ZigBee Smart plug
Palapala Hoʻohana

Hoʻolauna Huahana

ʻO ke kaumaha o ka mea ma lalo o 1 kg. Manaʻo ʻia ke kiʻekiʻe o ka hoʻokomo ʻana ma lalo o 2 m.

Nā kuhikuhi hoʻonohonoho

1. Paʻa ka mana No ka pale ʻana i nā haʻalulu uila, e ʻoluʻolu e nīnau i ka mea kūʻai aku a i ʻole kekahi loea kūpono no ke kōkua ke kau ʻana a hoʻoponopono.
2. Aʻo uea
   E hōʻoia i ka uwea pono ʻana ma mua o ka hoʻā ʻana i ka hāmeʻa. S1/S2 can connect with the rocker light switch, or it doesn’t connect. To ensure safety, do not connect the neutral wire and live wire to it.

Nā kikoʻī

Nā hiʻohiʻona

ZigBee plug is a smart Plug that adopts the ZigBee plug wireless protocol and connects to your internet through the ZigBee hub. You can turn on/off, schedule on/off, and share the device with your family to control together, and so on.

Mana mamao	Hōʻike manawa
Mana Leo	Māhele Māhele
ʻĀina Manaʻo

The above functions are determined by the ZigBee Hub.

Aʻo hana

1. Hoʻoiho i ka APP
   Please refer to the user guide of the hub to download the corresponding APP. below platforms are recommended:

   Nā mea akamai	Amazon Alexa	Hue

2. Hoʻohui Hub
   Set the hub according to the user guide. Support ZigBee plug hubs as follows:
   Echo Studio
   Echo Plus (ke kumu hoʻohālike: ZE39KL)
   Hōʻike Echo Generation 2 (ke kumu hoʻohālike: DW84JL)
   2nd Gen Echo Plus (ke kumu hoʻohālike: L9D29R)
   ʻO Samsung SmartThings hub
   Philips Hue
   Inā hāʻule ka pilina, e ʻoluʻolu e hoʻoneʻe i ka hub kokoke i kāu kelepona a hoʻāʻo hou.
3. Ka mana
   Ma hope o ka hoʻā ʻana, e komo ka hāmeʻa i ke ʻano pairing i ka wā o ka hoʻohana mua ʻana, a ʻālohilohi ka hōʻailona hōʻailona LED.
    The device will exit the pairing mode if no next operation for a long time. If you enter again, please long-press the manual switch for 5s until the LED signal indicator flashes and release.
4. Hoʻohui iā Alexa
   1. Power on the Plug
   2. Ask, “Alexa, discover devices!
   3. Plug ashes once it’s connected
   4. Wait until Alexa finishes, check the new devices” First/Second….plug”

Hoʻohui iā SmartThings

1. Power up the smart bulb, bulb breathe 3 times, and enter the configuration state.
2. Open the SmartThings app, and click”+”, click “Device”, click “SmartThings”, click “Lighting”, click ” Smart Bulb”, click “Start”, click “Next”, click “Skip the step”, click “Done”

Hana Hou

Long-press the configuration button for 5s until the LED signal indicator flashes and release, then the reset is successful. The device enters spairing mode.

If you pair the device with the hub again, please reset the device to factory default.

Hana ʻia ma Kina

Palapala / Punawai

ZigBee Light Switch Module [pdf] Palapala Hoʻohana Light Switch Module, Switch Module, Module

Nā kuhikuhi

• Palapala Hoʻohana