Reelcraft Industries - Hose, Cord, and Cable Reels
Instruction Manual for REELCRAFT models including: T-1460-7, T-1460-2, T-1460-4, T-1460-4 Safe Reel Welding Cable, T-1460-4, Safe Reel Welding Cable, Reel Welding Cable, Welding Cable, Cable
File Info : application/pdf, 3 Pages, 433.65KB
DocumentDocumentOperating Instructions Safe-T-Reel Welding Cable Reels Model Numbers: T-1460-7 T-1460-2 T-1460-4 Dimensions B E D T-1460-X A 19" B 18" A C 6" D 6" C Four 1/2" diameter mounting holes E 6 1/2" F 16 1/4" IMPORTANT Read this manual carefully before installing, operating or servicing this equipment. SAFETY Injury and/or equipment damage may result if proper safety precautions are not observed. · Ensure that only a qualified electrician installs/services this equipment. · Ensure that power supply voltage does not exceed maximum voltage rating of reel. · Ensure that reel is properly installed before connecting to power supply. · Ensure that all electrical power is removed from reel before servicing. · Check for frayed/broken wires before each use. · Pull electrical cord from reel by grasping the electrical cord itself, not the work device. · If an electrical malfunction should occur, remove power from reel immediately. · Ensure that reel, electrical cable, and equipment being serviced are properly grounded. Use an ohmmeter to check ground continuity. · If reel ceases to unwind or rewind, remove power immediately. Do not pull or jerk on electrical cable! · Treat and respect the cable reel as any other piece of machinery, observing all common safety practices. WARNING: Even low voltage can cause irreparable damage or death! Exercise extreme caution while operating or servicing this equipment. Form# 1105-801-OBSOLETE Rev: 02/2023 Reelcraft Industries, Inc. · 2842 E Business Hwy 30, Columbia City, IN 46725 Ph: 800-444-3134 / 260-248-8188 · Fax: 800-444-4587 / 260-248-2605 Customer Service: 855-634-9109 · reelcraft@reelcraft.com · www.reelcraft.com Safe-T-Reel Welding Cable Reels INSTALLATION INSTRUCTIONS Inspection Unpack and inspect reel for damage. Turn the reel by hand to check for smooth operation. Check for completeness. Mounting Note: Ensure that only a qualified electrician installs/services this equipment. 1. Four 1/2" diameter mounting holes are located at the base of the reel. Mount reel using four (customer supplied) bolts; tightening them securely to ensure a solid, rigid attachment. (Figure 1) Electrical Note: Observe any applicable NEC, OSHA, and local electrial codes when installing this equipment. 1. Attach a cable lug (customer supplied) to the end of the outlet cable. 2. Mount lug to collector ring assembly using one 1/2-13 UNC bolt. (Figure 2) Figure 1 Figure 2 Page 2 www.reelcraft.com Safe-T-Reel Welding Cable Reels 6 5 4 3 2 1 13 12 11 7 8 19 10 9 18 18 18 17 16 15 14 Item # Description 1 Self Tapping Screw 2 Spool Cover 3 Hex Cap Screw 4 Spool Half 5 Hose Clamp 6 Spool Half 7 Spool Cover 8 Shaft Key 9 Hex Jam Nut 10 Set Screw 11 Handle Post 12 Handle 13 Hex Jam Nut 14 Collector Ring Assembly 15 Tensioning Nut 16 Hub Assembly 17 Main Shaft 18 Base Assembly 19 Cord Grip Assembly 20 Lock Washer # Req 12 1 5 1 1 1 1 1 1 --1 1 2 1 1 1 1 1 1 1 T-1460-2 S285-14 261517 S2-85 261546 261541-1 261547 261518 261516 261575 None 261515 261514 S77-108 S600791 261548 S600752 261545 600746 261555 S115-816 T-1460-4 S285-14 261517 S2-85 261546 261541-1 261547 261518 261516 261575 None 261515 261514 S77-108 S600791 261548 S600752 261545 600746 261555 S115-816 T-1460-7 S285-14 261517 S2-85 261546 261541-1 261547 261518 261516 261575 None 261515 261514 S77-108 S600791 261548 S600752 261545 600746 261555 S115-816 www.reelcraft.com Page 3