Cov ntsiab lus zais
1 ARGOX I4 / iX4 Series GPIO Interface Control
2 Cov ntaub ntawv khoom
3 Cov lus qhia siv khoom
4 Specifications
5 Connector pin specification
6 Input/Output Signal Description
7 Cov ntaub ntawv / Cov ntaub ntawv
7.1 Cov ntaub ntawv

ARGOX-Logo

ARGOX I4 / iX4 Series GPIO Interface Control

ARGOX-I4-iX4-Series-GPIO-Interface-Control-PRO

Cov ntaub ntawv khoom

Specifications
GPIO interface yog tsim los rau Argox cov tshuab luam ntawv thiab cov khoom siv sab nraud.

  • Connector: D-Sub 15-pin poj niam connector
  • Input Pins: Txheem TTL qib
  • Output Pins: Txheem TTL theem, rub tawm 1K ohm sab hauv los ntawm 5V, siab tshaj plaws dab dej tam sim no 30mA
  • Cov khoom siv fais fab: 5V (max mov tam sim no 500mA), 24V (max mov tam sim no 1A)

Connector Pin Specification

  • Tag nrho cov input pins yog txhais raws li tus qauv TTL qib.
  • Tag nrho cov zis pins tau txhais raws li tus qauv TTL qib thiab sab hauv rub los ntawm 5V nrog lub dab dej siab tshaj plaws ntawm 30mA.
  • Hauv av (pin1 thiab pin8) ntawm GPIO board thiab lub teeb liab hauv av ntawm cov khoom siv sab nraud yuav tsum tau txuas ncaj qha.
  • Qhov txuas cable ntev ntawm GPIO interface thiab cov khoom siv sab nraud yuav tsum tsawg dua 15 feet.

Input/Output Signal Description
Muaj plaub tus pins input rau daim ntawv thov:

  1. Pib Sau (Pin 3):
    • Qhov teeb liab no pib ua haujlwm luam tawm (qhib qis).
    • Thaum lub tshuab luam ntawv tiav lawm, qhov kawg Print pin xa cov mem tes qis (20ms).
    • Cov ntaub ntawv npaj tus pin mus qis qis thaum cov ntaub ntawv npaj rau luam ntawv.

Cov lus qhia siv khoom

  • Kev teeb tsa:
    Ua raws li phau ntawv qhia kev teeb tsa kom txuas GPIO daim npav rau lub tshuab luam ntawv muaj.
  • Kev ua haujlwm:
    Program lossis kho qhov GPIO interface los tswj lub tshuab luam ntawv ua haujlwm.
  • Connector Pin Connections:
    Xyuas kom muaj kev sib txuas ntawm tus pins raws li cov ntsiab lus ntawm tus pin muab.
  • Cable Length:
    Khaws lub cable ntev ntawm GPIO interface thiab cov cuab yeej sab nraud hauv qab 15 ko taw kom tsis txhob muaj suab nrov thiab tsis raug.

FAQ

  • Q: Dab tsi yog qhov siab tshaj plaws dab dej tam sim no rau cov zis pins?
    A: Qhov siab tshaj plaws dab dej tam sim no rau cov zis pins yog 30mA.
  • Q: Kuv yuav ua li cas thiaj li tau txais lub teeb liab Start Print?
    A: Pib Print teeb liab pib lub tshuab luam ntawv thiab ua haujlwm qis. Xyuas kom ua raws li daim ntawv teev sijhawm rau kev ua haujlwm kom raug.

ARGOX-I4iX4-Series-GPIO-Interface-Control-Fig- (1)

https://www.argox.com

Specifications

  1. GPIO interface yog tsim los rau Argox cov tshuab luam ntawv thiab cov khoom siv sab nraud.ARGOX-I4iX4-Series-GPIO-Interface-Control-Fig- (2)
  2. GPIO interface ua haujlwm hauv kev tswj hwm tshwj xeeb los ntawm kev hloov cov teeb liab tawm tswv yim; nws yog programmable lossis customized, thiab cov teeb liab tso tawm qhia lub tshuab luam ntawv raws li txoj cai lossis qhov taw qhia ua haujlwm.ARGOX-I4iX4-Series-GPIO-Interface-Control-Fig- (3)
  3. GPIO interface yog raws li qhia hauv daim duab 2 thiab daim duab 3; nws siv D-Sub 15-pin poj niam connector.ARGOX-I4iX4-Series-GPIO-Interface-Control-Fig- (4)
  4. Connector pin txhais yog raws li nram no:
Tus Pin No. Hom Default Function

