HERITAGE Flat Bottom Instructions

HERITAGE Flat Bottom

Specifications:

Product Name: Flat Bottom Barrel
Model: N/A
Material: N/A
Color: N/A
Dimensions: N/A

Product Usage Instructions

Assembly:

Follow these steps to assemble the flat bottom barrel:

Ensure all components are provided.
Connect the flat bottom to the barrel securely.
Check for any leaks or loose fittings before use.

Filling the Barrel:

To fill the barrel with your desired content, follow these steps:

Open the top lid of the barrel.
Pour the contents carefully into the barrel.
Avoid overfilling to prevent spillage.

Usage:

Once assembled and filled, use the flat bottom barrel as follows:

Place the barrel on a flat surface.
Handle with care to avoid damage.
Follow specific instructions for the intended use of the barrel.

Frequently Asked Questions

Q: How do I clean the flat bottom barrel?

A: To clean the barrel, empty any remaining contents, rinse with warm water, and let it air dry completely before reuse.

Q: Can I use the flat bottom barrel for hot liquids?

A: It is recommended to check the product specifications for temperature limits. Avoid using the barrel for liquids exceeding those limits.

Q: Is the flat-bottom barrel dishwasher safe?

A: Refer to the product manual for cleaning instructions. Some barrels may be dishwasher safe, while others require handwashing.

Assembly INSTRUCTIONS

Floor base. On level surface screw 5 long boards with the 2 56″ end boards
screws into each board
Lay floor boards on and start at one end and screw it down. Keep floor boards as tight together as possible
2 screws into each floor base. Leave Center long board with no screws. Walk isle area.
No screws in Center isle way.
Use a clamp to pull boards together if needed
Lay a left stave and right stave on each side
Lay front wall door pc on floor
Screw staves to front wall section
Screw both sides
Do same with first pc in back wall.
Put board tight to wall and fasten with 1 screw.
Front wall and back wall should over hang floor at both ends
Screw down floor cleats then push down on wall board so it’s tight to floor then put in the 2 pocket screws.
Levels sauna to floor and now secures it.
Put in long floor cleats and screw down into floor and into staves
Make sure to put screw to inside so not to miss floor frame
Insert door with hinges to right
Insert both front wall pcs
Screw wall together with a 4″ screw
Put top pc of wall over door and fasten with 4″ screws
Put a total of 4 staves on each side now and fasten into wall
Using bench height measuring sticks fasten Ben h support cleat
Both benches should now be in
Add next back wall portion and fasten with 4″ screws
Put more staves on at this point.
Add rest of back wall and fasten with 4″ screws
Put staves on and fasten on. Leave the last 8 staves unscrewed to allow putting in the top stave
Set top stave in and then close up staves tight. Screw all staves down with screws now
Should now look like this
Put roof membrane over and make it even down both side. Staple over front staves
Cut off excess plastic
Attach barge boards. Center top one and fasten on.
Use 3 screws in each one
Do same process for back barge boards
Makes a nice water seal to allow water run off.
Put neoprene strips over and 6″ away from barge boards
Screw through strip on both sides to hold it in place
Vent is Center. Put 1/4″ space between top 2 roof boards on Center.
When attaching roof boards make sure screw goes through neoprene strip for water seal
Keep ends even with barge boards to look nice
About 1/4″ spacing between roof boards
Trim excess plastic off
Fasten door handle about 21″ from top of door
Fasten inside door handle middle of outside handle across door
Inside door handle
Attach clothes hook
Fasten back rest with screw into pre drilled holes
Put in headrest
Finished