Palapala

HUNTER-logo

HUNTER Klein 19440 Light Pendant

HUNTER-Klein-19440-Light-Pendant-product

maluna oview

HUNTER-Klein-19440-Light-Pendant-fig-1

NA OLELO HOAKAKA

Aʻo 

  • No ka pale ʻana i ka haʻalulu uila, ma mua o ka hoʻokomo ʻana i kāu mea uila, e kāpae i ka mana ma ka hoʻopau ʻana i nā mea haki kaapuni i ka pahu puka e pili ana i ka wahi hoʻololi o ka paia.
  • Pono e hoʻokumu i nā kukui. Inā ʻaʻohe ka uea lepo no ka pūnaewele hoʻonohonoho, e hoʻopau koke iā STOP a nīnau i kahi uila uila kūpono.
  • Pono nā pilina uila āpau e like me nā wae uila a kūloko kūloko ANSI / NFPA 70. Inā kamaʻāina ʻole ʻoe i ka uea ʻana a i ʻole kānalua, e nīnau i kahi uila pono.

HELUHELU A HOOPAKELE I KEIA MAU OLELO
Hāʻawi ʻia kēia mau kuhikuhi no kou palekana. He mea nui e heluhelu akahele ʻia a ma mua hoʻi o ka hoʻomaka ʻana o ke kau ʻana i nā kukui.

Eia nā mea hana e pono ai ʻoe e hoʻopau i kāu kau ʻana

HUNTER-Klein-19440-Light-Pendant-fig-3

E hoʻomākaukau ana no ka hoʻouka

Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture. Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. One end of the threaded post (H) should be attached to the mounting bracket (A) with a hex nut (G) in place. The other end should be connected to the canopy loop (E). Unscrew the canopy loop ring (F) from the canopy loop (E). Depending on the placement of your junction box the position of threaded post (H) may need to be adjusted to allow the canopy to be flush with the ceiling. Determine this by lifting mounting bracket (A) up to the junction box and place canopy (D) over the canopy loop (E), so that it is flush with the ceiling. Adjust the position of threaded post (H) on the mounting bracket (A) so that the canopy (D) covers at least half of the exterior threads on the canopy loop  (E) while it is securely connected to threaded post (H). The threaded post (H) can be adjusted by loosening hex nut (G) to allow movement of threaded post (H) on mounting bracket (A). Once the ideal position of the threaded post (H) is determined, tighten up the hex nut (G) onto the threaded post (H) just beneath the mounting bracket (A) to secure the threaded post in place..

KA HUI ANA I KA HANA

There are 4 12-inch rods (I), and 1 6-inch rod (J) included for each fixture. Determine the correct number of rods needed for proper hanging height. To lengthen the fixture, add additional rods. To shorten the fixture, trim the wires to desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the fixture’s wiring to discard. Keep in mind that you must use at least one rod to hang the fixture. Thread the wires through the rods and pull the wires until taut before connecting the rods together. Screw rod onto threaded post (K) on the fixture. Pull the fixture wires through the canopy loop ring (F), top of canopy (D), and canopy loop (E). Screw the top rod to canopy loop (E). Have a helper support the fixture’s weight and attach the mounting bracket (A) to the junction box by securely tightening the mounting screws (B).

HUNTER-Klein-19440-Light-Pendant-fig-2

KAUOHA ANA I NA KAUA 
E hoʻopili i nā uea o ka mea hoʻopili i nā uwea lako mana mai ka pahu hui. Hoʻohui ʻeleʻele i ka ʻeleʻele (Live); keʻokeʻo a keʻokeʻo (grounded); hoʻopaʻa ʻia i ka lepo ('ōmaʻomaʻo a keleawe paha). E wili pu i na welau o na uwea. A laila, wili ma kahi mea hoʻohui uea. E hōʻoia i nā wili a pau ma ke ala like. E hoʻopaʻa i ka uwea lepo o ka mea hoʻopili a puni ka wili lepo (C) a hoʻopaʻa. Inā ʻaʻohe uea honua ('ōmaʻomaʻo a keleawe paha) mai ka pahu hui, e hoʻopili i kahi uila uila

E HOPE ANA I KA INSTALLATION

Place the canopy (D) flush to the ceiling and slide the canopy loop ring (F) up beneath the canopy. Tightly screw canopy loop ring (F) onto the canopy loop (E) to properly secure the canopy (D) in place. Carefully install glass shade (M) over socket (L), then install socket cover (N) and tighten up the glass shade with socket ring (O). Install light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Ua pau kāu hoʻouka ʻana. E ho'ā i ka mana a ho'āʻo i ka mea paʻa.

OLELO HOOMAEMAE

E mālama mālie i nā mea paʻa! ʻO ka hoʻomaʻemaʻe maʻamau e hōʻemi i ka pono no ka hoʻomaʻemaʻe hohonu. No ka hoʻomaʻemaʻe maʻamau, hoʻopau i ke kukui a holoi i ka paʻa me kahi lole lint-free maʻemaʻe a i ʻole lole microfiber. Mai pīpī i ka mea hoʻomaʻemaʻe ma luna pono o ka uila.

HOʻOMAOPOPO
In order to use a 12in rod by itself you must first remove the post from the 6in rod and install it on one of the ends of the 12in rod

Manaʻo kōkua Hunter Pro 
Twist or tape wire ends together to make it easier to pass them through the downrods. Threaded post may also be removed for easier wire access

Palapala / Punawai

HUNTER Klein 19440 Light Pendant [pdf] Palapala Aʻo
Klein 19440, Klein, 19440, Light Pendant

Waiho i ka manaʻo hoʻopuka

Ko oukou mail aae? E, aole e paʻiʻia.