X1 Combo 3D Printer
User Guide
X1 Combo 3D Printer
*Safety Notice: Do not power on the printer before installation is complete.
Please refer to this guide to complete the installation and printing of the printer.
HALOT-X1 Component Introduction
List of Accessories
HALOT-X1 Quick Start Operation Schematic
Lift upward to remove protective corner pads and packaging materials; Remove the power cable, Quick Start Guide, and accessory tray.
Video Tutorial
https://drive.google.com/drive/folders/1NofDOxZITe-CpKi3P5oiqCGidBaV9aKq?usp=sharing
HALOT-X1 Quick Start Operation Schematic
Remove the tape between the transparent cover on both sides of the device and the base.
Remove the top black foam before the white foam.
Install the printing platform along the slot.
Connect the power cable and switch on your HALOT-X1.
HALOT-X1 First Printing
A (pour resin into the resin vat) or
B (let AFU manage the resin feed).
*HALOT series resins are recommended for the first print.
Tap “Print” on the home page.
Select the pre-sliced file stored in the device.
Click “Print” to start the first print.
HALOT-1� Networking, Access to the Cloud
In the main interface of the device, go to “Settings” → “System Settings” → “Wi-Fi”, select the Wi-Fi you want to connect to, and network the device.
Install the “Creality Cloud” app on your smartphone → Register an account;
In the main interface of the device, go to “Settings” → “System Settings” → “Creality Cloud”, and use the Creality Cloud app to scan the code to bind the device.
Software Installation
Download the installation package from www.piocreat9d.com Read the installation package from a random USB flash drive
HALOT-X1 Technical Specifications
HALOT-X1
| Body Parameters | Build Volume (L×W×H) | 211.68mm×118.37mm×200mm |
| Product Dimensions | 344mm×331mm×434mm | |
| Package Dimensions | 430mm×420mm×535mm | |
| N.W. | 12.93kg | |
| G.W. | 16.19kg | |
| Printing Parameters | Printing Technology | LCD |
| Light Source | Honeycomb Matrix Light Source | |
| Exposure Intensity | 6500±10%μW/cm² | |
| Resolution | 16K（15120*6230px） | |
| Pixel Size | 14*19μm | |
| Z-axis Positioning Accuracy | 0.01mm | |
| Layer Thickness | 0.01~0.2mm | |
| Printing Speed | Max.170mm/h（0.2mm Layer thickness） | |
| System Parameters | Touch Screen | 3.98-Inch Capacitive Touch Screen |
| Slicing Software | HALOT BOX/Chitu Box | |
| Data Transmission | USB/WIFI | |
| Input Voltage | 100-120V~200-240V~, 50-60Hz | |
| Power | 350W |
AFU Component Introduction
List of Accessories
AFU Quick Start Operation Schematic
Turn the mount down and the snap ring up.
https://drive.google.com/drive/folders/1EeC53ylXCq2omcrkRZ2vYyiHnDEsitAO?usp=drive_link
AFU Quick Start Operation Schematic
Connect the extrusion feed hose and Type C control cable to the AFU I/O port on the printer.
A. Vertically insert the suction tube into the adapter cap port
B. Place resin bottle into the mounting base
C. Tighten adapter cap with clockwise rotation
D. Press-rotate the feed hose connector into the adapter cap inlet port.
After removing the material tank:
A. Loosen the fastening screws of the fixed slot and disassemble the fixed slot assembly.
B. Install the detection module bracket at the original position of the fixed slot.
Install the detection module onto the bracket and press it down until the buckle makes a “click” sound.
A. Vertically insert the feeding hose into the feeding port of the detection module.
B. Vertically insert the control cable into the wiring port of the detection module.
AFU First Use
Inspect the installation of the feeding resin bottle; 
Remove the detection module from the bracket and install it on the fixed position of the material tank.
Press it down until the buckle makes a “click” sound.
Manual control of the feeding module of the device:
Main interface → Settings → Feeding module
Automatic control of the feeding module of the device: Main interface → Printing → On the file information interface or the printing interface, click the “Automatic feeding” button to start automatic feeding at any time.
Note: If the printer page can access the “Feeding Module”, it means that the AFU has been accessed, If it cannot access the“Feeding Module”, then check the wiring connection; if the resin bottle has an RFID chip, the page display will show the “ 
” logo, which can display the resin balance;
IC ID Requirement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference;
- This device must accept any interference, including interference that may cause undesired operation of the device.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
FCC Requirement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference;
- This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Please visit the PioCreat website for more machine operation and maintenance tutorials.
Note： The UI interface is only for reference, and shall be subject to the actual UI.
Enjoy!
https://linktr.ee/qr/2e8bd295-e61c-4c7f-984b-cfad0d17f62c?utm_source=qr_code
Documents / Resources
 | HALOT X1 Combo 3D Printer [pdf] User Guide X1, X1 Combo 3D Printer, Combo 3D Printer, 3D Printer, Printer |