Honeywell logo

H-Klasse - logo

HD Peel & Present Option

Honeywell OPT78-2627 H-Klasse Oandreaun ynterne weromspoelopsje - detamexrjocht troch ús klanten.

Honeywell OPT78-2613-04 H-Klasse Thermal Transfer Opsje

overview

This document describes the contents, installation, and use of the Heavy Duty Peel and Present option for the H-Class printer. After verifying the contents of the kit and the tools needed, follow the steps below to install and begin using the option. A maintenance procedure is also included, so keep this documentation for future reference.

Warskôging FOARSICHTIGENS
For your safety and to avoid equipment damage, always turn ‘Off’ power and unplug the printer’s power cord before beginning this installation and when performing service.

Contents of the Heavy Duty Peel and Present Option

Dizze kit befettet it folgjende item:
• Heavy Duty Peel and Present Assembly

Honeywell H-4310 H-Class HD Peel and Present Option - Heavy Duty Peel and PresentArk fereaske
Om dizze opsje te ynstallearjen, sille jo in standert schroevendraaier hawwe.

Stap 1: De printer tariede

A) Skeakelje 'Ut' de Power Switch en losmeitsje de macht cord út de AC reservoir.

Honeywell H-4310 H-Class HD Peel and Present Option - Preparing the Printer

B) Druk op 'e Fange, dan lûke foarút te fuortsmite de Doar.

Honeywell H-4310 H-Class HD Peel and Present Option - DoorC) Ferheegje de Tagong Cover en ferwiderje jo media fan 'e printer.

Honeywell H-4310 H-Class HD Peel and Present Option - Access Cover

D) Fuortsmite Thumbscrew en Tear Plate. (Alternately, if equipped with an Arc Plate, Present Sensor, or Cutter, remove that device.)

Step 2: Installing the Heavy Duty Peel and Present Assembly

A) Druk op 'e Latch en iepenje de Peel and Present Gearkomste.

Honeywell H-4310 H-Class HD Peel and Present Option - Present Assembly

B) Druk foarsichtich op de Peel and Present Assembly yn de Front Plate Connector.

Honeywell H-4310 H-Class HD Peel and Present Option - Peel and Present

C) Draai de Befestigingsskroef te befeiligjen de Peel and Present Assembly nei de printer.

Stap 3: De opsje brûke
Tidens de operaasje sille etiketten wurde skuord út it backing materiaal en dispensed "on-demand" - dat is, folgjende printing sil plakfine pas neidat in earder printe label is fuortsmiten fan de printer. As herinnering sil "REMOVE LABEL" wurde werjûn om jo te freegjen as in label wachtet op ferwidering.

Begjin mei it brûken fan de opsje as folget:

A) Lade Media (sjoch de Operator's Manual foar details). Útwreidzje 20 inches (50 sm) fan Media fan de printer.

Honeywell H-4310 H-Class HD Peel and Present Option - Media

B) Fuortsmite de labels út dizze útwreide diel fan media, leaving allinne de Backing Materiaal. Crease de foaroansteande râne fan dit BackingMaterial.
C)
Rûte de Backing Materiaal ûnder de Assist Roller en de Internal Rewinder.

Honeywell H-4310 H-Class HD Peel and Present Option - Backing

D) Wikkel de Backing Materiaal yn in tsjin de klok yn rjochting om 'e Rewinder Hub and insert the creased leading edge into one of its Slots. Insert the Media Klem (Item 6) into the Slot over the creased leading edge of the Stipe Material and around the Rewinder Hub.

Honeywell H-4310 H-Class HD Peel and Present Option - Backing Material

E) Slute de Peel and Present Assembly. Close the Access Cover, plug the power cord into the AC Receptacle, and turn ‘On’ the Power Switch.

Honeywell H-4310 H-Class HD Peel and Present Option - Peel and Present Assembly

F) Soargje derfoar KLEAR is displayed on the Front Panel then press the FEED Key en gean troch neffens jo observaasjes:

  • If REMOVE LABEL is displayed on the Front Panel, this completes the installation; or,
  • If REMOVE LABEL is not displayed on the Front Panel, proceed to step 4: “Configuring the Printer.”

Honeywell H-4310 H-Class HD Peel and Present Option - Front Panel

Notes:

  1. De wurking fan 'e Present Sensor op dizze opsje kin ek wurde regele troch host-software-kommando's, dus soargje derfoar dat jo etiketteprogramma goed is ynsteld foar gebrûk by it ferstjoeren fan labelformaten nei de printer.
  2. As dizze opsje wurdt fuortsmiten mei macht tapast, de printer sil gedrage as oft in label wachtet fuortheljen; om normale wurking te herstellen, cycle macht nei de printer.

