HUNTER Klein 19440 Light Pendant
- To avoid possible electrical shock, beforeinstalling your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location
- Dole ne kayan wuta su kasance a ƙasa. Idan wayar ƙasa don wurin shigarwa bata nan, nan da nan TSAYA shigarwa kuma tuntuɓi ƙwararren masanin lantarki.
- Duk wayoyi dole ne suyi daidai da lambobin lantarki na ƙasa da na gida ANSI / NFPA 70. Idan baku saba da wayoyi ba ko kuma kuna cikin shakka, tuntuɓi ƙwararren masanin lantarki.
KARANTA KUMA KA AJIYE waɗannan umarni
An bayar da waɗannan umarnin don amincinka. Yana da matukar mahimmanci a karanta su a hankali kuma gabaɗaya kafin fara shigar da kayan wuta.
Anan akwai kayan aikin da zaku buƙaci don kammala shigarwa
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture. Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. One end of the threaded post (H) should be attached to the mounting bracket (A) with a hex nut (G) in place. The other end should be connected to the canopy loop (E). Unscrew the canopy loop ring (F) from the canopy loop (E). Depending on the placement of your junction box the position of threaded post (H) may need to be adjusted to allow the canopy to be flush with the ceiling. Determine this by lifting mounting bracket (A) up to the junction box and place canopy (D) over the canopy loop (E), so that it is flush with the ceiling. Adjust the position of threaded post (H) on the mounting bracket (A) so that the canopy (D) covers at least half of the exterior threads on the canopy loop (E) while it is securely connected to threaded post (H). The threaded post (H) can be adjusted by loosening hex nut (G) to allow movement of threaded post (H) on mounting bracket (A). Once the ideal position of the threaded post (H) is determined, tighten up the hex nut (G) onto the threaded post (H) just beneath the mounting bracket (A) to secure the threaded post in place..
There are 4 12-inch rods (I), and 1 6-inch rod (J) included for each fixture. Determine the correct number of rods needed for proper hanging height. To lengthen the fixture, add additional rods. To shorten the fixture, trim the wires to desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the fixture’s wiring to discard. Keep in mind that you must use at least one rod to hang the fixture. Thread the wires through the rods and pull the wires until taut before connecting the rods together. Screw rod onto threaded post (K) on the fixture. Pull the fixture wires through the canopy loop ring (F), top of canopy (D), and canopy loop (E). Screw the top rod to canopy loop (E). Have a helper support the fixture’s weight and attach the mounting bracket (A) to the junction box by securely tightening the mounting screws (B).
Attach the fixture’s wires to the power supply wires from the junction box. Connect black to black (Live); white to white (grounded); grounding to grounding (green or copper). Twist the ends of the wire pairs together. Then, twist on a wire connector. Make sure all twists are in the same direction. Loop fixture’s ground wire around grounding screw (C) and tighten. If there is no ground wire (green or copper) from the junction box, contact a qualified electrician
Place the canopy (D) flush to the ceiling and slide the canopy loop ring (F) up beneath the canopy. Tightly screw canopy loop ring (F) onto the canopy loop (E) to properly secure the canopy (D) in place. Carefully install glass shade (M) over socket (L), then install socket cover (N) and tighten up the glass shade with socket ring (O). Install light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. An gama shigarwar ku yanzu. Kunna wutar lantarki kuma gwada kayan aiki.
Bi da tsayarwa a hankali! Tsaftacewa na yau da kullun zai rage buƙatar tsabtatawa mai zurfi. Don tsaftacewa ta yau da kullun, kashe wutar kuma goge abin gogewar tare da auduga mai tsabta mara launi ko kyallen microfiber. Kada a taɓa fesa mai tsabtace kai tsaye akan kayan aiki.
In order to use a 12in rod by itself you must first remove the post from the 6in rod and install it on one of the ends of the 12in rod
Mafarauta Pro Tip
Twist or tape wire ends together to make it easier to pass them through the downrods. Threaded post may also be removed for easier wire access
Takardu / Albarkatu
|HUNTER Klein 19440 Light Pendant [pdf] Jagoran Jagora|
Klein 19440, Klein, 19440, Light Pendant