Categories: HiB

HiB TRIM Curve, Round Installation Guide

TRIM Curve, Round

Trim Curve 40 Black: Art No 62010000
Trim Curve 40 Brushed Brass: Art No 62020000
Trim Curve 50 Black: Art No 62030000
Trim Curve 50 Brushed Brass: Art No 62040000
Trim Round 60 Black: Art No 62050000
Trim Round 60 Brushed Brass: Art No 62060000
Trim Round 80 Black: Art No 62060000
Trim Round 80 Brushed Brass: Art No 62070000

Fitting Instructions

Thank you for purchasing this HiB product.
Please read through these instructions carefully and refer back to them during installation to ensure that your product is fitted safely and that it retains its high-quality finish.
FI#01 036 R210706 Ver No. 1.0 Oct 2021

Warnings for Safe Use

  • This product is intended for Domestic Use only
  • Please read the instructions and warnings carefully before installing the product and ensure this document is kept with the product for future reference to ensure product longevity and in the interest of safety.
  • If you give the product to another person, please give them this manual as well.
  • If any modification is made it will invalidate the warranty and may render the product unsafe.
  • It is not suitable for use in saunas, steam rooms and shower cubicles.
  • When drilling use appropriate eye protection.
  • The use of a Residual Current Device (RCD) is advised for any power tools used during the installation of this product.
  • Take suitable precautions when handling glass.
  • Do not use if glass is broken or unsafe.
  • Beware of hidden cables or pipes. Take care if drilling on tiled surfaces in case the drill slips.
  • It is recommended that this product is installed by a person who is able to meet the level of competence required in order to comply with relevant regulations. If in doubt consult a qualified tradesperson.
  • This product is designed for installation into a brick or masonry block wall, if mounting onto another substrate ensure appropriate fixing and batons (if required) are used and the load bearing of the wall is sufficient.
  • It is recommended that this product is installed by two people.
  • Avoid leaving excessive standing and surface water on the product for prolonged periods of time.
  • Dispose of packaging in accordance to local authority regulations.
  • At end of life dispose of item according to local authority regulations.

We recommend that you place this mirror on a soft flat surface to ensure no breakages. We also recommend that you leave corner protectors on until final fitting.

What’s in the Box?

  • Trim Mirror
  • Fittings pack

Tools Required


It is recommended that this product is installed by two people.

  1. Position the mirror in a suitable location.
  2. Carefully mark the position of the mirror using a soft pencil ensuring it is level.
    Remove the mirror and mark the mounting points, see Fig. 1 overleaf. Please ensure that all marked mounting points accurately match up with the fixing points on the mirror.
  3. Using a suitable drill bit, drill holes in the marked positions to a suitable depth. If drilling through tile, use a ceramic drill bit.
  4. Insert wall plugs level with the surface of the wall. If fitting to a tiled surface, wall plugs should be inserted below the tile surface to avoid cracking. NB.
    For plasterboard walls, specialist fixings should be purchased, available from any DIY or hardware store.
  5. The screw-supplied fixings into wall plugs.
  6. Hang the mirror in position.



To preserve the high-quality finish of your HiB product, please ensure you regard the following care and cleaning recommendations:

  • Use only a soft damp cloth.
  • Wipe off all water spillages as soon as possible.
  • Do not use any abrasives or solvents.


In the unlikely event that this product should fail please contact the retailer from which the item was purchased.
WEEE compliance
Must not be mixed with general household waste

T: +44 (0)20 8441 0352
F: +44 (0)20 8441 0219
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN
©HiB Copyright: No part of this document may be reprinted or duplicated without his consent.
All sizes and measurements are approximate, but we do try and make sure they are as accurate as possible.
In the interest of continuous product development, HiB reserves the right to alter specifications as necessary. E & OE.

Documents / Resources

HiB TRIM Curve, Round [pdf] Installation Guide
TRIM, TRIM Curve, TRIM Round, Trim Curve 40 Black, 62010000, Trim Curve 40 Brushed Brass, 62020000, Trim Curve 50 Black, 62030000, Trim Curve 50 Brushed Brass, 62040000, Trim Round 60 Black, 62050000, Trim Round 60 Brushed Brass, 62060000, Trim Round 80 Black, 62060000, Trim Round 80 Brushed Brass, 62070000


Recent Posts

Inditech 200×1000 Parallel COP DOT Button User Manual

200x1000 Parallel COP DOT Button Product Information The Parallel COP is a sleek and attractive…

2 mins ago

ATD-7320A Truck Ramp Owner’s Manual

ATD-7320A Truck Ramp ATD-7320A Truck Ramps The ATD-7320A Truck Ramps are heavy-duty ramps designed to…

6 mins ago

Inditech 200×1000 Parallel COP Dot Touch User Manual

200x1000 Parallel COP Dot Touch Product Information: The Inditech Parallel COP is a high-precision touch…

14 mins ago

Inditech TFT 170X900 Parallel COP Touch User Manual

TFT 170X900 Parallel COP Touch Product Information: The PARALLEL COP TOUCH TFT panel is a…

34 mins ago

Inditech 75X275 Parallel Lop Touch User Manual

Inditech 75X275 Parallel Lop Touch User Manual TYPE OF MODEL: PARALLEL LOP DOT TOUCH 75x275-12/24V…

36 mins ago

Inditech TFT 75X275 Parallel Lop Touch User Manual

Inditech TFT 75X275 Parallel Lop Touch User Manual TYPE OF MODEL PARALLEL LOP TOUCH TFT…

43 mins ago