CUSTOM CIRCUIT MK2 LED Light Bar

Bayanin samfur

• Ƙayyadaddun bayanai:
  • Samfura: Prusa MK2 / 2.5/3/4/S LED haske mashaya REV: V1
  • Mai ƙira: Kevin Petersson
  • Kwanan wata: Mayu 2024

Umarnin Amfani da samfur

• Gabatarwa
  • Na gode don siyan sandar hasken LED. Wannan jagorar zai bi ku ta hanyar shigarwa.
• Disclaimer
  • Bayanin da aka bayar yana nan kuma ba tare da garanti ba. Mai amfani yana ɗaukar duk alhakin shigarwa da amfani da wannan kayan haɓakawa.
• Abubuwan da ake bukata
  • Kayan aikin da ake buƙata: Phillips screwdriver. Tabbatar cewa kuna da abin da ake buƙata don hasken.
• Shigarwa
  • Mataki na 1 Hana hasken LED akan hannun hagu ta amfani da sukurori masu ɗaukar kai. Zabi, yi amfani da tayen zip don ƙarin taimako.
  • Mataki na 2 Shigar da goro na kulle a cikin Dutsen Z tare da daidaitawa mai kyau. Aiwatar da matsa lamba don kiyaye shi a wurin.
  • Mataki na 3 Shigar da hannun hagu a kan firinta, tabbatar da daidaitaccen matsayi na kebul kamar yadda aka nuna a cikin zane-zane.
  • Mataki na 4 Haɗa hasken zuwa allon haɓakawa ta bin umarnin da aka bayar kuma tsara cabling da kyau.

FAQs

• Tambaya: Zan iya amfani da nau'in screwdriver daban don shigarwa?
  • A: Ana ba da shawarar yin amfani da screwdriver na Phillips kamar yadda aka ƙayyade a cikin littafin don shigarwa mai kyau.
• Tambaya: Me zai faru idan na ci karo da raguwa mai yawa a cikin kebul yayin shigarwa?
  • A: Bi jagorar da aka bayar don cire duk wani abin da ya wuce kima a hannu don saitin tsafta.

Gabatarwa

Na gode don siyan wannan mashaya hasken LED. A cikin wannan ɗan gajeren jagorar, zan bi ta cikin manyan matakai na yadda ake shigar da hasken, don haka mu fara!

Disclaimer

• Ana ba da bayanin mai zuwa ”kamar yadda yake” kuma ba tare da garanti ta kowace iri ba, bayyananne ko fayyace.
• Ba zan ɗauki alhakin duk wani lahani na kowane irin da ya taso daga shigarwa ko amfani da wannan samfur na haɓakawa don firinta na Prusa ba, gami da, amma ba'a iyakance ga, kai tsaye, kaikaice, na bazata, ladabtarwa, da kuma lahani.
• Mai amfani yana ɗaukar duk alhakin shigarwa da amfani da wannan samfur na haɓakawa.

Abubuwan da ake bukata

Shigar da hasken kawai yana buƙatar amfani da na'urar sikelin Phillips; babu sauran kayan aikin da ake bukata.

Tabbatar cewa kun buga abin da ya dace don hasken, wanda za'a iya sauke shi anan. Har ila yau, tabbatar cewa kun sami waɗannan abubuwa masu zuwa:

• Hasken LED tare da kebul
• 10x dunƙule na kai

Shigarwa

• Mataki na 1
  • Don fara shigarwa, ɗauki Dutsen hannun hagu da hasken LED kuma yi amfani da ɗaya daga cikin screws masu ɗaukar kai don ɗaga shi a hannu, kamar yadda aka nuna a hoto 1.
  • Kuna iya amfani da tie ɗin zip na zaɓi don ƙarin damuwa, duk da haka, ba a buƙata ta biyu ba, dole ne ya zama siriri don dacewa da zarar an shigar da murfi.
• Mataki na 2
  • Mataki na gaba shine shigar da sashin ''locking nut'' a cikin Dutsen Z. Tabbatar cewa ɓangaren hexagonal yana fuskantar sama kuma cewa gefuna murabba'in suna fuskantar waje daga firinta.
  • Lura cewa an yi wa wannan ɓangaren madubi don ɗaukar kowane gefen firinta, kamar yadda aka kwatanta a hoto 2a na gefen hagu.
  • A hankali latsa goro na kulle sama cikin mariƙin har sai an ɗora shi lafiya, kamar yadda aka kwatanta a hoto na 2b.
  • Yana iya buƙatar ɗan matsa lamba don dacewa da kyau, amma ya kamata ya zauna lafiya da zarar an shigar dashi yadda yakamata. Maimaita wannan hanya don kishiyar gefen.
    • Hoto na 2: Makulli hoton shigarwa na goro inda (a) ya nuna daidaitaccen daidaitawa kuma (b) an ɗora shi a cikin mariƙin axis na Z.
• Mataki na 3
  • Na gaba, za mu ci gaba da shigar da hannun hagu a kan firinta. Kafin yin haka, tabbatar da cewa an saita cabling daidai a cikin ramin da aka keɓance, kamar yadda aka nuna a hoto na 3. Kula da ɗan jinkiri a cikin kebul don daidaitawa na gaba.
  • Yayin da ake riƙe kebul ɗin a hankali a maki 1 da 2, kamar yadda aka nuna a hoto na 3, liƙa hannun a kan mariƙin axis na hagu.
  • Tabbatar cewa hannu ya zauna jariri da mariƙin, kamar yadda aka nuna a hoto na 4, kula da kar a tsunkule kebul ɗin.
  • Bayan hawa, tabbatar da cewa kebul ɗin yana motsawa cikin yardar kaina ta hanyar ja gefe ɗaya a hankali. Idan kebul ɗin ba ta motsawa da kyau, ɗaga hannu kuma sake sanya kebul ɗin.
  • Da zarar kebul ɗin ya motsa cikin yardar kaina, yi amfani da dunƙule mai ɗaukar kai don amintar da hannu zuwa mariƙin, kamar yadda aka kwatanta a hoto na 5.
  • Ci gaba don ɗaga hannun dama. Wannan matakin ya fi sauƙi saboda babu haɗin igiyoyi. Tuna don amfani da dunƙule tawul ɗin kai don tabbatar da kishiyar ƙarshen LED akan hannun dama.
    • Hoto na 3: Kebul na tuƙi a cikin mariƙin tare da maki 1 da 2 yana nuna maki da aka ba da shawarar don riƙe kebul yayin hawa hannu.
• Mataki na 4
  • Yanzu lokaci yayi da za a haɗa hasken zuwa allon haɓakawa. Saka mai haɗa hasken cikin tashar LED, kamar yadda aka nuna a hoto 6a.
  • Don tsara cabling, a hankali tura shi cikin tashar kebul ɗin da aka keɓe akan mariƙin allo, kamar yadda aka nuna a hoto na 6b.
  • Bayan wannan mataki, za ku iya lura da raguwar raguwa a cikin kebul, kama da Hoto 7a. Don magance wannan, kawai a ja abin da ya wuce kima cikin hannu, bin jagorar da aka nuna a hoto na 7b.
  • Lura cewa da zarar an shigar da murfi, ba za a iya ganin wannan ɓacin rai ba.
    • Hoto na 6: (a) Yana nuna inda za'a toshe mai haɗawa zuwa hasken LED da (b) yadda yakamata ya kula da gyaran hanyar da tashar kebul a cikin mariƙin.
    • Hoto na 7: (a) Slack bayan amfani da tashar kebul akan mariƙin haɓakawa da (b) bayan ja lallausan zuwa hannu.
• Mataki na 5
  • Mataki na ƙarshe shine kawai shigar da murfi waɗanda aka ɗora tare da skru 3 na kai kowane murfi.

An gama

Yanzu kun gama shigarwa, don haka zaku ji daɗin firinta mai haske. Don ƙarin bayani game da hasken duba sashin da ke ƙasa.

Aiki

• Don kunnawa da kashe hasken, zaku iya amfani da maɓallan da ke kan hasken, lokacin da aka shigar da shi hasken yana ɗan ɗan fita kaɗan kamar yadda aka nuna a hoto na 9.
• Tura shi da sauƙi zuwa hagu zai kunna hasken kuma tura shi zuwa dama zai kashe hasken, amma ku tuna kuyi hankali da maɓalli don yana da ƙananan.
• Don daidaita haske kuna buƙatar ƙaramin lebur ko Phillips head screwdriver, don daidaita ƙaramin potentiometer wanda yake kamar yadda aka kwatanta a hoto na 10. Akwai ƙaramin rami a cikin murfi don haka yana yiwuwa a daidaita haske yayin hawa.
  • NOTE: Yi hankali don kada ku gajarta wani abu yayin daidaitawa kuma idan zai yiwu yi amfani da sukudireba filastik don kasancewa a gefen amintaccen!
  • Hoto na 9: Wurin sauya wutar lantarki don hasken da jagorar kunnawa da kashe hasken.
  • Hoto na 10: Wurin sauya wutar lantarki don hasken da jagorar kunnawa da kashe hasken.

Prusa MK2 / 2.5/3/4/S LED haske mashaya

• REV: V1
• Kevin Petersson
• Mayu 2024

Takardu / Albarkatu

CUSTOM CIRCUIT MK2 LED Light Bar [pdf] Jagoran Shigarwa MK2 LED Light Bar, MK2, LED Light Bar, Haske Bar, Hasken Bar

Magana

• Manual mai amfani