Kev piav qhia
1 P GND Lub zog xa rov qab ntawm +5V
2 P + 5 V Lub hwj chim ntxiv ntawm +5V
3 I Pib Sau Pib luam ntawv. Ua rau lub teeb liab no (siab mus rau qis) kom lub tshuab luam ntawv luam tawm ib daim ntawv tau txais hom ntawv.
4 I Pub Pub. Tig lub teeb liab no (los ntawm siab mus rau qis) los pub ib daim ntawv lo. Nws zoo ib yam li tus yuam sij "FEED" ntawm lub vaj huam sib luag.
5 I Ncua tseg Ncua tseg. Thaum lub teeb liab no tshwm sim (siab mus rau qis), lub tshuab luam ntawv nres lossis nres lub tshuab luam ntawv kom txog thaum lub teeb liab nres tom ntej no tshwm sim.
6 I Luam dua Luam dua. Lub tshuab luam ntawv rov luam daim ntawv lo kawg thaum lub teeb liab no tshwm sim (siab mus rau qis).
7 P 24v XNUMX Lub hwj chim ntxiv ntawm +24V
8 P GND Lub zog xa rov qab ntawm +24V
9 NC Tsis Txuas
10 O Kev_Req Kev pabcuam yuav tsum tau ua. Thaum lub tshuab luam ntawv yuam kev tshwm sim, cov teeb liab tso tawm no yuav hloov ntawm siab mus rau qis (qhib qis).
11 O Xaus Sau Xaus ntawm luam tawm. Tso tawm cov teeb liab mem tes qis hauv 20ms thaum kawg ntawm kev luam ntawv.
12 O Media tawm Media tawm. Thaum lub tshuab luam ntawv khiav tawm ntawm daim ntawv lossis muaj cov ntawv tsis zoo, cov teeb liab tso tawm no yuav hloov ntawm qhov siab mus rau qis (kwv yees qis).
13 O Ribbon Tawm Ribbon tawm. Thaum lub ribbon khiav tawm, qhov tso zis teeb liab no yuav hloov ntawm siab mus rau qis (qhib qis).
14 O Cov ntaub ntawv npaj Cov ntaub ntawv yog npaj txhij. Cov teeb liab tso zis no yuav hloov ntawm qhov siab mus rau qis (qis qis) thaum cov ntaub ntawv luam tawm tau txais thiab tos kom ua rau kev luam ntawv.
15 O OPT Fault Output txhaum. Thaum lub tshuab luam ntawv yuam kev tshwm sim, cov teeb liab tso tawm no yuav hloov ntawm siab mus rau qis (qhib qis).

Hom: P rau lub zog; Kuv rau Input; O rau Cov Lus Qhia 1

Connector pin specification

  1. Tag nrho cov pins input nyob rau hauv lub rooj yog txhais raws li tus qauv TTL theem.
  2. Tag nrho cov zis pins nyob rau hauv lub rooj yog txhais raws li tus qauv TTL theem; lawv tau rub 1K ohm sab hauv los ntawm 5V, thiab qhov siab tshaj plaws dab dej tam sim no yog 30mA.
  3. Muaj ob lub zog siv rau cov khoom siv sab nraud; Qhov siab tshaj plaws tam sim no ntawm 5V yog 500mA, thiab 24V yog 1A.
  4. Vim tias tag nrho cov teeb liab tsis raug cais tawm, hauv av (pin1 thiab pin8) ntawm GPIO board thiab cov teeb liab hauv av ntawm cov cuab yeej sab nraud yuav tsum tau txuas ncaj qha; nws yuav tsum tsis txhob sib txawv GND pins txuas rau GPIO pawg thawj coj saib thiab ua rau lub rooj tsavxwm no ua tsis tiav.
  5. Qhia tias qhov ntev ntawm kev sib txuas ntawm cable ntawm GPIO interface thiab cov khoom siv sab nraud yuav tsum tsawg dua 15 feet kom tsis txhob muaj suab nrov thiab yuam kev.

Input/Output Signal Description

Muaj plaub tus pins input rau daim ntawv thov.

