Garage-logoa

Garage Basics ARHS5B 5 Shelf Storage Rack

Garage-Basics-ARHS5B-5-Shelf-Storage-Rack-product

Specifications

  • Product: 5-Shelf Storage Rack

Tools

Garage-Basics-ARHS5B-5-Shelf-Storage-Rack- (1)

Safety

Garage-Basics-ARHS5B-5-Shelf-Storage-Rack- (2)

5-Shelf Storage Rack

Contents
Before getting started,ensure the package contains the following components:

Garage-Basics-ARHS5B-5-Shelf-Storage-Rack- (3)

Assembly

Step 1
Insert the protective coversGarage-Basics-ARHS5B-5-Shelf-Storage-Rack- (4)

  • Insert all 4 protective covers E to the bottom of the post C insert another 4 protective covers E to the top of the remaining 4 pieces post C.
  • Note: Do not omit this step, which could protect your floor from scratches.

Step 2
Setting Up the Brace Garage-Basics-ARHS5B-5-Shelf-Storage-Rack- (5)

  • Slide the rivets of brace B into posts C of your desired location with the key slot pointing down and shelf ledge of brace B facing up. Tap lightly to seat rivets.
  • Note: Make sure all the rivets are fully seated into the post slots. You may want to use a rubbem mallet (not included) to help push the rivets into the post slots. This applies to all the rivets uses in this unit.

Install as follows

Garage-Basics-ARHS5B-5-Shelf-Storage-Rack- (6)

Step 3
Setting Up the Beams and the Braces Garage-Basics-ARHS5B-5-Shelf-Storage-Rack- (7)

  • Repear the previous step 2 to attach beams A and braces B to posts C until the first and the second levelsare assembled.
  • Note: Each of the beams A and braces B on the same level should be at the same height.

Step 4
Setting Up the Upper Post

Garage-Basics-ARHS5B-5-Shelf-Storage-Rack- (8)

Put the connector G into the top of the bottom post to install the upper post

Step 5
Setting Up the remaining Beams and Braces

  • Garage-Basics-ARHS5B-5-Shelf-Storage-Rack- (9)Repeat step 2 and step 3 to assemble the remaining beams and braces

Step 6:
Setting Up the press boards Garage-Basics-ARHS5B-5-Shelf-Storage-Rack- (10)

  • Hold the press board at an angle to make it easier to fit them onto each previously assembled level on the frame.

Step 7:
Fixed to the wall

Garage-Basics-ARHS5B-5-Shelf-Storage-Rack- (11)

  • Use the anti-dumping device F to snap into the hole of the post , punch a hole on the wall, put the expansion screw in, and use the screw to pass through the connector to connect with the expansion screw

SAFETY AND COMPLIANCE

Please read and understand this entire manual before using the product.

CAUTION

  • Be aware of dynamic loading! Sudden load movement may briefly create excess load causing product failure.
  • Evenly distribute the weight on each shelf, and keep the heaviest loads on the bottom shelf.
  • Use only on flat, level and hard surface capable of supporting the shelving and any items placed on it. Remember to only use the shelf on level ground with evenly distributed weight.
  • Do not store flammable liquids in the unit unless they are secured in an approved container. Keep bystanders out of the area during assembly.
  • This product is not a toy. Do not allow children to play with, on or near the unit.

WARNING

Garage-Basics-ARHS5B-5-Shelf-Storage-Rack- (12)Do not stand on, step on, or alter this unit for anything outside the designed function of storage.
Garage-Basics-ARHS5B-5-Shelf-Storage-Rack- (13)Use care when handling and assembling metal parts.
Garage-Basics-ARHS5B-5-Shelf-Storage-Rack- (14)The metal may have sharp edges or corners . The use of protective gloves is recommended.
Garage-Basics-ARHS5B-5-Shelf-Storage-Rack- (15)Always remember to use proper lifting techniques when moving the boxed or assembled unit.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list. lf any part is missing or damaged, do not attempt to assemble the product .It is recommended that this product be assembled on a clean, soft surface, such as a piece of cardboard. The assembling task can be performed by one person but availability of a second person will make the task simpler.

TROUBLESHOOTING

PROBLEMPOSSIBLE CAUSEPROBLEM
 Shelf is not level
  •  Beam(s) or brace(s) used for the same level are not at the same height or theyare assembled upside down.
  •  Rivets on the beam(s) or brace(s) arenot fully seated into the post slots.
  • The ground is uneven or too soft.
  •  Re-assemble beam(s) or brace(s).
  •  Fully seat the rivets.
  •  Move the shelf to a flat, level and hard surface.

Hello there!
We’re excited to offer you seamless service.

You can contact us through the following methods on the right to access the following :

302-498-1264
olffurniture@gmail.com
simplyscan our Whatsapp QR code

  1. Comprehensive installation videos
  2. Activate warranty options
  3. Expert post-sales support
  4. Exclusive discounts
  5. And more additional servicesGarage-Basics-ARHS5B-5-Shelf-Storage-Rack- (16)

Our goal is to enhance your shopping experience. We look forward to hearing from you. Thank you!

After-sales service

Our storage rack after-sales service is designed to ensure your complete satisfaction and peace of mind.

If you encounter any issues, whether it is about assembly, usage tips or maintenance, please feel free to contact our dedicated customer support team at the after-sales phone number: 978-254 -2003 (It is best to send it via text message, and email is most recommended.) After-sales email: huluwat_ct@163.com.
Our products come with a hassle-free return and exchange service within 90 days to ensure that your storage rack continues to meet your needs.
With our after-sales service, you can trust that we will support you long after your purchase.

Documents / Resources

Garage Basics ARHS5B 5 Shelf Storage Rack [pdf] Installation Guide
ARHS5B 5 Shelf Storage Rack, ARHS5B 5, Shelf Storage Rack, Storage Rack, Rack

References

Leave a comment

Your email address will not be published. Required fields are marked *