FORTRESS LF122I Elbow Solúbtha

treoracha suiteáil

  1. Determine the path which the lineset will follow and strike a chalk line to mark the surface material. Attach the base only of all fittings first (ducting will be placed last), along the marked path, using fasteners of sufficient length (not provided). Predrill where necessary. Duct must terminate with a fitting to prevent cover from sliding out of position.
  2. Once all fitting bases are secured to the structure, measure and cut ducting to fit as needed. Remember to account for some seasonal expansion and contraction. Install and fasten ducting bases. Attach bases to structure using fasteners of sufficient length (not provided)
  3. Position and twist in lineset duct clips evenly spaced throughout installation. Nylon cable ties (not included) slip through lineset duct clips and fasten around lineset.
  4. Run lineset, drain hose, wiring etc. over the fitting and duct bases and secure to duct clips using tie wraps of sufficient size.
  5. Snap straight duct top over mating straight base pieces. Seat fitting tops over mating fitting bases and secure with provided stainless steel screws. Duct must terminate with a fitting to prevent cover from sliding out of position. If duct is to be painted, or duct is a dark color, adhere cover to base with pvc cement.

Toilleadh gnáthsraith líne* 92mm 31/2″ W x 21/2″D

92mm w/Single 1-1/8″ Lineset
BTU – 60,000
Suction Line – 1-1/8″ OD
(Insulation) – 1/2″
Liquid Line – 1/2″ OD
Drain Line – 3/4″ PVC

92mm w/Dual 3/4″ Lineset
BTU – 36,000
Suction Lines – 3/4″ OD
(Insulation) – 3/8″
Liquid Lines – 3/8″ OD
Drain Line – 3/4″PVC

92mm w/Single 3/4″ Lineset
BTU – 42,000
Suction Line – 3/4″ OD
(Insulation) – 1/2″
Liquid Line – 3/8″ OD
(Insulation) – 1/2″
Hose Drain - 7/8″ OD

122mm 41/2″ W x 31/4″ D

122mm w/Single 1 1-1/8″ Lineset
BTU – 60,000
Suction Line – 1-1/8″ OD
(Insulation) – 1″
Liquid Line – 1/2″ OD
Drain Line – 3/4″ PVC


122mm w/Dual 3/4” Lineset ▶

BTU – 42,000
Suction Lines – 3/4″ OD
(Insulation) – 1/2″
Liquid Lines – 3/8″ OD
(Insulation) – 1/2″
Drain Hose – 7/8” OD


◀ 122mm w/Dual 3/4″ Lineset 

BTU – 36,000
Suction Lines – 3/4″ OD
(Insulation) – 1/2″
Liquid Lines – 3/8″ OD
Drain Line – 3/4″ PVC

Treoracha suiteála speisialtachta

Adaptóir duct / LFJ solúbtha

INLINE COUPLING

  1. Secure fitting and duct bases to structure.
  2. Cut LF duct to length and place in LFJ adaptor.
  3. Secure LF duct with split cap and two stainless steel screws.
  4. Secure LF duct into adaptor by fitting second part of cap.

Ducht solúbtha / flange balla LWF

WALL CONNECTION

  1. Seal and attach LWF wall flange to structure.
  2. Place LF duct into LWF wall flange.
  3. Clamp Ducht LF le caipín agus dhá scriúnna cruach dhosmálta.
LEN Feisteas deiridh

LEN end fitting provides critical support to the lineset duct cover.
Without this fitting, the duct cover can slide out of place.
Chun an oscailt a choigeartú de réir mhéid an tsraith línte, níl le déanamh ach an deireadh a fheistiú ar feadh an groove atá ag teastáil, agus briseadh as na hailt nach dteastaíonn.
Is féidir an cúplóir LJ a úsáid freisin ag an deireadh duchta le haghaidh líonadh línte níos mó.

LG Gusset

LG Gussets are used for horizontal line duct installations, adding additional support to the duct.
(1) After installing the line duct base plate horizontally on a wall, identify where the gussets will be installed on the duct.
(Recommendation – install gussets every 16” center on stud or as needed on the install)
(2) Screw gussets into the top portion of the
Fortress Line duct as shown. Screws not provided.

Liosta Feistiú

Fitting List Available in WHITE, IVORY, BROWN and GRAY. Sizes 3 1/2” (92mm) or 4 1/2” (122mm).

Ducting (90″ lengths) LD
Couplerx LJ
Inlet Balla LW
Inlet bróige LP
Feistiú Deiridh LEN
90° Flat Ellen LK
45° Flat Ellen LKF
    LF122I Flexible Elbow Fitting List      90° Laistigh Ingearach El LCI
LF122I Flexible Elbow Fitting List 90° Outside Vertical Ell LCO
LF122I Flexible Elbow Fitting List 45° Laistigh Ingearach El LCFI
LF122I Flexible Elbow Fitting List 45° Outside Vertical Ell LCFO
LF122I Flexible Elbow Fitting List Tee LT
reducer LDR
90° Sweep Ell LKS
LF122I Flexible Elbow Fitting List Solúbtha Ell LF
LF122I Flexible Elbow Fitting List Adaptóir Solúbtha LFJ
LF122I Flexible Elbow Fitting List Flange Balla Solúbtha LWF
LF122I Flexible Elbow Fitting List 45˚-90˚ Adjustable Outside Vertical Ell ATF
LF122I Flexible Elbow Fitting List 45˚-90˚ Adjustable Flat Ell LKA
LF122I Flexible Elbow Fitting List Gearrthóga Twistlock Lineset* LDC
LF122I Flexible Elbow Fitting List Gussets* LG

*Gabhálais duchtaithe inmheánacha ar fáil i mbán amháin. Le húsáid ar mhéideanna duchta 3½ & 4½ araon.

RectorSeal® 2601 Spenwick Drive Houston, TX 77055 800-231-3345 reachtaire.com
RectorSeal, the logos and other trademarks are property of RectorSeal, LLC, its affiliates or its licensors and are protected by copyright, trademark and other intellectual property laws, and may not be used without permission. RectorSeal reserves the right to change specifications without prior notice. ©2022 RectorSeal. All rights reserved. R50870-0522

FORTRESS-Logo.png

Doiciméid / Acmhainní

FORTRESS LF122I Elbow Solúbtha [pdf] Lámhleabhar Treoracha
Elbow Solúbtha LF122I, LF122I, Elbow Solúbtha, Elbow

tagairtí

Fág tagairt

Nach mbeidh do sheoladh r-phoist a fhoilsiú. Réimsí riachtanacha atá marcáilte *