SIEPUNK 51.1 x 54 Inch Frameless Tri-Fold Pivot Bathtub Shower Door Instruction Manual

Gabatarwa

Thank you for choosing the SIEPUNK Frameless Tri-Fold Pivot Bathtub Shower Door. This manual provides essential information for the safe and correct installation, operation, and maintenance of your new shower door. Please read these instructions thoroughly before beginning installation and keep this manual for future reference.

Bayanin Tsaro

Tsaron ku shine mafi muhimmanci. Da fatan za a kiyaye waɗannan matakan kariya:

Always wear appropriate personal protective equipment, including safety glasses and gloves, during installation.
Handle glass panels with extreme care. Tempered glass is strong but can shatter if struck at the edges or corners.
Ensure the installation surface (wall, bathtub rim) is structurally sound and capable of supporting the weight of the shower door.
Use only the provided hardware or equivalent high-quality, load-bearing fasteners suitable for your wall type.
Do not attempt to install this product alone. Two or more people are required due to the size and weight of the glass panels.
Ka kiyaye yara da dabbobi daga wurin shigarwa.

Figure 1: Safety Tempered Glass. The shower door panels are constructed from 1/4 inch (6mm) thick ANSI-certified tempered glass, designed for safety and durability. This glass is resistant to impact and breakage, and if it does break, it shatters into small, less harmful pieces.

Abubuwan Kunshin

Please verify that all components are present and undamaged before beginning installation. If any parts are missing or damaged, contact customer support immediately.

Glass Panels (3 sections)
Wall Profile/Frame
Hinges (Top and Bottom)
Roba Gasket
Screws and Screw Washers
Screw Cap Covers
Silicone Sealing Strips
Spanner/Wrench

Saita da Shigarwa

Careful installation is crucial for the proper function and longevity of your shower door. Follow these steps precisely.

1. Determine Installation Side (Reversible)

The shower door is designed for reversible installation, allowing it to be mounted on either the left or right side of your bathtub opening, depending on your bathroom layout and preference.

Diagram showing left and right side reversible installation options for the shower door. — **Figure 2: Reversible Installation.** This diagram illustrates how the shower door can be configured for either a left-hand or right-hand opening, providing flexibility for various bathroom designs. The overall dimensions are approximately 51.2 inches wide by 54.3 inches high.

2. Wall Profile Shigarwa

Sanya bango profile against the wall at the desired height, ensuring it is plumb and level.
Mark the drilling points through the pre-drilled holes in the wall profile.
Drill holes into the wall using an appropriate drill bit for your wall material. Insert wall anchors if necessary.
Tsare bango profile to the wall using the provided screws. Ensure a tight and stable fit.

3. Hinge and Glass Panel Assembly

The hinges connect the glass panels and allow for the folding mechanism. Refer to Figure 3 for a visual guide.

Diagram showing steps for easy installation of glass clamps and hinges. — **Figure 3: Easy Installation Steps.** This diagram illustrates the process of attaching the glass clamps and hinges. **Mataki 1:** Unscrew the hinge. **Mataki 2:** Fix the rubber gasket onto the glass. **Mataki 3:** Install the screw washer. **Mataki 4:** Install the other side glass clamp. **Mataki 5:** Tighten screws with the spanner. **Mataki 6:** Put on the screw cap cover.

Mataki 1: Unscrew the hinge components to separate the clampfaranti.
Mataki 2: Place the rubber gaskets onto the glass panels where the hinges will be attached. These gaskets protect the glass and provide a secure grip.
Mataki 3: Position the hinge plates on either side of the glass panel, ensuring the rubber gaskets are correctly seated. Insert the screw washers.
Mataki 4: Align the screw holes and insert the screws.
Mataki 5: Using the provided spanner, carefully tighten the screws. Do not overtighten, as this can damage the glass. Ensure the glass is held firmly but without excessive pressure.
Mataki 6: Once all screws are tightened, place the screw cap covers over the exposed screw heads for a finished appearance and to prevent corrosion.
Repeat this process for all glass panels and hinges, connecting them sequentially.

4. Rufewa

Proper sealing prevents water leakage.

Close-up of a high-quality silicone strip preventing water leakage at the bottom of the shower door. — **Figure 4: Waterproof Design.** This image highlights the high-quality silicone strip installed at the bottom of the shower door panels, which effectively prevents water from leaking through the crevices and keeps the bathroom floor dry.

