Categories: HiB

HiB 79570100 Maxim 50 LED Mirror Instruction Manual

HiB 79570100 Maxim 50 LED Mirror

Electrical Safety Information

HiB recommends that all electrical bathroom products must be installed in accordance with current building and wiring regulations. If in doubt please contact an electrician. Before drilling ensure that there are no hidden cables or pipes in the wall.

Warnings for Safe Use
  • This product is intended for Domestic Use only
  • Please read the instructions and warnings carefully before installing the product and ensure this document is kept with the product for future reference to ensure product longevity and in the interest of safety.
  • If you give the product to another person, please give them this manual as well.
  • If any modification is made it will invalidate the warranty and may render the product unsafe.
  • This product is IP44 rated and suitable for installation in Zones 2 and Outside Zone according to the IEEE regulations.
  • It is not suitable for use in saunas, steam rooms and shower cubicles.
  • Appropriate circuit protection should be available for the product.
  • When drilling use appropriate eye protection.
  • The use of a Residual Current Device (RCD) is advised for any power tools used during the installation of this product.
  • Take suitable precautions when handling glass.
  • Do not use if glass is broken or unsafe.
  • Beware of hidden cables or pipes. Take care if drilling on tiled surfaces in case the drill slips.
  • Always switch off the electrical supply to the product at the mains during installation and maintenance.
  • It is recommended that this product is installed by a person who is able to meet the level of competence required in order to comply with relevant regulations. If in doubt consult a qualified tradesperson.
  • Do not enter IP44 box unless competent and item is isolated from mains.
  • Do not use if any electrical wires appear damaged or degraded.
  • This product is designed for installation into a brick or masonry block wall, if mounting onto other substrate ensure appropriate fixing and batons (if required) are used and the load bearing of the wall is sufficient.
  • It is recommended that this product is installed by two people.
  • Avoid leaving excessive standing and surface water on the product for prolonged periods of time.
  • Dispose of packaging in accordance to local authority regulations.
  • At end of life dispose of item according to local authority regulations.

We recommend that you place this mirror on a soft flat surface to ensure no breakages. We also recommend that you leave corner protectors on until final fitting.
Do not lift this product via the illuminated frame.

Electrical Information

This product contains a light source of energy efficiency class E

This product is IP44 rated and is suitable for installation in zones: 2 & Outside Zone

All installations must comply with guidelines which are based on a zonal concept and must be followed to ensure the safe installation of electrical appliances in the bathroom.
These regulations apply to domestic installations only. Installations must be made in accordance with the current IEE wiring regulations and relevant building regulations.

Wiring Diagram

What’s in the Box?

  • Maxim Mirror
  • Fittings pack
Tools Required



It is recommended that this product is installed by two people.

  1. Position the mirror in a suitable location according to the zonal diagram – Fig. 1, ensuring that the domestic electrical mains supply is within reach of the cable connection point of the product.
  2. Carefully mark the position of the mirror using a soft pencil ensuring it is level. Remove the mirror and mark the mounting points, see Fig. 2. Please ensure that all marked mounting points accurately match up with the fixing points on the mirror.
  3. Using a suitable drill bit, drill holes in the marked positions to a suitable depth. If drilling through tile, use a ceramic drill bit.
  4. Insert wall plugs level with the surface of the wall. If fitting to a tiled surface, wall plugs should be inserted below the tile surface to avoid cracking. NB. For plasterboard walls, specialist fixings should be purchased, available from any DIY or hardware store.
  5. Screw supplied fixings into wall plugs.
  6. Ensure the domestic electrical mains supply to which the mirror is being connected is turned off. Connect the domestic mains supply to the terminal box according to the wiring diagram, see page 3.
  7. Hang the mirror in position.
  8. Switch the domestic electrical mains supply for the mirror back on.


To switch on/off
  1. Wave hand past the sensor switch located on the mirror face, see Fig. 3.
  2. Heated pad is on when the mirror is illuminated.

To change the colour temperature

  1. Hold hand in front of the sensor switch until desired colour is obtained.
  2. The colour temperature is then set until changed again.


To preserve the high quality finish of your HiB product, please ensure you regard the following care and cleaning recommendations:

  • Use only a soft damp cloth.
  • Wipe off all water spillages as soon as possible.
  • Do not use any abrasives or solvents.

In the unlikely event that this product should fail please contact the retailer from which the item was purchased.

WEEE compliance
Must not be mixed with general household waste

T: +44 (0)20 8441 0352 F: +44 (0)20 8441 0219 E:
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN
©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and make sure they are as accurate as possible. In the interest of continuous product development, HiB reserves the right to alter specifications as necessary. E & OE.

Documents / Resources

HiB 79570100 Maxim 50 LED Mirror [pdf] Instruction Manual
79570100, Maxim 50 LED Mirror, 79570100 Maxim 50 LED Mirror, 79570200, 79570300


Recent Posts

Mimaki CG-60AR Vinyl Cutter Instruction Manual

CG-60AR Vinyl Cutter Product Information The CG-60AR is a product that requires assembly of its…

5 mins ago

HILTI Heli-Brick Helical Bar Installation Guide

Heli-Brick Helical Bar Product Information The Heli-Brick is a product used for installation and connection…

6 mins ago

HOBO MX2300 External Temperature/RH Sensor Data Logger User Manual

MX2300 External Temperature/RH Sensor Data Logger Product Information The HOBO MX2300 Series Data Logger is…

6 mins ago

Haier ADH200H1ERG High Static Ducted User Guide

ADH200H1ERG High Static Ducted Product Information The ADH200H1ERG is a high static ducted air conditioning…

8 mins ago

UniFi AX1800 WiFi 6 Router User Guide

AX1800 WiFi 6 Router Product Information: The Unifi TV Media Box and Wi-Fi 6 Router…

8 mins ago

AURA VENOM-D2.1 500 2 Channel Stereo Power Amplifier Owner’s Manual

VENOM-D2.1 500 2 Channel Stereo Power Amplifier

9 mins ago