  1. Tus Pin 3
    Pib Sau:
    • Cov teeb liab no ua rau lub tshuab luam ntawv pib ua haujlwm luam ntawv; nws yog active qis.
    • Thaum lub tshuab luam ntawv tiav lawm, tus pin tso zis ntawm End Print yuav xa cov mem tes qis (20ms), thiab cov khoom siv sab nraud yuav tsum tua lub teeb liab pib.
    • Thaum cov ntaub ntawv luam tawm tau txais, cov zis tus pin ntawm Cov Ntaub Ntawv Npaj yuav ua haujlwm qis.
    • Daim ntawv qhia sij hawm muaj nyob hauv daim duab 4.ARGOX-I4iX4-Series-GPIO-Interface-Control-Fig- (5)
  2. Tus Pin 4
    Pub:
    • Lub teeb liab yog cia lub tshuab luam ntawv pub cov xov xwm; lub sab hauv daim ntawv lo ntev teev qhov kev ncua deb.
    • Thaum lub sij hawm pub noj, tus pin tso zis ntawm Cov Ntaub Ntawv Npaj yuav ua haujlwm thiab ua tsis taus mus txog thaum kawg ntawm qhov pub.
    • Daim ntawv qhia sij hawm muaj nyob hauv daim duab 5.ARGOX-I4iX4-Series-GPIO-Interface-Control-Fig- (6)
  3. Tus Pin 5
    Ncua tseg:
    • Lub teeb liab ua rau lub tshuab luam ntawv nres nres; nws yog ib qho toggle (on/off) hom thaum lub tshuab luam ntawv yuav tsum tau nres ib ntus.
    • Thaum lub sijhawm ua haujlwm nres, cov zis tus pin ntawm OPT Fault yuav ua haujlwm qis thiab ua haujlwm tsis zoo kom txog thaum lub teeb liab nres rov ua haujlwm dua.
    • Daim ntawv qhia sij hawm muaj nyob hauv daim duab 6.ARGOX-I4iX4-Series-GPIO-Interface-Control-Fig- (7)
  4. Tus Pin 6
    Rov luam dua:
    • Qhov teeb liab no ua rau lub tshuab luam ntawv luam tawm daim ntawv lo kawg dua; nws yog active qis.
    • Thaum lub tshuab luam ntawv tiav lawm, tus pin tso zis ntawm End Print yuav xa cov mem tes (20ms), thiab cov cuab yeej sab nraud yuav tsum tua lub teeb liab rov qab.
    • Cov zis tus pin ntawm Cov Ntaub Ntawv Npaj yuav ua haujlwm thiab ua tsis taus mus txog thaum kawg ntawm kev luam ntawv.
    • Daim ntawv qhia sij hawm muaj nyob hauv daim duab 7.ARGOX-I4iX4-Series-GPIO-Interface-Control-Fig- (8)

Muaj rau qhov tso zis pins rau lub tshuab luam ntawv daim ntawv thov; daim ntawv teev sij hawm muaj nyob hauv daim duab 8.

  1. Tus Pin 10
    Serv_Req:
    • Lub teeb liab yuav ua haujlwm thaum lub tshuab luam ntawv yuam kev tshwm sim.
  2. Tus Pin 11
    Xaus Sau:
    • Nws qhia txog lub tshuab luam ntawv cov xwm txheej thiab ua haujlwm thaum nplooj ntawv luam ntawv tiav.
    • Lub sijhawm ua haujlwm yog li 20ms.
  3. Tus Pin 12
    Media tawm:
    • Nws qhia cov xwm txheej xov xwm thiab ua haujlwm thaum tawm xov xwm (daim ntawv) tawm tshwm sim.
    • Qhov teeb liab no txuas ntxiv mus txog thaum qhov kev ua yuam kev raug tshem tawm.
  4. Tus Pin 13
    Ribbon tawm:
    • Nws qhia txog cov xwm txheej ribbon thiab ua haujlwm thaum ribbon tawm tshwm sim.
    • Qhov teeb liab no txuas ntxiv mus txog thaum qhov kev ua yuam kev raug tshem tawm.
  5. Tus Pin 14
    Npaj cov ntaub ntawv:
    • Nws qhia tias lub tshuab luam ntawv tau txais cov ntaub ntawv luam tawm.
    • Hauv lub xeev no, lub tshuab luam ntawv tuaj yeem lees txais lub tswv yim Start Print signal los pib lub tshuab luam ntawv.
  6. Tus Pin 15
    OPT Fault:
    • Nws qhia tag nrho cov tshuab luam ntawv yuam kev. Yog tias nws ua haujlwm, thov ua tus txheej txheem daws teeb meem.
    • Qhov teeb liab no txuas ntxiv mus txog thaum qhov kev ua yuam kev raug tshem tawm.ARGOX-I4iX4-Series-GPIO-Interface-Control-Fig- (9)

https://www.argox.com.

Cov ntaub ntawv / Cov ntaub ntawv

ARGOX I4 / iX4 Series GPIO Interface Control [ua pdf] Phau ntawv qhia
I4, iX4 Series, I4 iX4 Series GPIO Interface Control, I4 iX4 Series, GPIO Interface Control, Interface Control, Tswj

Cov ntaub ntawv

Cia ib saib

Koj email chaw nyob yuav tsis raug luam tawm. Cov teb uas yuav tsum tau muaj yog cim *