GATORBACK logo2022-C Navigator Mud Flap Set Anodized Rear
Instruction Manual

2022-C Navigator Mud Flap Set Anodized Rear

IMPORTANT:
Manufacturer is not responsible for negligent use of vehicle with mud flaps installed, including over-tightening of screws and bolts causing damage to vehicle or mud flaps.
TOOLS REQUIRED-GATORBACK 2022-C Navigator Mud Flap Set Anodized Rear - TOOLS REQUIREDFLAPS
GATORBACK 2022-C Navigator Mud Flap Set Anodized Rear - FLAPS

PARTS BAG # 770593
a) (10) Caps crew, 1/4”-20 x 1”, SS Balk Ox. Part #014073 GATORBACK 2022-C Navigator Mud Flap Set Anodized Rear - iconb) (12) Washer, Flat 0.281” x 1”, 18ga, SS Blk Ox. Part #018069
GATORBACK 2022-C Navigator Mud Flap Set Anodized Rear - icon 1c) (2) Washer, Lock 1/4” SS, Part #024000GATORBACK 2022-C Navigator Mud Flap Set Anodized Rear - icon 5d) (2) Nut, Hex 1/4-20, SS Part #025000GATORBACK 2022-C Navigator Mud Flap Set Anodized Rear - icon 2e) (8) Spring Nut 1/4-20 x 0.54” Reach Part #028010GATORBACK 2022-C Navigator Mud Flap Set Anodized Rear - icon 3f) (10) Washer, Nylon 0.281”x0.885”x0.062” Part #054080GATORBACK 2022-C Navigator Mud Flap Set Anodized Rear - icon 1g) (2) Durashield 5/8” X13” Protection Tape Part #766424GATORBACK 2022-C Navigator Mud Flap Set Anodized Rear - icon 4

INSTALLATION

(For ease of installation it is suggested that the wheel be removed)

  1. Before you install your Mud Flap Set, see the diagram and parts list for all necessary parts.
  2. Remove the four factory push pins located on the inner fender.
  3. Pull back the liner and install spring nuts (e) to the tabs that hold the liner in place.
  4. Hold the mud flap in place and use a marker to mark about 1/4” above the mud flap.
  5. Install dragstrip (g) from the mark down the edge of the vehicle. This protects the paint and body from the mud flap.
  6.  Loosely install mud flap holes #1 to #4 to spring nuts (e) using a capscrew (a), flat washer (b), and nylon washer (f).
  7.  Push the mud flap hole #5 against the factory liner and drill a 1/4” hole through the mud flap hole into the factory liner.
  8.  Loosely install mud flap hole #5 to liner using a capscrew (a), flat washer (b), and nylon washer (f) and secure using a flat washer (b), lock washer (c) and hex nut (d).
  9. Using a square or another levelling tool, ensure that the mud flap is level. Tighten all fasteners.
  10. Repeat procedure on passenger side.
    GATORBACK 2022-C Navigator Mud Flap Set Anodized Rear 1

Please check out our YouTube channel to see an install video for this application.

GATORBACK 2022-C Navigator Mud Flap Set Anodized Rear - icon 6

Documents / Resources

GATORBACK 2022-C Navigator Mud Flap Set Anodized Rear [pdf] Instruction Manual
2022-C Navigator Mud Flap Set Anodized Rear, 2022-C, Navigator Mud Flap Set Anodized Rear, Mud Flap Set Anodized Rear, Set Anodized Rear, Anodized Rear, Rear

References

Leave a comment

Your email address will not be published. Required fields are marked *