User Manual for AMHVMU models including: P2 HUD Car Head up Display, P2, HUD Car Head up Display, Head up Display, Display
AMHVMU P2 HUD Car Head up Display, GPS Smart Speedometer with Over Speed Alarm Voltmeter Warning,3.5”HUD OBD2 plus GPS Dual System, Applicable to All Cars : Automotive
File Info : application/pdf, 7 Pages, 259.98KB
DocumentDocumentP2 OBD LCD Head up display (P2 has registered appearance patents in many countries and display screen copyrights) Description of the Interface and Button 1. Main button: Short press in Long press in Short push left Long push left Short push right Long push right 2. Light Sensor: Automatically adjusts the brightness according to the environment 3. Alternate interface 4. OBD cable interface 5. Rotatable bracket Description of the Button 1. Short press in (1s to release: A.Switch display interface B.Short press to confirm 2. Long press in 2s to releaseEnter setting mode, again to save and exit 3. Long push left 2s to releaseLong push left and the icon will flash, indicating that this functional area is selected, can switch and select this functional area ( PS: It will be automatically saved if no operation after 10s.) 4. Short push left : A.Toggle the blinking ribbon position B.Move options/adjust values after entering setting mode 5.Short push right setting mode A.Toggle the display function where the icon flashes B. Move options/adjust values after entering 5. Long push right Quick switch on/off Switch GPS system A. Plug in the USB cable, the device will automatically enter the GPS system B. Plugging in the OBD cable, long press in Switch", then select "OFF" to enter setting modefind "OBD Quick shutdown Long push right to quick shutdown and boot Slope meter calibration: Place the device well, turn off the car and the screen will shut down, then start the device again, and the calibration is complete Switch function icon Long push button then short push left , main interface icon flashes, to switch icon short push right to switch functionshort press in automatically exit after 5 seconds of no operation) Voltage Water temperature Oil temperature Instant fuel consumption Average fuel consumption Engine load Power battery power hydraulics pressure Fuel pressure to confirm( Will Driving distance Driving time Rotating speed Transmission oil temperature Turbo pressure Atmospheric pressure Exhaust gas temperature Oil quantity Tilt left and right Altitude Clock Tilt up and down Speed Driving direction OBD speed Function explanation Speed= Speed OIL T.= Oil temperature INS Fuel= Instant fuel consumption FUEL LEV.= Fuel quantity Altitude= Altitude GPS Speed= GPS Speed FUEL P.=Fuel pressure Week=Day of the week LAT=Latitude Direction=Driving direction HybridEle.=Power battery power VLT= Voltage CVT= Transmission oil temperature AVG Fuel= Average fuel consumption DriveDist= Driving distance GPS NumSv= Satellites number I.A.T.=Intake air temperature GPS Offst=GPS precision Time=Time Atmospher=Atmospheric pressure ENGINE Ld=Engine Load Coolant= Coolant temperature TURBO= Turbo pressure EGT= Exhaust gas temperature DriveTime= Driving time TACHO= Rotating speed OIL P.=Hydraulics pressure Date= Date G-Force=Accelerometer LON=Longitude Outside Temp=Outside temperature G-Roll A.=Left and right tilt angle G-Pitch A=Front and rear pitch angle Enter setting mode: Long press in to enter the setting modepush right to select setting itemshort press in to enter the setting itemafter adjustment long press in to saveagain to save and exit System Set Time Zone Speed Unit Brightness Dark TFT Contrast LED Brightness LED Dark LED Color OBD Switch Comd Search System setting Time adjustment Power On Power on method Speed unit Power Off Power off method Brightness adjustment LED Color Atmosphere light color The darkest brightness Turn Off Turn off voltage Contrast Atmosphere light brightness Brightness at night Quest Mode Communication mode Request Rate Communication speed Value Smooth Speed of digital change Color of atmosphere light Demo Display mode OBD switch Clear DTC Clear fault code Search PID instruction Factory Set Factory setting Special Fea Model Coolant T. Oil T. AT Oil T. Speed set Speed Choice Special feature Model Coolant temperature Oil temperature Automatic transmission oil temperature Fuel T. Outside T. I.A.T. Catalyst T. Speed setting Speed choice Speed Warning Fuel temperature Outside temperature Intake air temperature Catalyst temperature Speed warning ADJUST Speed Adjust RPM Adjust Turbo Adjust FUEL Set Fuel Unit Fuel Calcu ALARM Alarm Switch RPM Alarm Coolant Alarm Oil Temp Alarm EGT Alarm Data adjustment Speed adjustment RPM adjustment Turbo adjustment Fuel Adjust Voltage Adjust Fuel setting Fuel unit Fuel calculate Fuel Type Swept Volume Alarm setting Alarm switch RPM alarm Coolant temperature alarm Oil temperature alarm Exhaust temperature alarm OIL P. Alarm Fuel P. Alarm Voltage Alarm Rest Alarm Fuel adjustment Voltage adjustment Fuel type Engine swept Volume Oil pressure alarm Fuel pressure alarm Low voltage alarm Rest alarm FAQ 1.No display on the screen, no power Check whether the OBD cable is loosely connected, try to connect it several times. If it still does not work, please change another car to test, and analyze whether the OBD interface of the car is broken. If the OBD interface is broken, please repair the OBD interface and then connect the machine again. 2. Powered on, but P2 only displays voltage, and automatically turn off after 30 seconds OBD device are only suitable for OBDII and EOBD Please check the year of car production (OBDII and EOBD were used after 2008) HUD products do not support OBD I and JOBD, and the cars produced before 2008 Please connect directly with a USB cable. 3.The speed display on P2 is different from the instrument panel's Please check if the unit is correct: kilometer-KM/mile-MPH( Speed unit switching reference setting item). If the unit is correct: please long press in to enter the setting mode, choose "Adjust" and select "SPEED Adjust" (For example: the instrument displays 100 Km/h and the device displays 102 Km/h, adjust the parameter value to -2%). 3. Can't power on with car Enter setting mode, find "Power On"( The default is to automatically power on when the voltage exceeds 0.8V ), please adjust the value to 0.5V or 0.4V. PS: Setting the voltage too low will cause the machine to keep restarting. 4. Unable to shut down or automatically start and stop with the car (Gas-electric hybrid vehicle) Enter setting mode, find "Power Off" MODE 0: Judging that the communication conditions are in line with the preset, will power off in 5 seconds (suitable for most models) MODE 1: Judging that the speed and voltage conditions of the vehicle are in line with the preset, will power off in 5 seconds (suitable for special models) MODE 2: Special for automatic start and stop, or gasoline-electric hybrid vehicles 6.The time is not correct Enter setting mode, find "Time Zone"to adjust the time.