GAMEMAX F45 ATX Gaming Case
Specifications:
- ATX Gaming Case
- Supports Motherboard Sizes: ATX, Micro-ATX, Mini-ITX
- Front Panel: USB 3.0, USB 3.0 Type-C Gen2, Combo Audio, Power SW
- Fan Cooling System:
- Front: 3x120mm (included), 2x140mm (included)
- Bottom: 3x120mm / 2x140mm (optional)
- Rear: 1x120mm (included)
- Liquid Cooling System:
- Front: 120/240/280/360mm (optional)
- Rear: 120mm (optional)
Product Usage Instructions
PSU Installation:
Insert the PSU from the right side and secure it with screws.
Motherboard Installation:
Install the motherboard, attach the I/O shield, and tighten the screws.
SSD and HDD Installation:
Install SSD and HDD without lock screws for easy setup.
GPU Card Installation:
Use the GPU card holder to secure your graphics card in place.
Fan and Liquid Cooling Setup:
Follow the provided guidelines to set up the fan and liquid cooling systems for optimal performance.
Airflow Direction:
Pay attention to the airflow direction inside the chassis for efficient cooling.
FAQ:
- Q: How many fans are included with the case?
A: The case comes with 3x120mm fans for the front panel and 1x120mm fan for the rear panel. - Q: Can I install a liquid cooling system in this case?
A: Yes, you can install a liquid cooling system on the front and rear panels as per the specified sizes.
Package Content
| Image | Q’ty | Used for | |
| A |  | 14 | MB Screw |
| B |  | 4 | PSU Screw |
| C |  | 8 | 3.5” HDD Screws |
| D |  | 8 | 2.5” SSD Screws |
| E |  | 14 | Hard Drive Damper |
| F |  | 1 | Hex Wrench
|
| G |  | 5 | Motherboard Standoff |
| H |  | 6 | Cable Tie |
Connectors
I/O Panel
Exploded View
Fron x3(included)- Rear 120mm fan xt Panel
- Left side panel
- Right side panel
- Chassis
- Detachable bottom plate
- GPU Card Holder
- IO Component
- Front 120mm fan1(included)
Installation Guide
Remove the left and right side panel and bottom plate
Remove the front panel
*If the fan has been pre-installed in front, no need to remove the panel 
Insert PSU from right side, secure with screws. 
Put in the motherboard, place the I/O baffle, and lock the screws. 
- Open the magnetic PCI-E baffle
- Remove the PCI-E interface card, put it in the graphics card, lock the screw fixation
Install SSD and HDD lock -free screws 
Install 3.5″ HDD and 2.5″ SSD 
Install 3.5″ HDD and 2.5″ SSD
* If a 3.5-inch hard drive is installed at the bottom, only 2*120mm fans or 1*140mm fan can be installed.
Cooling System
Fan Cooling System:
- Front: 3x120mm(included), 2x140mm(included) Bottom: 3x120mm / 2x140mm(optional)
- Rear: 1x120mm(included)
Airflow Direction
Pay attention to the airflow direction inside the chassis. 
V5.0 PWM ARGB HUB 
REMOTE CONTROL BUTTON FUNCTION
Power Up with GameMax, Gaming to the Max !
Documents / Resources
 | GAMEMAX F45 ATX Gaming Case [pdf] User Manual F45 ATX Gaming Case, F45, ATX Gaming Case, Gaming Case, Case |
 | GAMEMAX F45 ATX Gaming Case [pdf] User Manual 240808, F45 ATX Gaming Case, F45 ATX, Gaming Case, Case |
