Zykronix Symphony XL 11.6 inch Touch Panel Jagorar Shigarwa

Zykronix Logo

Symphony XL

Kunshe a cikin akwati

  • 1ea Device
  • 1ea Mounting bracket
  • 4ea Mounting screws

Gabatarwa

To install the device you will also need one of the following electrical junction boxes or low-voltage brackets.

Electrical Junction Boxes

Muhimman umarnin aminci

Read, understand and follow ALL safety and installation instructions included in this manual. Failure to follow the included documentation may damage the product and will void the manufacturer’s warranty. Follow ALL installation guidelines included with the product. Installation of the product in high humidity environments, in close proximity to heat sources and/or non-recommended locations WILL impede, interfere and/or damage the intended operation of the product. Only use attachments and accessories which have been specified for use by the manufacturer. The use of abrasive, liquid or solvent-based cleaning fluids WILL damage the product. Product Servicing may ONLY be completed by authorized or certified service centers & personnel. For a complete list of product servicing options, please follow instructions included in the product documentation and/or contact the original manufacturer for details.

An gwada wannan kayan aikin kuma an gano sun bi ƙa'idodi don na'urar dijital Class B, bisa ga sashi na 15 na Dokokin FCC.

Waɗannan iyakokin an tsara su ne don samar da kariya mai ma'ana game da tsangwama mai cutarwa a cikin shigarwar mazauni. Wannan kayan aikin yana haifar, amfani kuma zai iya haskaka kuzarin mitar rediyo kuma, idan ba'a shigar dashi kuma anyi amfani dashi daidai da umarnin, na iya haifar da tsangwama mai cutarwa ga hanyoyin sadarwa na rediyo. Koyaya, babu tabbacin cewa tsangwama ba zai faru a cikin takamaiman girkawa ba. Idan wannan kayan aikin ya haifar da tsangwama mai cutarwa ga rediyo ko karɓar talabijin, wanda za'a iya tantance shi ta hanyar kashewa da kunnawa, ana ƙarfafa mai amfani da ƙoƙarin gyara tsangwama ta ɗayan ko fiye daga cikin waɗannan matakan:

  • Maimaitawa ko sauya eriyar karɓa.
  • Theara rabuwa tsakanin kayan aiki da mai karɓa.
  • Haɗa kayan aikin a cikin wata mashiga ta kan hanya daban da wacce aka haɗa mai karɓar.
  • Tuntuɓi dillalin ko gogaggen ma'aikacin rediyo / TV don taimako.

Device – Overview

Overview

Note: Only Symphony XL equipped with hue lights.

Shirya shigarwa

The device is designed to be wall mounted in either Portrait or Landscape orientation, or on tabletop with stand.

Shirya shigarwa

Shigar da na'urar

Shigar da na'urar

A. Mounting height

The recommended mounting height for the device is 57”- 65” (145 cm -165 cm) from the finished floor to the center of the unit.

B. Landscape/Portrait mounting

Device can be mounted and oriented in Portrait or Landscape.

C. Installing the device mounting bracket

The device package includes a stainless steel mounting bracket that MUST be used for installation. Please note the mounting bracket in the box is designed for the US standard 2-gang and supplied Arlington mounting ring supplied in the box. You can order additional stainless steel mounting brackets for UK or European electrical boxes. Verify that the bracket is level before tightening the captive screws on the device. (US mounting bracket included in the box)

Installing the device mounting bracket

D. Connecting the device to power

The device is designed to be powered over the Ethernet connection (PoE) or by connecting a 24Vdc power supply (not included), but not both. If both the PoE and a 24Vdc power supply are connected, the device will draw power from the 24V DC source.

Haɗin PoE

PoE connection requires IEEE 802.3af standard. Utilize a network switch or PoE injector that meets this standard. Connect the device using a standard T568A or T568B Ethernet cable from the network switch to the LAN/PoE jack on the back of the device.

