ATEN Command Line Interface Control System Tus Neeg Siv Qhia
Hais Txog Cov Lus Qhia no
ATEN Control System txais Telnet raws tu qauv siv CLI rau cov neeg siv xa cov lus txib. Phau ntawv qhia no siv rau ATEN controllers thiab extension boxes. Cov lus txib no tso cai rau koj los teeb tsa Telnet chaw, I / O chaw, xa cov lus txib mus rau cov tswj / txuas ntxiv lub thawv tswj hwm, thiab tau txais cov lus teb.
Nco tseg: I/O nqis los ntawm CLI yuav ploj yog tias a viewer yog uploaded los ntawm ATEN Configurator (GUI) tom qab ntawd.
Txhawm rau saib cov kev tswj hwm tam sim no ntawm tus tswj hwm, mus saib hauv web lub console.
Rov pib dua
Kev siv:
Reboot tus maub los.
Syntax:
reboot thiab rov pib dua
lees paub:
Hais kom OK↙ : Hais kom raug thiab muaj nuj nqi raug tua.
Command incorrect↙ : Hais kom ua thiab/los yog tsis raug thiab tsis raug.
Example:
reboot↙: reboot ntaus ntawv
Pab
Kev siv:
Tso cov lus qhia rau kev ua kom CLI hom ntawm tus maub los.
Syntax:
pab ↙
lees paub:
Hais kom OK↙ : Hais kom raug thiab muaj nuj nqi raug tua.
Command incorrect↙ : Hais kom ua thiab/los yog tsis raug thiab tsis raug.
Example:
pab ↙ : tso saib kev qhia ntawm CLI hom
Echo
Kev siv:
Pab kom lossis lov tes taw tus maub los kom tau txais cov lus teb rau cov lus tau txais.
Syntax:
ncha [tswj] ↙
Parameter:
tswj : on – pab kom no function off – disable no function (default is off)
lees paub:
Hais kom OK↙ : Hais kom raug thiab muaj nuj nqi raug tua.
Command incorrect↙ : Hais kom ua thiab/los yog tsis raug thiab tsis raug.
Example:
eho on↙ : teeb tsa tus maub los kom teb tau cov lus tau txais.
Telnet
Kev siv:
Configure Telnet CLI hom teeb tsa.
Syntax:
telnet[timeout interval][login control]↙
Lo lus tseem ceeb:
timeout : Telnet session timeout interval setting login : Telnet login function setting
Parameter:
ncua sij hawm: kev sib tham timeout hauv feeb. (0 txhais tau tias yeej tsis timeout) (default is 5)
tswj : on – enable login function (default is on) off – disable login function
lees paub:
Hais kom OK↙ : Hais kom raug thiab muaj nuj nqi raug tua.
Command incorrect↙ : Hais kom ua thiab/los yog tsis raug thiab tsis raug.
Example:
telnet timeout 0↙ : configure timeout interval to never timeout telnet timeout 5↙ : configure timeout interval to 5 feeb telnet login off↙ : disable the login function
Serial
Kev siv:
Tswj thiab configure serial chaw nres nkoj chaw.
Syntax:
serial [p sequence] [type stype] [baud baudrate] [dbit databit] [parity sparity] [sbit stopbit] [fctrl flowctrl] [dtype datatype] [endchar chars] [checksumtype checksumtype] [acktimeout duration] [tswj "cov ntaub ntawv" ] [pab] ↙
Lo lus tseem ceeb:
p :pob
hom: serial hom
baud: baud nqi
dbit: cov ntaub ntawv
parity: serial parity
sbit: nres bit
fctrl: khiav tswj
dtype: cov ntaub ntawv hom
acktimeout : timeout duration (ms) yog siv rau tos cov lus teb los ntawm sendack tswj.
endchar : tus cim kawg yog siv los txheeb xyuas cov lus tiav.
checksumtype : yog xav tau fw rau nws pib-calculate command checksum, muab hom checksum
pab: qhia cov lus qhia
Parameter:
sequence : chaw nres nkoj, sib cais los ntawm comma rau ntau qhov chaw nres nkoj
* (tag nrho cov chaw nres nkoj)
Hom: 232, 422, 485 (default 232)
baudrate: 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 (default 9600)
databit: 7, 8 (default 8)
sparity: tsis muaj, txawm, khib (default tsis muaj)
stopbit: 1, 2 (default 1)
flowctrl: tsis muaj, hw (default tsis muaj)
datatype: ascii, hex (default ascii)
checksumtype: tsis muaj, modbus (default tsis muaj)
Lub sijhawm: lub sijhawm tshwj xeeb (ms) (default 300)
chars: kawg cov cim tom qab cov lus tiav.
