ion4i Access Point
User Guide
Introduction
Thank you for choosing ion4i Wireless Access Point with 22.2 Multi-User MIMO and 802.11ac Wave 2 compliance.
Packaging Content
ion4i Specifications
| Peak Throughput(aggregate) | Up to 1.27 Gbps (867 Mbps for 5 GHz and 400 Mbps for 2.4 GHz) |
| Wi-Fi Standard Support | 802.11 a/b/g/n/ac/ac Wave 2 |
| Interface | 1 X 10/100/1000 BASE-T Ethernet |
| Radio Mode | 2×2 MU-MIMO with 2 spatial streams |
| Mesh Support | Self-creating, Self-healing Mesh |
| Maximum number of SSID (per radio) | 16 |
| Maximum User Support | 128 on 5 GHz and 64 on 2.4 GHz |
| Power Supply | IEEE 802.3af PoE |
| Power Consumption (Max) | 12 W (approx.) |
| Max Transmit Power | 23 dBm for 2.4 GHz, 27 dBm for 5 GHz (will depend on country specific guidelines) |
| Antenna Type | Integrated Omnidirectional Antennas |
| Antenna Gain | 4.5 dBi for 5 GHz, 4 dBi for 2.4 GHz |
| Management | Standalone (via GUI) or through on-premise based solution or cloud-based |
| Enclosure Dimensions | 175 x 175 x 37 mm or 6.89 x 6.89 x 1.46 inches |
| Weight | 0.35 kg |
| Operating Temperature | 0°C to 50°C |
| Certifications | FCC Class B, CE, Passpoint 2.0, RoHS 3.0 |
Product Overview
Mounting of ion4i Access Point
- Place the Mounting Bracket which came with the package on a wall or ceiling and mark holes with a marker where you will insert the screws. Drill holes in the marked points and insert the plastic wall anchors.
- Use supplied screws and attach mounting bracket on the wall
Note Make sure that mounting bracket is tightly installed before mounting the Access Point on the wall or ceiling.
- Align the hooks of Access Point with the mounting slots of the mounting bracket, ensure that it is properly hinged
Unmounting of ion4i Access Point
- Slide the hooks of Access Point out from the mounting slots of mounting bracket.
WARNING: HFCL is not held liable for any damages incurred during the process.
Getting the ion4i Online
Step 1: Power up
The Access Point can be powered up using PoE adaptor (48V) as shown below:
Note: Plug and Adaptor will vary by country/ region
Step 2: Connect to the network
Section 1: Standalone AP
Follow the steps mentioned below and connect the Access Point to a network
- Connect an ethernet cable to the computer.
- Connect the other end of the ethernet cable to the LAN port on the ion4i Access Point or use a PoE adaptor (48V) to do so.
- Open the web browser and enter the Access Point static IP address in the address bar. 192.168.1.1
- A login screen will appear
Enter the default login credential details:
User- root, Password- hfcl!@ion
Section 2: Controller Managed AP
Follow the steps mentioned to connect Access Point to a network
- Connect an Ethernet cable to the computer
- Power-up the AP through PoE adapter or PoE switch
- Connect the AP to DHCP network and Internet
- Login to HFCL 10 cloud controller (cNMS) iocloud.hfcl.com with credentials provided
4a. To get cNMS login credential, please send request email to iosupport@hfcl.com with below detailsCustomer Name Customer email address Customer address Customer contact number Distributor/ Retailer Name No.of AP Purchased Country - Add AP group under configuration
- Add APs in the AP group
- Create SSID in the AP group
- Refer our website io.hfcl.com for detailed information to configure AP through cNMS
Step 3: Check the LED status
| LED Color | Status |
| Power LED Green | Green color notifies the user that the device is powered ON |
| 2.4 GHz Status LED | Solid yellow color notifies the user that the 2.4 GHz radio is active and blinks while data is being transmitted on 2.4 GHz radio |
| 5 GHz Status LED | Solid red color notifies the user that the 5 GHz radio is active and blinks while data is being transmitted on 5 GHz radio |
Safety Precautions
Observe the following safety precautions to avoid damage to the ion4i Access Point:
Do not subject the device to high temperaturesKeep away from high voltage cablesDisconnect the device before cleaning itDo not wipe the device with a damp clothDo not open the enclosure of the Access PointFasten the device tightly with the mount
Part Number QSG-01-0016
Revision: A
Contact Us:
Email: iosupport@hfcl.com
Website: www.hfcl.com
wwwio.hfcl.com
8, Commercial Complex, Masjid Moth,
Greater Kailash-II, New Delhi- 110048
HFCL Limited All Rights Reserved.
IO Networks and the IO logo are registered trademarks of HFCL Limited
Specifications are subject to change without notice
Documents / Resources
 | HFCL ion4i Access Point [pdf] User Guide ion4i Access Point, ion4i, Access Point |
 | HFCL ion4i Access Point [pdf] User Guide ion4i Access Point, ion4i, Access Point |
 | HFCL ion4i Access Point [pdf] User Guide ion4i Access Point, ion4i, Access Point, Point |
