
tsuav |
0-255 | 0 tsis muaj haujlwm
1-255 1-100% dimming |
| 16 | Green laser 1-6
tsuav |
0-255 | 0 tsis muaj haujlwm
1-255 1-100% dimming |
| 17 | Blue laser 1-6
tsuav |
0-255 | 0 tsis muaj haujlwm
1-255 1-100% dimming |
| 18 | The first group
of red lasers |
0-255 | 0-100% dimming |
| 19 | The first group
of green lasers |
0-255 | 0-100% dimming |
| 20 | The first group
of blue lasers |
0-255 | 0-100% dimming |
|
21 |
Qhov thib ob
group of red lasers |
0-255 |
0-100% dimming |
| ...... | ...... | ...... | ...... |
| 33 | The sixth group
of red lasers |
0-255 | 0-100% dimming |
| 34 | The sixth group
of green lasers |
0-255 | 0-100% dimming |
| 35 | The sixth group
of blue lasers |
0-255 | 0-100% dimming |
|
36 |
Laser nyhuv |
0-15 | Tsis muaj nuj nqi |
| 16-27 | Nyhuv 1 | ||
| ...... | Every time the DMX value is increased
by 12, there will be an effect |
||
| 232-243 | Nyhuv 19 | ||
| 244-255 | Nyhuv 20 | ||
| 37 | Laser nyhuv
ceev |
0-255 | self-propelled speed from fast to slow |
|
38 |
Pib dua |
0-249 | Tsis muaj nuj nqi |
| 250-255 | machine reset (value stays for 5 seconds) |
Kev tu thiab tu
The following points must be considered during the inspection:
- All screws for installing the devices or parts of the device must be tightly connected and must not be corroded.
- There must not be any deformations on the housing, color lenses, fixations and installation spots (ceiling, suspension, trussing).
- Mechanically txav qhov chaw yuav tsum tsis txhob pom ib qho kev hnav thiab yuav tsum tsis txhob tig nrog qhov tsis sib xws.
- Cov khoom siv hluav taws xob hluav taws xob yuav tsum tsis txhob pom muaj kev puas tsuaj, cov khoom siv qaug zog lossis sediments.
Further instructions depending on the installation spot and usage must be adhered by a skilled installer and any safety problems have to be removed.
CEEV FAJ!
Disconnect los ntawm mains ua ntej pib txij nkawm.
In order to make the lights in good condition and extend the lifetime, we suggest a regular cleaning to the lights.
- Clean the inside and outside lens each week to avoid the weakness of the lights due to the accumulation of dust.
- Ntxuav lub kiv cua txhua lub lim tiam.
- A detailed electric check by an approved electrical engineer every three months makes sure that the circuit contacts are in good condition, and prevents the poor contact of the circuit from overheating.
We recommend frequent cleaning of the device. Please use a moist, lint-free cloth. Never use alcohol or solvents. There are no serviceable parts inside the device. Please refer to the instructions under “Installation instructions”.
Cov ntaub ntawv / Cov ntaub ntawv
 |
FOS technologies Razor Laser Multibeam RGB Laser Moving Head [pdf] Tus neeg siv phau ntawv Razor Laser, Multibeam RGB Laser Moving Head, RGB Laser Moving Head, Moving Head, Razor Laser |