tswj : nyeem - tso saib tau txais cov lus ntawm qhov chaw nres nkoj tshwj xeeb
sau - xa cov ntaub ntawv los ntawm qhov chaw nres nkoj serial. Siv "cim npog cov ntaub ntawv. Siv \x cim xa
Hex code
sendack – xa cov ntaub ntawv los ntawm qhov chaw nres nkoj serial thiab tso saib tau txais cov lus
lees paub:
Hais kom OK↙ : Hais kom raug thiab muaj nuj nqi raug tua.
Command incorrect↙ : Hais kom ua thiab/los yog tsis raug thiab tsis raug.
Example:
Serial pab ↙: qhia cov lus qhia
serial p01 ↙ : tso saib cov ntaub ntawv teeb tsa ntawm serial port1.
serial p * ↙ : tso saib cov ntaub ntawv teeb tsa ntawm txhua qhov chaw nres nkoj serial.
serial p01 hom 232 baud 115200 dbit 8 parity none sbit 1 fctrl tsis muaj ↙ : configure port1.
serial p01,04,07 baud 19200 ↙ : configure port1, 4, 7 to baud rate 19200.
serial p02 baud 19200 ↙ : configure port2 to baud 19200 and use default settings for other parameters.
serial p02 dtype hex nyeem ↙ : tso saib cov lus tau txais ntawm port2 hauv HEX hom.
serial p03 sau “sw i01 o02\r\n” ↙ : xa cov ntawv ASCII 'sw i01 o02' los ntawm port3.
serial p03 sendack “sw i01 o02\x0D\x0A” ↙ : xa cov ntawv ASCII 'sw i01 o02' los ntawm port3 thiab tso saib cov lus tawm tswv yim.
Relay
Kev siv:
Tswj thiab configure relay ports.
Syntax:
relay [p sequence] [tpulse duration] [tswj] [pab] ↙
Lo lus tseem ceeb:
p :pob
tpulse: kaw lub sij hawm rau mem tes
pab: qhia cov lus qhia
Parameter:
sequence : chaw nres nkoj, sib cais los ntawm comma rau ntau qhov chaw nres nkoj
* (tag nrho cov chaw nres nkoj)
Duration: lub sij hawm lub sij hawm nyob rau hauv millisecond.
tswj: qhib-tawm
kaw - tig rau
mem tes - kaw lub relay channel ces qhib
toggle - relay toggle
nyeem – tso saib xwm txheej
lees paub:
Hais kom OK↙ : Hais kom raug thiab muaj nuj nqi raug tua.
Command incorrect↙ : Hais kom ua thiab/los yog tsis raug thiab tsis raug.
Example:
Relay pab ↙ : qhia cov lus qhia
relay p01 kaw ↙ : kaw port1 channel.
relay p01 qhib ↙ : qhib port1 channel.
relay p01,04,07 kaw ↙ : kaw chaw nres nkoj 1, 4, 7 relay channels.
relay p02 tpulse 500 pulse ↙ : kaw port2 500ms ces qhib.
relay p02 nyeem ↙ : tso saib port2 xwm txheej.
I/O
Kev siv:
Tswj thiab teeb tsa I / O ports.
Syntax:
io [p sequence] [type iotype] [lthresh threshold] [hthresh threshold] [tpulse duration] [tswj] [pab] ↙
Lo lus tseem ceeb:
p :pob
lthresh : low-bound threshold
hthresh : high-bound threshold
tpulse : lub sijhawm uas I / O tseem nyob rau theem siab hauv hom mem tes
pab: qhia cov lus qhia
CEEB TOOM: Yog hais tias tus parameter tsis tau teev tseg, tus nqi yav dhau los yuav raug siv.