Stap 4: Konfigurearje de printer

While the Heavy Duty Peel and Present option is a plug-and-play device, this step may be necessary if the printer’s default configuration has been changed. Follow the steps below to configure the printer:

Noat: Yn 'e folgjende proseduere, rieplachtsje de Operator's Manual foar detaillearre ynstruksjes foar it frontpanel.

A) Druk op 'e MENU Button on the printer’s front panel.
B) De ... brûke OMLEECH Button, scroll to PRINTER OPSJES then press the Right Button.
C) De ... brûke OMLEECH Button, scroll to PRESENT SENSOR druk dan op de ENTER toets.
D) De ... brûke OMLEECH Button, scroll to MODE druk dan op de ENTER toets.
E) De ... brûke OMLEECH Button, scroll to AUTO druk dan op de YNGEAN Kaai.
F) Druk op 'e ÚTGONG Key then, at the Wizigingen opslaan? prompt, selektearje JA om de ynstallaasje te foltôgjen.
G) Turn the Power Switch 'Út' en ‘On’ to reset the printer and complete the configuration.

Noat: If the printer fails to separate the labels from the backing material, and the Internal Rewinder is not turning, it may need to be enabled. Using the procedure above as a guide, press the MENU Button, scroll to PRINTER OPTIONS, dan nei REWINDER, en selektearje AUTO. Afterward, press the ÚTGONG key and save your changes when prompted.

Maintaining the Heavy Duty Peel & Present Assembly

To ensure trouble-free operation, the Heavy Duty Peel and Present Assembly should be cleaned after every 100,000 inches (254,000 cm) of media use. This interval depends on the label adhesive, where “gummy” adhesives may require more frequent cleaning. (To easily track label usage, go to SYSTEM SETTINGS → MEDIA COUNTERS in the printer’s menu system.)

Clean the assembly as follows:

  1. Skeakelje de Power Switch 'Ut' en lûke it netsnoer út 'e AC Receptacle. Ferheegje de tagongsdeksel en ferwiderje de media fan 'e printer.
  2. Remove the Peel & Present Assembly from the printer.
  3. Mei help fan komprimearre lucht of in sêfte boarstel, skjin de sensoren on the assembly.Honeywell H-4310 H-Class HD Peel and Present Option - SensorsNoat: Foar it skjinmeitsjen fan swiere ôfsettings kin isopropylalkohol brûkt wurde - op betingst dat it foarsichtich wurdt tapast mei in katoenen swab, en dan tastien te droegjen foardat jo de opsje opnij ferbine mei de printer.
  4. Druk op 'e Latch to open the Peel and Present Assembly. Then remove the C-klip that secures the Upper Roller Shaft oan 'e Foarkant.Honeywell H-4310 H-Class HD Peel and Present Option - Front Cover
  5. Remove the Upper Roller Shaft and the associated Rollers.Honeywell H-4310 H-Class HD Peel and Present Option - Rollers
  6. Mei in a Katoenen swab dampened with alcohol, wipe all roller en Upper Roller Shaft surface clean. Pay special attention to the ridges on the Rollers to ensure that they are clean.
    Noat: For cleaning heavy deposits from the Rollers and Shafts in the following steps, WD-40 or another non-damaging adhesive remover can be substituted for isopropyl alcohol – provided this adhesive remover is carefully applied using a cotton swab.
  7. Slide de Rollers werom op 'e Upper Roller Shaft, place the components into the Front Cover, and reinstall the C-Clip.
  8. Triuwe en elevator beide Tabs dat feilich de Lower Roller Assembly to the Front Cover (as shown) and then, while keeping it intact, carefully remove the entire Lower Roller Assembly.Honeywell H-4310 H-Class HD Peel and Present Option - Tabs
  9. Take note of the individual roller positions – they must be reinstalled in the same order – then, carefully remove the Rollers fan de Lower Roller Shaft.Honeywell H-4310 H-Class HD Peel and Present Option - Lower Roller Shaf
  10. Mei in a Katoenen swab dampened with alcohol, wipe all roller en Lower Roller Shaft surfaces clean. Pay special attention to the ridges on the Rollers to ensure that they are clean.
  11. Slide de Rollers, in their original order, onto the Lower Roller Shaft and reinstall them in the Front Cover, soargje derfoar dat de Tabs are properly seated. Reinstall the Peel and Present Assembly onto the printer to complete the cleaning procedure.

Dokuminten / Resources

Honeywell H-4310 H-Class HD Peel and Present Option [pdf] Ynstruksjes
H-4310, H-Class, HD Peel and Present Option, H-4310 H-Class HD Peel and Present Option

Lit in reaksje efter

Jo e-mailadres wurdt net publisearre.