Install the silicone sealing strips along the bottom edge of the glass panels and between the panels where they meet.
Trim the strips to the correct length using a utility knife. Ensure a snug fit to create a watertight seal.
Apply a bead of silicone sealant along the exterior joint where the wall profile meets the wall and the bathtub rim for additional waterproofing. Allow adequate drying time before use.

Umarnin Aiki

Your SIEPUNK shower door is designed for smooth and convenient operation.

Image showing the modern folding design of the shower door, both folded and extended. — **Figure 5: Modern Folding Design.** This image demonstrates the foldable design of the shower door, showing it both fully extended to enclose the shower area and neatly folded back against the wall for easy access and space-saving.

Budewa: Gently push the outermost glass panel inward or outward. The pivot hinges allow the panels to swing 180 degrees, providing ample space for entry and exit.
Nadawa: To maximize space, fold the panels inward towards the wall. The tri-fold design allows the panels to stack neatly.
Rufewa: Extend the panels fully to create a complete shower enclosure. Ensure all panels are aligned to prevent water splashing.

Kulawa

Tsaftacewa da kulawa akai-akai zai tabbatar da tsawon rai da kuma bayyanar ƙofar shawa.

Gilashin Tsabtace

Comparison of ordinary glass with water spots versus nano-coated glass with water beading off. — **Figure 6: Easy to Clean Nano Coating.** This image demonstrates the effectiveness of the nano-coating on the glass, showing how water beads and runs off, significantly reducing limescale buildup and making the glass easier to clean compared to ordinary glass.

The glass features an Ultralux nano-coating for easy cleaning and reduced limescale buildup.
After each use, wipe down the glass panels with a soft cloth or squeegee to remove water droplets.
For general cleaning, use a mild, non-abrasive glass cleaner and a soft cloth. Avoid harsh chemicals, abrasive pads, or scouring powders, as these can damage the coating and glass surface.
Rinse thoroughly with water after cleaning.

Hinge and Frame Care

Close-up of a high-quality black copper hinge for the shower door. — **Figure 7: High-Quality Copper Hinge.** This image showcases the robust black copper hinges used in the shower door construction. These hinges are designed for superior corrosion resistance, stability, and smooth 180-degree operation, featuring a high-strength stainless steel internal structure.

Wipe down the matte black aluminum frame and hinges with a soft, damp zane.
Avoid using abrasive cleaners or solvents on the frame and hinges, as they can damage the finish.
Periodically check all screws and fasteners for tightness. Tighten gently if necessary, but do not overtighten.

Rubutun Rubutu

Inspect silicone sealing strips regularly for wear or damage. Replace them if they become brittle, cracked, or lose their sealing effectiveness.

Shirya matsala

Idan kun ci karo da wata matsala da ƙofar shawa, duba waɗannan matsalolin da mafita na yau da kullun:

Matsala	Dalili mai yiwuwa	Magani
Water leakage from bottom or sides	Improperly installed or damaged sealing strips; insufficient silicone sealant.	Inspect and adjust or replace sealing strips. Reapply silicone sealant where necessary, ensuring a continuous bead.
Door panels do not align or close properly	Hinges are loose or misaligned; wall profile not plumb.	Check and tighten hinge screws. Verify the wall profile is plumb and adjust if possible.
Difficulty opening or closing panels	Hinges are stiff or dirty; obstruction.	Clean hinges and apply a silicone-based lubricant if needed. Check for any obstructions in the door's path.
Glass appears cloudy or stained	Limescale or soap scum buildup.	Clean with a mild glass cleaner. For stubborn stains, use a specialized limescale remover safe for glass, then rinse thoroughly. Regular wiping after use helps prevent this.

Ƙayyadaddun bayanai

Siffar	Daki-daki
Alamar	SIEPUNK
Samfura	51.1 x 54 Inch Frameless Tri-Fold Pivot Bathtub Shower Door
Launi	Matte Black
Kayan abu	Tempered Glass, Aluminum
Gilashin Kauri	0.25 inci (6mm)
Takaddun Shaidar Gilashi	ANSI Certified
Dimensions (Width x Height)	51.2 inches x 54.3 inches (approximate, as per diagram)
Salo	Na Zamani, Mara Tsarin Firam
Nau'in Ƙofa	Tri-Fold Pivot
Nau'in Hinge	High-Quality Copper Hinges (with stainless steel internal structure)
Gilashin Shafi	Ultralux Nano-coating
Ana Bukatar Taro	Ee
Nauyin Abu	60 fam

Garanti da Taimako

For warranty information, technical support, or to order replacement parts, please contact SIEPUNK customer service. Refer to your purchase documentation for specific contact details or visit the official SIEPUNK website.