Parameter:
sequence : chaw nres nkoj, sib cais los ntawm comma rau ntau qhov chaw nres nkoj
* (tag nrho cov chaw nres nkoj)
iotype: qhuav, vdc, dout
threshold : trigger threshold in voltage
Duration: lub sij hawm lub sij hawm nyob rau hauv millisecond.
tswj: qhib
kaw
mem tes
toggle
nyeem
lees paub:
Hais kom OK↙ : Hais kom raug thiab muaj nuj nqi raug tua.
Command incorrect↙ : Hais kom ua thiab/los yog tsis raug thiab tsis raug.
Example:
io pab ↙ : qhia cov lus qhia
io p01↙ : tso saib cov ntaub ntawv teeb tsa ntawm I/O port1.
io p*↙ : tso saib cov ntaub ntawv teeb tsa ntawm txhua qhov chaw nres nkoj I/O.
io p01 hom qhuav ↙ : configure port 1 to dry contact mode.
io p01 hom dout ↙ : configure port 1 to digital output mode.
io p01 hom vdc lthresh 1 hthresh 3 ↙ : configure port 1 to vdc mode with threshold settings.
io p01 qhib ↙ : qhib port1 channel.
io p01 kaw ↙ : kaw port1 channel.
io p01,04,07 kaw ↙ : kaw port1,4,7 channels.
io p02 tpulse 500 pulse ↙ : kaw port2 channel 500ms ces qhib.
io p02 nyeem ↙ : tso saib port2 xwm txheej.
IR
Kev siv:
Tswj thiab teeb tsa IR chaw nres nkoj.
Syntax:
ir [p sequence] [hom irtype] | [baud baudrate] [dbit databit] [parity sparity] [sbit stopbit] [dtype datatype] [checksumtype checksumtype] [tswj "cov ntaub ntawv"] [pab] ↙
Lo lus tseem ceeb:
p :pob
hom: hom tso zis rau qhov chaw tso zis tshwj xeeb
baud** : baud rate
dbit ** : cov ntaub ntawv me ntsis
parity ** : serial parity
sbit ** : nres bit
dtype** : data type
checksumtype** : Controller/extension box cia li xam cov checksum hom
pab: qhia cov lus qhia
CEEB TOOM:
* : Lo lus tseem ceeb no yog rau hom IR
** : Cov ntsiab lus no yog rau 232 hom
Yog hais tias tus parameter tsis tau teev tseg, tus nqi yav dhau los yuav raug siv.
Parameter:
sequence : chaw nres nkoj, sib cais los ntawm comma rau ntau qhov chaw nres nkoj
* (tag nrho cov chaw nres nkoj)
irtype: ir, 232 (default ir)
baudrate: 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 (default 9600)
databit: 7, 8 (default 8)
sparity: tsis muaj, txawm, khib (default tsis muaj)
stopbit: 1, 2 (default 1)
datatype: ascii, hex (default ascii)
checksumtype: tsis muaj, modbus (default tsis muaj)
tswj: sau - xa IR code lossis RS232 cov ntaub ntawv
lees paub:
Hais kom OK↙ : Hais kom raug thiab muaj nuj nqi raug tua. Command incorrect↙ : Hais kom ua thiab/los yog tsis raug thiab tsis raug.
Example:
ir pab ↙ : qhia cov lus qhia
ir p01 ↙ : tso saib cov ntaub ntawv teeb tsa ntawm IR port1.
ir p* ↙ : tso saib cov ntaub ntawv teeb tsa ntawm txhua qhov chaw IR.
ir p01,04,07 hom 232 ↙ : configure port1,4,7 to RS232 type
ir p01 type 232 baud 115200 dbit 8 parity none sbit 1 checksum type modbus ↙ :
configure port1 to RS232 type and the settings ir p02 sau dtype hex “0a0b0c” ↙ : xa hex format data 0a0b0c from port2
ir p02 baud 19200 ↙ : configure port2 to baud 19200 and use the default settings for other parameters.
ir p02 sau “sw i01 o02\r\n” ↙ : xa cov ntawv ASCII 'sw i01 o02' los ntawm port2.
ir p02 sau “sw i01 o02\x0D\x0A”↙ : xa cov ntawv ASCII 'sw i01 o02' los ntawm port2.
Cov ntaub ntawv / Cov ntaub ntawv
 |
ATEN Command Line Interface Control System [ua pdf] Cov neeg siv phau ntawv qhia Hais kom Line Interface, Tswj System, Command Line Interface Control System |