Haɗin PoE

24V DC Supparfin Wuta

You can provide power locally or remotely to device by utilizing a 24V DC power supply (not included). Please note that running the wire through the wall in accordance with local codes when powering locally. If powering remotely, please ensure to use wire of adequate gauge for the length of the run. Please use approved 24V DC power supply.

Verify the polarity of the barrel connector on your power supply before connecting it to the device. The center pin of the device power connector is positive and the outer ring is negative. If the wire is extended, please ensure that the routing is in compliance with local codes.

Plug the connector into the device DC jack on the back of the device.

Plug the connector into the device

Powering up the device

Powering up the device

The device will automatically power on when power is applied. Wait for the unit to boot up. When it’s connected to a network switch by Ethernet cable, the device will acquire a network address via DHCP and automatically connect to the system.

Temperature ranges/humidity

Zafin jiki

E. Mounting the device

  1. Loosen the captive screws of the unit first. Screws should not be moved apart from the unit. Please meet the indicated line.
  2. Align the mounting frame hooks with the mounting slots and gently pull the unit down the mounting bracket. Make sure the mounting hooks are properly engaged.
  3. To complete the installation, tighten the 2-captive screws on the bottom part of unit, to secure the device on the mounting bracket.
  4. For Portrait orientation, rotate mounting bracket and 90 degrees in counterclockwise direction before installation.

Haɗa na'urar

Cire na'urar

Using a precision Philips head screw driver to loosen the 2-captive screws on the device, then slightly pull straight up from the mounting frame to disengage the unit.

Cire na'urar

Setting screen orientation

On the touch panel setup screen, select Landscape or Portrait display modes. Press Start device to launch the user interface.

To change orientation:

Setting screen orientation

  • Remove power from device.
  • Re-apply power to device.
  • Select landscape or portrait orientation.

Thank you for including the device as part of the user interface strategy for your customer. The device has been designed to provide years of trouble free operation when wired and installed properly. The device is designed for installation in low humidity indoor environments and should never be installed outdoors or in high humidity areas.

Duk wani canje-canje ko gyare-gyare da ba a ba da izini ga mai ba da wannan na'urar ba zai iya ɓata ikon mai amfani da shi don sarrafa kayan aikin.
Wannan na'urar tana aiki da Sashe na 15 na Dokokin FCC. Aiki yana ƙarƙashin sharuɗɗa biyu masu zuwa: (1) wannan na'urar bazai haifar da tsangwama mai cutarwa ba, kuma (2) wannan na'urar dole ne ta karɓi duk wani tsangwama da aka karɓa, gami da tsangwama da zai iya haifar da aikin da ba a so.

Gargadin fallasa RF
Dole ne a shigar da wannan kayan kuma a yi aiki da su daidai da umarnin da aka bayar kuma eriyar da aka yi amfani da ita don wannan watsawar dole ne a sanya ta don samar da tazarar rabuwa aƙalla cm 20 daga kowane mutum kuma ba za a haɗa shi ko yin aiki tare da kowane eriya ko watsawa. Masu amfani da ƙarewa da masu girkawa dole ne a samar musu da umarnin shigarwa eriya da yanayin aikin watsawa don gamsar da ɗaukar fallasa RF.

Kanada, Masana'antu Kanada (IC) Sanarwa
Wannan na'urar ta dace da ƙa'idodin (s) RSS masu keɓanta lasisin Kanada.
Yin aiki ya dogara da sharuɗɗa biyu masu zuwa: (1) wannan na'urar bazai haifar da tsangwama ba, kuma (2) dole ne wannan na'urar ta yarda da duk wani tsangwama, gami da tsangwama da zai iya haifar da aikin na'urar.

Consult the dealer or contact [email kariya] neman taimako 

English V1.1

Takardu / Albarkatu

Zykronix Symphony XL 11.6 Inch Touch Panel [pdf] Jagoran Shigarwa
LBEE5ZZ1PJ, 2AGRR-LBEE5ZZ1PJ, 2AGRRLBEE5ZZ1PJ, Symphony XL 11.6 Inch Touch Panel, Symphony XL, 11.6 Inch Touch Panel

Bar Tsokaci

Your email address ba za a buga.