ColorKey | Club & DJ Lighting
User Manual for ColorKey models including: CKU-5038, Mover Halo Beam QUAD MKII, CKU-5038 Mover Halo Beam QUAD MKII, Halo Beam QUAD MKII, Beam QUAD MKII, QUAD MKII, MKII
Mover Halo Beam QUAD MKII - ColorKey
File Info : application/pdf, 9 Pages, 1.35MB
DocumentDocumentMover Halo Beam QUAD MKII CKU-5038 USER MANUAL Introduction Thank you for purchasing the ColorKey Mover Halo Beam QUAD MKII. Please read these instructions carefully before use. Operating this fixture according to these instructions is important to avoid any possible damage or accidents caused by misuse. Packing list n 1x Mover Halo Beam QUAD MKII moving head fixture n 1x Bracket n 1x Power cord n User Manual Safety Caution! Opening this unit voids warranty. Contact ColorKey for any service requests. Warning! To avoid electrical shock, be sure to disconnect power before any service or when moving or setting up the fixture. Caution! Avoid direct eye exposure with the fixture when on. · This fixture is for indoor use only. · This fixture must be installed a minimum distance of 5 meters (16'4") away from any lighted objects. · Do not install or operate this fixture near flammable materials. · This device must be installed, operated, and maintained by a qualified professional. · Do not touch the fixture with bare hands during operation as the surface temperature of the fixture can exceed 60°C (140°F). Turn off power and wait 15 minutes for the fixture to cool before attempting to touch it. · Please check if the voltage is in accordance with the rated power before installing. · Do not operate this fixture if the power cord has been damaged. Turn off fixture and replace with a power cord of similar rating. 1 Display Operation Ø MENU: Access the menu/Scroll through menu options Ø ENTER: Open/Select the current menu option Ø UP: Scroll through menu selection or parameter increase Ø DOWN: Scroll through menu selection or parameters decrease 2 Menu Guide Addr CHnd SLnd A001A512 16CH 14CH Auto Soun SL 1 SL 2 Menu Guide DMX512 address 16channel setting 14channel setting Auto mode(master) Sound mode(master) console mode slave mode ID ID00-ID15 ID setting SHnd SH 0 SH 1 SH 2 SH 3 effect 0 (recommended) effect1 effect2 effect3 SEnS 0-99 Sensitivity adjustment bLAnd bLAc Auto Soun HoLd 0(no DMX signal) Auto mode(no DMX signal) Sound mode(no DMX signal) stays on the latest console scene(no DMX signal) LEd OFF ON Display turns off after 5 seconds Display stays on dISP no YES Display Up Display Down rPAN no YES Forward rotation (PAN) Backward rotation (PAN) rTiL no YES Forward rotation (TILT) Backward rotation (TILT) REST YES System reset 3 DMX Values 16 Channel Mode Channel Value 1 0-255 2 0-255 3 0-255 4 0-255 5 0-255 6 0-255 7 0-255 8 0-255 9 0-255 10 0-255 11 0-255 12 0-255 13 0-255 14 0-255 15 0-255 16 250-255 Function Pan (Coarse) Pan (Fine) Tilt (Coarse) Tilt (Fine) Rotation Speed Dimmer Strobe Red dimming Green dimming Blue dimming White dimming Color chase Ring Color / Chasing Effect Auto (motor: Pan/Tilt) Chase speed Reset (5seconds) 14 Channel Mode Channel Value 1 0-255 2 0-255 3 0-255 4 0-255 5 0-255 6 0-255 7 0-255 8 0-255 9 0-255 10 0-255 11 0-255 12 0-255 13 0-255 14 250-255 Function Pan (Coarse) Tilt (Coarse) Rotation Speed Dimmer Strobe Red dimming Green dimming Blue dimming White dimming Color chase Ring Color / Chasing Effect Auto (motor: Pan/Tilt) Chase speed Function 4 DMX Connections Ø DMX Cable This fixture can be controlled via DMX using a 3-pin XLR connection. The standard DMX connection is XLR is: one end connects to the male plug, and the other connects to the female. As below: pin 1: ground, pin 2: negative signal, pin 3: positive signal NotedIn order to avoid failures and interference signal transmissionwe connect a resistance1201/4Wat the end of the DMX connecting as below: Ø The Conversion between 3 pin and 5 pin XLR If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to 3PIN cable 5 Master/Slave Mode Operation Master/Slave Master/Slave mode allows you to connect multiple units together using one (1) unit to control others in a chain. When a fixture is set to `Master Mode,' this unit will always act as a controlling unit until it is switched out of `Master Mode'. The Master unit will send out signal via DMX to Slave units which will react in synchronization. When a fixture is set into `Slave Mode', this fixture will receive the Master signal. To avoid master signal and DMX signal interference, do not connect DMX when using Master/Slave mode. If using a DMX run longer than 60 meters and/or over 32 units, a signal amplifier may be required. ***Please note that Mover Halo Beam QUAD MKII will only work with other Mover Halo Beam QUAD MKII models and not the first generation model.*** Troubleshooting Problem No DMX control Solutions u Make sure that the DMX cable is properly connected u Make sure that the DMX controller is operational u Check the DMX cable for tears or breaks u Make sure that the fixture is in DMX mode Fixture does not respond to sound u Make sure that the fixture is in Sound Active mode. 6 Technical Information Beam: 40W RGBW 4-in-1 LED Ring: 12x 5050 RGB 3-in-1 SMD LEDs Independent DMX control of beam and ring effects Beam angle: 8° Built-in auto/sound active programs Digital dimmer and strobe Pan: 540° Tilt: 270° Pan/tilt invert 16/30 channel DMX modes Power consumption: 70W Working Environment: Indoor, -4°F to 104°F (-20 to 40) IP Grade: IP20 Power Supply: AC 100-240V/50-60Hz 3-pin DMX connections IEC power connection Size: 11.4"x8.25"x8.25" (29x21x21 cm) Weight: 6.6 Lbs. (3kg) Notice to consumer: ColorKey offers a 2-year limited warranty. Please visit our website at www.ColorKeyLED.com to register your product. Please note: We recommend that you check our website periodically for updates to user manuals and specifications at www.ColorKeyLED.com or you may contact us directly at info@colorkeyled.com. 7 8