GTL1 Fitness Tracker

Activate

Activate Your Watch

Please charge the watch to activate it before first use.

Touch and Control

• Tap: Toggle function or wake up the screen.
• Tap and hold: Enter apps or submenus.
• Tap and hold for 3 seconds: Power on the device.

Charge Your Watch

Connect the magnetic charger to a USB power adapter. Align the charger correctly with the watch's charging contacts. Disconnect the watch after fully charging.

Notes: It is recommended to use a power adapter with an output voltage of 5V to avoid damage to the watch.

App Download and Connection

1. Download the Runmefit App

Get "Runmefit" from the App Store or Google Play. Alternatively, scan the QR code provided in the original documentation.

[QR code for app download]

2. Connect the Watch with Your Phone

Please make sure to always connect your watch through the Runmefit App. Do NOT directly connect it through the phone's system Bluetooth.

To connect:

1. Open the Runmefit app and navigate to "Device" > "Add device". Select your watch by its name.
2. Alternatively, on your watch, go to "Settings" > "Connect to phone" and scan the QR Code displayed on the watch through the Runmefit app.

[Visual description: A phone screen shows the Runmefit app interface with options like "Devices" and "Add device". Another visual shows a watch with its charging contacts and a phone displaying the app connection status.]

How to Wear the Device?

Wear the watch with the sensor side touching your skin. Leave approximately one finger's width between the edge of the watch and your wrist for optimal sensor contact and comfort.

[Visual description: A diagram illustrates the correct way to wear the fitness tracker on the wrist, showing the watch face and strap placement, and indicating the sensor contact with the skin.]

Precautions

• This product has an IP68 waterproof rating, suitable for daily water resistance like light rain, splashing water, and hand washing.
• Do not wear it for swimming, diving, hot showers, saunas, or other water sports.
• Avoid high-temperature environments to prevent damage.
• This product is not a medical device. All data and measurements are for reference purposes only and should not be used for medical diagnosis.

FAQ

1. Why can't I find or connect my device through the App?

Ensure your device is not already paired with your phone's Bluetooth system. If it is, go to your phone's "Settings" > "Bluetooth", select "Forget this device", and then re-pair it via the Runmefit App. For iOS users, you must accept the Bluetooth pairing request when the prompt appears for successful pairing.

2. Why can't my watch charge?

Verify that the positive and negative poles of the charger are correctly aligned with the watch's charging area. Check if the charger is properly connected to a power source and turned on. If the watch's battery is extremely low, allow some time for initial pre-charging before normal charging begins.

Support

For more questions, visit help.runmefit.com/hc/en-us.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions, complying with exposure requirements.